summaryrefslogtreecommitdiff
path: root/drivers
AgeCommit message (Collapse)Author
2014-08-14sunsab: Fix detection of BREAK on sunsab serial consoleChristopher Alexander Tobias Schulze
[ Upstream commit fe418231b195c205701c0cc550a03f6c9758fd9e ] Fix detection of BREAK on sunsab serial console: BREAK detection was only performed when there were also serial characters received simultaneously. To handle all BREAKs correctly, the check for BREAK and the corresponding call to uart_handle_break() must also be done if count == 0, therefore duplicate this code fragment and pull it out of the loop over the received characters. Patch applies to 3.16-rc6. Signed-off-by: Christopher Alexander Tobias Schulze <cat.schulze@alice-dsl.net> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-08-14bbc-i2c: Fix BBC I2C envctrl on SunBlade 2000Christopher Alexander Tobias Schulze
[ Upstream commit 5cdceab3d5e02eb69ea0f5d8fa9181800baf6f77 ] Fix regression in bbc i2c temperature and fan control on some Sun systems that causes the driver to refuse to load due to the bbc_i2c_bussel resource not being present on the (second) i2c bus where the temperature sensors and fan control are located. (The check for the number of resources was removed when the driver was ported to a pure OF driver in mid 2008.) Signed-off-by: Christopher Alexander Tobias Schulze <cat.schulze@alice-dsl.net> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-08-14macvlan: Initialize vlan_features to turn on offload support.Vlad Yasevich
[ Upstream commit 081e83a78db9b0ae1f5eabc2dedecc865f509b98 ] Macvlan devices do not initialize vlan_features. As a result, any vlan devices configured on top of macvlans perform very poorly. Initialize vlan_features based on the vlan features of the lower-level device. Signed-off-by: Vlad Yasevich <vyasevic@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-08-14inetpeer: get rid of ip_id_countEric Dumazet
[ Upstream commit 73f156a6e8c1074ac6327e0abd1169e95eb66463 ] Ideally, we would need to generate IP ID using a per destination IP generator. linux kernels used inet_peer cache for this purpose, but this had a huge cost on servers disabling MTU discovery. 1) each inet_peer struct consumes 192 bytes 2) inetpeer cache uses a binary tree of inet_peer structs, with a nominal size of ~66000 elements under load. 3) lookups in this tree are hitting a lot of cache lines, as tree depth is about 20. 4) If server deals with many tcp flows, we have a high probability of not finding the inet_peer, allocating a fresh one, inserting it in the tree with same initial ip_id_count, (cf secure_ip_id()) 5) We garbage collect inet_peer aggressively. IP ID generation do not have to be 'perfect' Goal is trying to avoid duplicates in a short period of time, so that reassembly units have a chance to complete reassembly of fragments belonging to one message before receiving other fragments with a recycled ID. We simply use an array of generators, and a Jenkin hash using the dst IP as a key. ipv6_select_ident() is put back into net/ipv6/ip6_output.c where it belongs (it is only used from this file) secure_ip_id() and secure_ipv6_id() no longer are needed. Rename ip_select_ident_more() to ip_select_ident_segs() to avoid unnecessary decrement/increment of the number of segments. Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-08-07scsi: handle flush errors properlyJames Bottomley
commit 89fb4cd1f717a871ef79fa7debbe840e3225cd54 upstream. Flush commands don't transfer data and thus need to be special cased in the I/O completion handler so that we can propagate errors to the block layer and filesystem. Signed-off-by: James Bottomley <JBottomley@Parallels.com> Reported-by: Steven Haber <steven@qumulo.com> Tested-by: Steven Haber <steven@qumulo.com> Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-07-31ahci: add support for the Promise FastTrak TX8660 SATA HBA (ahci mode)Romain Degez
commit b32bfc06aefab61acc872dec3222624e6cd867ed upstream. Add support of the Promise FastTrak TX8660 SATA HBA in ahci mode by registering the board in the ahci_pci_tbl[]. Note: this HBA also provide a hardware RAID mode when activated in BIOS but specific drivers from the manufacturer are required in this case. Signed-off-by: Romain Degez <romain.degez@gmail.com> Tested-by: Romain Degez <romain.degez@gmail.com> Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-07-31libata: introduce ata_host->n_tags to avoid oops on SAS controllersTejun Heo
commit 1a112d10f03e83fb3a2fdc4c9165865dec8a3ca6 upstream. 1871ee134b73 ("libata: support the ata host which implements a queue depth less than 32") directly used ata_port->scsi_host->can_queue from ata_qc_new() to determine the number of tags supported by the host; unfortunately, SAS controllers doing SATA don't initialize ->scsi_host leading to the following oops. BUG: unable to handle kernel NULL pointer dereference at 0000000000000058 IP: [<ffffffff814e0618>] ata_qc_new_init+0x188/0x1b0 PGD 0 Oops: 0002 [#1] SMP Modules linked in: isci libsas scsi_transport_sas mgag200 drm_kms_helper ttm CPU: 1 PID: 518 Comm: udevd Not tainted 3.16.0-rc6+ #62 Hardware name: Intel Corporation S2600CO/S2600CO, BIOS SE5C600.86B.02.02.0002.122320131210 12/23/2013 task: ffff880c1a00b280 ti: ffff88061a000000 task.ti: ffff88061a000000 RIP: 0010:[<ffffffff814e0618>] [<ffffffff814e0618>] ata_qc_new_init+0x188/0x1b0 RSP: 0018:ffff88061a003ae8 EFLAGS: 00010012 RAX: 0000000000000001 RBX: ffff88000241ca80 RCX: 00000000000000fa RDX: 0000000000000020 RSI: 0000000000000020 RDI: ffff8806194aa298 RBP: ffff88061a003ae8 R08: ffff8806194a8000 R09: 0000000000000000 R10: 0000000000000000 R11: ffff88000241ca80 R12: ffff88061ad58200 R13: ffff8806194aa298 R14: ffffffff814e67a0 R15: ffff8806194a8000 FS: 00007f3ad7fe3840(0000) GS:ffff880627620000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000000000000058 CR3: 000000061a118000 CR4: 00000000001407e0 Stack: ffff88061a003b20 ffffffff814e96e1 ffff88000241ca80 ffff88061ad58200 ffff8800b6bf6000 ffff880c1c988000 ffