Age | Commit message (Collapse) | Author |
|
commit 60f59ce0278557f7896d5158ae6d12a4855a72cc upstream.
These drivers need to be able to reference "struct ieee80211_hw" from
the driver's private data, and vice versa. The USB driver failed to
store the address of ieee80211_hw in the private data. Although this
bug has been present for a long time, it was not exposed until
commit ba9f93f82aba ("rtlwifi: Fix enter/exit power_save").
Fixes: ba9f93f82aba ("rtlwifi: Fix enter/exit power_save")
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ba9f93f82abafe2552eac942ebb11c2df4f8dd7f upstream.
In commit a5ffbe0a1993 ("rtlwifi: Fix scheduling while atomic bug") and
commit a269913c52ad ("rtlwifi: Rework rtl_lps_leave() and rtl_lps_enter()
to use work queue"), an error was introduced in the power-save routines
due to the fact that leaving PS was delayed by the use of a work queue.
This problem is fixed by detecting if the enter or leave routines are
in interrupt mode. If so, the workqueue is used to place the request.
If in normal mode, the enter or leave routines are called directly.
Fixes: a269913c52ad ("rtlwifi: Rework rtl_lps_leave() and rtl_lps_enter() to use work queue")
Reported-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 2c7d0602c815277f7cb7c932b091288710d8aba7 upstream.
commit 848496e5902833600f7992f4faa82dc1546051ba
Author: Ville Syrjälä <ville.syrjala@linux.intel.com>
Date: Wed Jul 13 16:32:03 2016 +0300
drm/i915: Wait up to 3ms for the pcu to ack the cdclk change request on SKL
increased the timeout to match the spec, but we still see a timeout on
at least one SKL. A CDCLK change request following the failed one will
succeed nevertheless.
I could reproduce this problem easily by running kms_pipe_crc_basic in a
loop. In all failure cases _wait_for() was pre-empted for >3ms and so in
the worst case - when the pre-emption happened right after calculating
timeout__ in _wait_for() - we called skl_cdclk_wait_for_pcu_ready() only
once which failed and so _wait_for() timed out. As opposed to this the
spec says to keep retrying the request for at most a 3ms period.
To fix this send the first request explicitly to guarantee that there is
3ms between the first and last request. Though this matches the spec, I
noticed that in rare cases this can still time out if we sent only a few
requests (in the worst case 2) _and_ PCODE is busy for some reason even
after a previous request and a 3ms delay. To work around this retry the
polling with pre-emption disabled to maximize the number of requests.
Also increase the timeout to 10ms to account for interrupts that could
reduce the number of requests. With this change I couldn't trigger
the problem.
v2:
- Use 1ms poll period instead of 10us. (Chris)
v3:
- Poll with pre-emption disabled to increase the number of request
attempts. (Ville, Chris)
- Factor out a helper to poll, it's also needed by the next patch.
v4:
- Pass reply_mask, reply to skl_pcode_request(), instead of assuming the
reply is generic. (Ville)
v5:
- List the request specific timeout values as code comment. (Ville)
v6:
- Try the poll first with preemption enabled.
- Add code comment about first request being queued by PCODE. (Art)
- Add timeout_base_ms argument. (Ville)
v7:
- Clarify code comment about first queued request. (Chris)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Art Runyan <arthur.j.runyan@intel.com>
Cc: <stable@vger.kernel.org> # v4.2- : 3b2c171 : drm/i915: Wait up to 3ms
Cc: <stable@vger.kernel.org> # v4.2-
Fixes: 5d96d8afcfbb ("drm/i915/skl: Deinit/init the display at suspend/resume")
Reference: https://bugs.freedesktop.org/show_bug.cgi?id=97929
Testcase: igt/kms_pipe_crc_basic/suspend-read-crc-pipe-B
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1480955258-26311-1-git-send-email-imre.deak@intel.com
(cherry picked from commit a0b8a1fe34430c3a82258e8cb45f5968bdf31afd)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 7243e0b20729d372e97763617a7a9c89f29b33e1 upstream.
The calculation of SPR and SPPR doesn't round correctly at several
places which might result in baud rates that are too big. For example
with tclk_hz = 250000001 and target rate 25000000 it determined a
divider of 10 which is wrong.
Instead of fixing all the corner cases replace the calculation by an
algorithm without a loop which should even be quicker to execute apart
from being correct.
Fixes: df59fa7f4bca ("spi: orion: support armada extended baud rates")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
registration
commit 9388093db44356af911adf3d355b7544a13a63cd upstream.
Unlike clk_register_clkdev(), clk_hw_register_clkdev() doesn't check for
passed error objects from a previous registration call. Hence the caller
of clk_hw_register_*() has to check for errors before calling
clk_hw_register_clkdev*().
Make clk_hw_register_clkdev() more similar to clk_register_clkdev() by
adding this error check, removing the burden from callers that do mass
registration.
Fixes: e4f1b49bda6d6aa2 ("clkdev: Add clk_hw based registration APIs")
Fixes: 944b9a41e004534f ("clk: ls1x: Migrate to clk_hw based OF and registration APIs")
Fixes: 44ce9a9ae977736f ("MIPS: TXx9: Convert to Common Clock Framework")
Fixes: f48d947a162dfa9d ("clk: clps711x: Migrate to clk_hw based OF and registration APIs")
Fixes: b4626a7f489238a5 ("CLK: Add Loongson1C clock support")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 26242b330093fd14c2e94fb6cbdf0f482ab26576 upstream.
In case the driver registration fails, the hotplug callback is leaked.
Not fatal, because it's never invoked as there are no instances registered,
but wrong nevertheless.
Fixes: fdc15a36d84e ("bus/arm-ccn: Convert to hotplug statemachine")
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Suzuki K Poulose <suzuki.poulose@arm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 1ebb71143758f45dc0fa76e2f48429e13b16d110 upstream.
Make sure we have enough of a report structure to validate before
looking at it.
Reported-by: Benoit Camredon <benoit.camredon@airbus.com>
Tested-by: Benoit Camredon <benoit.camredon@airbus.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
[ Upstream commit 24c63bbc18e25d5d8439422aa5fd2d66390b88eb ]
Frank reported that vrf devices can be created with a table id of 0.
This breaks many of the run time table id checks and should not be
allowed. Detect this condition at create time and fail with EINVAL.
Fixes: 193125dbd8eb ("net: Introduce VRF device driver")
Reported-by: Frank Kellermann <frank.kellermann@atos.net>
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 7a18c5b9fb31a999afc62b0e60978aa896fc89e9 ]
fib_select_path does not call fib_select_multipath if oif is set in the
flow struct. For VRF use cases oif is always set, so multipath route
selection is bypassed. Use the FLOWI_FLAG_SKIP_NH_OIF to skip the oif
check similar to what is done in fib_table_lookup.
Add saddr and proto to the flow struct for the fib lookup done by the
VRF driver to better match hash computation for a flow.
Fixes: 613d09b30f8b ("net: Use VRF device index for lookups on TX")
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 0bbcc0a8fc394d01988fe0263ccf7fddb77a12c3 ]
When trying to do interface down or changing interface configuration
under heavy traffic, some of the adaptive moderation corner cases can
occur and leave a WARN_ONCE call trace in the kernel log.
Those WARN_ONCE are meant for debug only, and should have been inserted
only under debug. We avoid such call traces by removing those WARN_ONCE.
Fixes: cb3c7fd4f839 ("net/mlx5e: Support adaptive RX coalescing")
Signed-off-by: Gil Rockah <gilr@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 75dc692eda114cb234a46cb11893a9c3ea520934 ]
Pause the rx and make sure the rx fifo is empty when the autosuspend
occurs.
If the rx data comes when the driver is canceling the rx urb, the host
controller would stop getting the data from the device and continue
it after next rx urb is submitted. That is, one continuing data is
split into two different urb buffers. That let the driver take the
data as a rx descriptor, and unexpected behavior happens.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 8fb280616878b81c0790a0c33acbeec59c5711f4 ]
Split rtl8152_suspend() into rtl8152_system_suspend() and
rtl8152_rumtime_suspend().
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 2cfe8f8290bd28cf1ee67db914a6e76cf8e6437b ]
We are implementing a MDIO bus which is behind another one, so use the
nested version of the accessors to get lockdep annotations correct.
Fixes: 461cd1b03e32 ("net: dsa: bcm_sf2: Register our slave MDIO bus")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit a4c61b92b3a4cbda35bb0251a5063a68f0861b2c ]
We make the bcm_sf2 driver override ds->ops which points to
b53_switch_ops since b53_switch_alloc() did the assignent. This is all
well and good until a second b53 switch comes in, and ends up using the
bcm_sf2 operations. Make a proper local copy, substitute the ds->ops
pointer and then override the operations.
Fixes: f458995b9ad8 ("net: dsa: bcm_sf2: Utilize core B53 driver when possible")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 926d93a33e59b2729afdbad357233c17184de9d2 ]
The move from rx-handler to L3 receive handler inadvertantly dropped the
rx counters. Restore them.
Fixes: 74b20582ac38 ("net: l3mdev: Add hook in ip and ipv6")
Reported-by: Dinesh Dutt <ddutt@cumulusnetworks.com>
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 37f304d10030bb425c19099e7b955d9c3ec4cba3 ]
Disable netdev should come after it was closed, although no harm of doing it
before -hence the MLX5E_STATE_DESTROYING bit- but it is more natural this way.
Fixes: 26e59d8077a3 ("net/mlx5e: Implement mlx5e interface attach/detach callbacks")
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Reviewed-by: Mohamad Haj Yahia <mohamad@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 610e89e05c3f28a7394935aa6b91f99548c4fd3c ]
Skip setting netdev vxlan ports and netdev rx_mode on driver load
when netdev is not yet registered.
Synchronizing with netdev state is needed only on reset flow where the
netdev remains registered for the whole reset period.
This also fixes an access before initialization of net_device.addr_list_lock
- which for some reason initialized on register_netdev - where we queued
set_rx_mode work on driver load before netdev registration.
Fixes: 26e59d8077a3 ("net/mlx5e: Implement mlx5e interface attach/detach callbacks")
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Reported-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Reviewed-by: Mohamad Haj Yahia <mohamad@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit ccce1700263d8b5b219359d04180492a726cea16 ]
Need to check that VF mac address entered by the admin user is either
zero or unicast mac.
Multicast mac addresses are prohibited.
Fixes: 77256579c6b4 ('net/mlx5: E-Switch, Introduce Vport administration functions')
Signed-off-by: Mohamad Haj Yahia <mohamad@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 077b1e8069b9b74477b01d28f6b83774dc19a142 ]
We need to mask the destination mac value with the destination mac
mask when adding steering rule via ethtool.
Fixes: 1174fce8d1410 ('net/mlx5e: Support l3/l4 flow type specs in ethtool flow steering')
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit d151d73dcc99de87c63bdefebcc4cb69de1cdc40 ]
Avoid using a local variable named numa_node to avoid shadowing a public
one.
Fixes: db058a186f98 ('net/mlx5_core: Set irq affinity hints')
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 689a248df83b6032edc57e86267b4e5cc8d7174e ]
If there is pending delayed work for health recovery it must be canceled
if the device is being unloaded.
Fixes: 05ac2c0b7438 ("net/mlx5: Fix race between PCI error handlers and health work")
Signed-off-by: Daniel Jurgens <danielj@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 883371c453b937f9eb581fb4915210865982736f ]
When setting HCA capabilities, set log_max_qp to be the minimum
between the selected profile's value and the HCA limitation.
Fixes: 938fe83c8dcb ('net/mlx5_core: New device capabilities...')
Signed-off-by: Noa Osherovich <noaos@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 5701659004d68085182d2fd4199c79172165fa65 ]
There is currently a small window during which the network device registered by
stmmac can be made visible, yet all resources, including and clock and MDIO bus
have not had a chance to be set up, this can lead to the following error to
occur:
[ 473.919358] stmmaceth 0000:01:00.0 (unnamed net_device) (uninitialized):
stmmac_dvr_probe: warning: cannot get CSR clock
[ 473.919382] stmmaceth 0000:01:00.0: no reset control found
[ 473.919412] stmmac - user ID: 0x10, Synopsys ID: 0x42
[ 473.919429] stmmaceth 0000:01:00.0: DMA HW capability register supported
[ 473.919436] stmmaceth 0000:01:00.0: RX Checksum Offload Engine supported
[ 473.919443] stmmaceth 0000:01:00.0: TX Checksum insertion supported
[ 473.919451] stmmaceth 0000:01:00.0 (unnamed net_device) (uninitialized):
Enable RX Mitigation via HW Watchdog Timer
[ 473.921395] libphy: PHY stmmac-1:00 not found
[ 473.921417] stmmaceth 0000:01:00.0 eth0: Could not attach to PHY
[ 473.921427] stmmaceth 0000:01:00.0 eth0: stmmac_open: Cannot attach to
PHY (error: -19)
[ 473.959710] libphy: stmmac: probed
[ 473.959724] stmmaceth 0000:01:00.0 eth0: PHY ID 01410cc2 at 0 IRQ POLL
(stmmac-1:00) active
[ 473.959728] stmmaceth 0000:01:00.0 eth0: PHY ID 01410cc2 at 1 IRQ POLL
(stmmac-1:01)
[ 473.959731] stmmaceth 0000:01:00.0 eth0: PHY ID 01410cc2 at 2 IRQ POLL
(stmmac-1:02)
[ 473.959734] stmmaceth 0000:01:00.0 eth0: PHY ID 01410cc2 at 3 IRQ POLL
(stmmac-1:03)
Fix this by making sure that register_netdev() is the last thing being done,
which guarantees that the clock and the MDIO bus are available.
Fixes: 4bfcbd7abce2 ("stmmac: Move the mdio_register/_unregister in probe/remove")
Reported-by: Kweh, Hock Leong <hock.leong.kweh@intel.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit eb63ecc1706b3e094d0f57438b6c2067cfc299f2 ]
Locally originated traffic in a VRF fails in the presence of a POSTROUTING
rule. For example,
$ iptables -t nat -A POSTROUTING -s 11.1.1.0/24 -j MASQUERADE
$ ping -I red -c1 11.1.1.3
ping: Warning: source address might be selected on device other than red.
PING 11.1.1.3 (11.1.1.3) from 11.1.1.2 red: 56(84) bytes of data.
ping: sendmsg: Operation not permitted
Worse, the above causes random corruption resulting in a panic in random
places (I have not seen a consistent backtrace).
Call nf_reset to drop the conntrack info following the pass through the
VRF device. The nf_reset is needed on Tx but not Rx because of the order
in which NF_HOOK's are hit: on Rx the VRF device is after the real ingress
device and on Tx it is is before the real egress device. Connection
tracking should be tied to the real egress device and not the VRF device.
Fixes: 8f58336d3f78a ("net: Add ethernet header for pass through VRF device")
Fixes: 35402e3136634 ("net: Add IPv6 support to VRF device")
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit a0f37efa82253994b99623dbf41eea8dd0ba169b ]
Connection tracking with VRF is broken because the pass through the VRF
device drops the connection tracking info. Removing the call to nf_reset
allows DNAT and MASQUERADE to work across interfaces within a VRF.
Fixes: 73e20b761acf ("net: vrf: Add support for PREROUTING rules on vrf device")
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit eaa496ffaaf19591fe471a36cef366146eeb9153 upstream.
ep->mult is supposed to be set to Isochronous and
Interrupt Endapoint's multiplier value. This value
is computed from different places depending on the
link speed.
If we're dealing with HighSpeed, then it's part of
bits [12:11] of wMaxPacketSize. This case wasn't
taken into consideration before.
While at that, also make sure the ep->mult defaults
to one so drivers can use it unconditionally and
assume they'll never multiply ep->maxpacket to zero.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This reverts commit eab1c4e2d0ad4509ccb8476a604074547dc202e0 which is
commit eaa496ffaaf19591fe471a36cef366146eeb9153 upstream as it was
incorrectly backported.
Reported-by: Bin Liu <b-liu@ti.com>
Cc: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This reverts commit 98068574928f499b30f136ff57ef9a03cc575a36, which is
commit ba9f93f82abafe2552eac942ebb11c2df4f8dd7f upstream as it causes
problems.
Reported-by: Dmitry Osipenko <digetx@gmail.com>
Cc: Ping-Ke Shih <pkshih@realtek.com>
Cc: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman gregkh@linuxfoundation.org
|
|
commit 26a137e31ffe6fbfdb008554a8d9b3d55bd5c86e upstream.
If the TPM we're connecting to uses a static burst count, it will report
a burst count of zero throughout the response read. However, get_burstcount
assumes that a response of zero indicates that the TPM is not ready to
receive more data. In this case, it returns a negative error code, which
is passed on to tpm_tis_{write,read}_bytes as a u16, causing
them to read/write far too many bytes.
This patch checks for negative return codes and bails out from recv_data
and tpm_tis_send_data.
Fixes: 1107d065fdf1 (tpm_tis: Introduce intermediate layer for TPM access)
Signed-off-by: Josh Zimmerman <joshz@google.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 2ef32dee97fcf41987722a37eb6ff1a983915e99 upstream.
The previous spec version said "double Ytile planes minimum lines",
and I interpreted this as referring to what the spec calls "Y tile
minimum", but in fact it was referring to what the spec calls "Minimum
Scanlines for Y tile". I noticed that Mahesh Kumar had a different
interpretation, so I sent and email to the spec authors and got
clarification on the correct meaning. Also, BSpec was updated and
should be clear now.
Fixes: ee3d532fcb64 ("drm/i915/gen9: unconditionally apply the memory bandwidth WA")
Cc: stable@vger.kernel.org
Cc: Mahesh Kumar <mahesh1.kumar@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1478636531-6081-1-git-send-email-paulo.r.zanoni@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ee3d532fcb64872bc20be0ee58f7afdb9fa82abe upstream.
Mahesh Kumar is already working on a proper implementation for the
workaround, but while we still don't have it, let's just
unconditionally apply the workaround for everybody and we hope we can
close all those numerous bugzilla tickets. Also, I'm not sure how easy
it will be to backport the final implementation to the stable Kernels,
and this patch here is probably easier to backport.
At the present moment I still don't have confirmation that this patch
fixes any of the bugs listed below, but we should definitely try
testing all of them again.
v2: s/intel_needs_memory_bw_wa/skl_needs_memory_bw_wa/ (Lyude).
v3: Rebase (dev -> dev_priv change on ilk_wm_max_level).
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=94337
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=94605
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=94884
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=95010
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=96226
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=96828
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=97450
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=97830
Cc: Mahesh Kumar <mahesh1.kumar@intel.com>
Cc: Lyude <cpaul@redhat.com>
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Lyude <cpaul@redhat.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1476210338-9797-1-git-send-email-paulo.r.zanoni@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 1c4672ce4eeaeaadeea8adabaad21262b7172607 upstream.
We've been ignoring the poor bugzilla reporters that say PSR causes
system lockups and all other sorts of problems. The earliest bug
report is from April, so I think we can use the "revert the offending
commit if no fixes are presented within 8 months" rule here.
Fixes: 9b58e352b463 ("drm/i915: Enable PSR by default on Haswell and Broadwell.")
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=97602
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=97515
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=96736
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=96704
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=96569
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=95176
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=94985
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Jim Bride <jim.bride@linux.intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Acked-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1481662664-18986-1-git-send-email-paulo.r.zanoni@intel.com
(cherry picked from commit 2ee7dc497e348eecbb82adbb1ea9e9a7e29fe921)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 4349bd775cc8fd75cb648e3a2036a690f497de5c upstream.
We were storing viewport relative coordinates for AVIVO/DCE display
engines. However, radeon_crtc_cursor_set2 and radeon_cursor_reset pass
radeon_crtc->cursor_x/y as the x/y parameters of
radeon_cursor_move_locked, which would break if the CRTC isn't located
at (0, 0).
Cc: stable@vger.kernel.org
Signed-off-by: Michel Dänzer <michel.daenzer@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 99e5cde5eae78bef95bfe7c16ccda87fb070149b upstream.
Make sure to drop any device reference taken by vio_find_node() when
adding and removing virtual I/O slots.
Fixes: 5eeb8c63a38f ("[PATCH] PCI Hotplug: rpaphp: Move VIO registration")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 1c7de2b4ff886a45fbd2f4c3d4627e0f37a9dd77 upstream.
There is at least one Chelsio 10Gb card which uses VPD area to store some
non-standard blocks (example below). However pci_vpd_size() returns the
length of the first block only assuming that there can be only one VPD "End
Tag".
Since 4e1a635552d3 ("vfio/pci: Use kernel VPD access functions"), VFIO
blocks access beyond that offset, which prevents the guest "cxgb3" driver
from probing the device. The host system does not have this problem as its
driver accesses the config space directly without pci_read_vpd().
Add a quirk to override the VPD size to a bigger value. The maximum size
is taken from EEPROMSIZE in drivers/net/ethernet/chelsio/cxgb3/common.h.
We do not read the tag as the cxgb3 driver does as the driver supports
writing to EEPROM/VPD and when it writes, it only checks for 8192 bytes
boundary. The quirk is registered for all devices supported by the cxgb3
driver.
This adds a quirk to the PCI layer (not to the cxgb3 driver) as the cxgb3
driver itself accesses VPD directly and the problem only exists with the
vfio-pci driver (when cxgb3 is not running on the host and may not be even
loaded) which blocks accesses beyond the first block of VPD data. However
vfio-pci itself does not have quirks mechanism so we add it to PCI.
This is the controller:
Ethernet controller [0200]: Chelsio Communications Inc T310 10GbE Single Port Adapter [1425:0030]
This is what I parsed from its VPD:
===
b'\x82*\x0010 Gigabit Ethernet-SR PCI Express Adapter\x90J\x00EC\x07D76809 FN\x0746K'
0000 Large item 42 bytes; name 0x2 Identifier String
b'10 Gigabit Ethernet-SR PCI Express Adapter'
002d Large item 74 bytes; name 0x10
#00 [EC] len=7: b'D76809 '
#0a [FN] len=7: b'46K7897'
#14 [PN] len=7: b'46K7897'
#1e [MN] len=4: b'1037'
#25 [FC] len=4: b'5769'
#2c [SN] len=12: b'YL102035603V'
#3b [NA] len=12: b'00145E992ED1'
007a Small item 1 bytes; name 0xf End Tag
0c00 Large item 16 bytes; name 0x2 Identifier String
b'S310E-SR-X '
0c13 Large item 234 bytes; name 0x10
#00 [PN] len=16: b'TBD '
#13 [EC] len=16: b'110107730D2 '
#26 [SN] len=16: b'97YL102035603V '
#39 [NA] len=12: b'00145E992ED1'
#48 [V0] len=6: b'175000'
#51 [V1] len=6: b'266666'
#5a [V2] len=6: b'266666'
#63 [V3] len=6: b'2000 '
#6c [V4] len=2: b'1 '
#71 [V5] len=6: b'c2 '
#7a [V6] len=6: b'0 '
#83 [V7] len=2: b'1 '
#88 [V8] len=2: b'0 '
#8d [V9] len=2: b'0 '
#92 [VA] len=2: b'0 '
#97 [RV] len=80: b's\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00'...
0d00 Large item 252 bytes; name 0x11
#00 [VC] len=16: b'122310_1222 dp '
#13 [VD] len=16: b'610-0001-00 H1\x00\x00'
#26 [VE] len=16: b'122310_1353 fp '
#39 [VF] len=16: b'610-0001-00 H1\x00\x00'
#4c [RW] len=173: b'\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00'...
0dff Small item 0 bytes; name 0xf End Tag
10f3 Large item 13315 bytes; name 0x62
!!! unknown item name 98: b'\xd0\x03\x00@`\x0c\x08\x00\x00\x00\x00\x00\x00\x00\x00\x00'
===
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 1600f62534b7b3da7978b43b52231a54c24df287 upstream.
Mellanox devices were marked as having INTx masking ability broken. As a
result, the VFIO driver fails to start when more than one device function
is passed-through to a VM if both have the same INTx pin.
Prior to Connect-IB, Mellanox devices exposed to the operating system one
PCI function per all ports. Starting from Connect-IB, the devices are
function-per-port. When passing the second function to a VM, VFIO will
fail to start.
Exclude ConnectX-4, ConnectX4-Lx and Connect-IB from the list of Mellanox
devices marked as having broken INTx masking:
- ConnectX-4 and ConnectX4-LX firmware version is checked. If INTx
masking is supported, we unmark the broken INTx masking.
- Connect-IB does not support INTx currently so will not cause any
problem.
[bhelgaas: call pci_disable_device() always, after iounmap()]
Fixes: 11e42532ada3 ("PCI: Assume all Mellanox devices have broken INTx masking")
Signed-off-by: Noa Osherovich <noaos@mellanox.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d76d2fe05fd93673d184af77255bbbc63780f4ea upstream.
Change Mellanox's broken_intx_masking() quirk from an "all Mellanox
devices" to a quirk for listed devices only.
[bhelgaas: remove #defines, reorder to keep other quirks together]
Signed-off-by: Noa Osherovich <noaos@mellanox.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b88214ce4d7064992452765028bd50702414f15f upstream.
Convert all quirk_broken_intx_masking() quirks from HEADER to FINAL.
The quirk sets dev->broken_intx_masking, which is only used by
pci_intx_mask_supported(), which is not needed until after FINAL
quirks have been run.
[bhelgaas: changelog]
Signed-off-by: Noa Osherovich <noaos@mellanox.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a45e2611b9bbd81288d97d02ce7e74a60a698d43 upstream.
We're trying to mask out bits[23:8] while retaining [32:24, 7:0], but we're
doing the inverse. That doesn't have too much effect, since we're setting
all the [23:8] bits to 1, and the other bits are only relevant for modes
we're currently not using. But we should get this right.
Fixes: ca1989084054 ("PCI: rockchip: Fix wrong transmitted FTS count")
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 45e9320f3a4ef9588ee50a2eb1891c4bfdbb07df upstream.
The calculation of negotiated lanes is wrong: it should be shifted by
PCIE_CORE_PL_CONF_LANE_SHIFT, but it is shifted by
PCIE_CORE_PL_CONF_LANE_MASK instead. Let's fix it.
Fixes: e77f847df54c ("PCI: rockchip: Add Rockchip PCIe controller support")
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit c4a407b91f4b644145492e28723f9f880efb1da0 upstream.
We should unlock before returning this error code in vpfe_reqbufs().
Fixes: 622897da67b3 ("[media] davinci: vpfe: add v4l2 video driver support")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e2342ca832726a840ca6bd196dd2cc073815b08a upstream.
md_open() gets a counted reference on an mddev using mddev_find().
If it ends up returning an error, it must drop this reference.
There are two error paths where the reference is not dropped.
One only happens if the process is signalled and an awkward time,
which is quite unlikely.
The other was introduced recently in commit af8d8e6f0.
Change the code to ensure the drop the reference when returning an error,
and make it harded to re-introduce this sort of bug in the future.
Reported-by: Marc Smith <marc.smith@mcc.edu>
Fixes: af8d8e6f0315 ("md: changes for MD_STILL_CLOSED flag")
Signed-off-by: NeilBrown <neilb@suse.com>
Acked-by: Guoqing Jiang <gqjiang@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 82a301cb0ea2df8a5c88213094a01660067c7fb4 upstream.
Fixes: 90f5f7ad4f38("md: Wait for md_check_recovery before attempting device
removal.")
Reviewed-by: NeilBrown <neilb@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 1d74e7ed5dc1903ac081574a9b6aa94e7ba4ad45 upstream.
qcom_smd_send() should return -EAGAIN for non-blocking channels with
insufficient space, so that we can propagate this event to user space.
Fixes: 53e2822e56c7 ("rpmsg: Introduce Qualcomm SMD backend")
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 16652a936e96f5dae53c3fbd38a570497baadaa8 upstream.
We never set "ret" to RESULT_OK.
Fixes: 9f9c4180f88d ("mmc: mmc_test: add test for non-blocking transfers")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit bed570307ed78f21b77cb04a1df781dee4a8f05a upstream.
I noticed some wakeirq flakeyness with consumer drivers not using
autosuspend. For drivers not using autosuspend, the wakeirq may never
get unmasked in rpm_suspend() because of irq desc->depth.
We are configuring dedicated wakeirqs to start with IRQ_NOAUTOEN as we
naturally don't want them running until rpm_suspend() is called.
However, when a consumer driver initially calls pm_runtime_get(), we
now wrongly start with disable_irq_nosync() call on the dedicated
wakeirq that is disabled to start with.
This causes desc->depth to toggle between 1 and 2 instead of the usual
0 and 1. This can prevent enable_irq() from unmasking the wakeirq as
that only happens at desc->depth 1.
This does not necessarily show up with drivers using autosuspend as
there is time for disable_irq_nosync() before rpm_suspend() gets called
after the autosuspend timeout.
Let's fix the issue by adding wirq->status that lazily gets set on
the first rpm_suspend(). We also need PM runtime core private functions
for dev_pm_enable_wake_irq_check() and dev_pm_disable_wake_irq_check()
so we can enable the dedicated wakeirq on the first rpm_suspend().
While at it, let's also fix the comments for dev_pm_enable_wake_irq()
and dev_pm_disable_wake_irq(). Those can still be used by the consumer
drivers as needed because the IRQ core manages the interrupt usecount
for us.
Fixes: 4990d4fe327b (PM / Wakeirq: Add automated device wake IRQ handling)
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 34c535793bcbf9263cf22f8a52101f796cdfab8e upstream.
We did not implement an irq_cpu_offline callback for our irqchip, yet we
support setting a given IRQ's affinity. This resulted in interrupts
whose affinity mask included CPUs being taken offline not to work
correctly once the CPU had been put offline.
Fixes: 5f7f0317ed28 ("IRQCHIP: Add new driver for BCM7038-style level 1 interrupt controllers")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: jason@lakedaemon.net
Cc: marc.zyngier@arm.com
Cc: cernekee@gmail.com
Cc: jaedon.shin@gmail.com
Cc: ralf@linux-mips.org
Cc: justinpopo6@gmail.com
Link: http://lkml.kernel.org/r/1477948656-12966-2-git-send-email-f.fainelli@gmail.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d1d111e073840b8dbc1ae90ba3fc274736451bdc upstream.
If msi_setup_entry() fails to allocate an affinity mask, it logs a message
but continues on and allocates an MSI entry with entry->affinity == NULL.
Check for this case in pci_irq_get_affinity() so we don't try to
dereference a NULL pointer.
[bhelgaas: changelog]
Fixes: ee8d41e53efe "pci/msi: Retrieve affinity for a vector"
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
CC: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 8456066a57940b3884aa080c58b166567dc9de39 upstream.
Pass a task state as second argument to percpu_ida_alloc().
Fixes: commit 5a3ee221b543 ("sbp-target: Conversion to percpu_ida tag pre-allocation")
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Chris Boot <bootc@bootc.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a91918cd3ea11f91c68e08e1e8ce1b560447a80e upstream.
This iscsit_tpg_add_portal_group() function is only called from
lio_target_tiqn_addtpg(). Both functions free the "tpg" pointer on
error so it's a double free bug. The memory is allocated in the caller
so it should be freed in the caller and not here.
Fixes: e48354ce078c ("iscsi-target: Add iSCSI fabric support for target v4.1")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: David Disseldorp <ddiss@suse.de>
[ bvanassche: Added "Fix" at start of patch title ]
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|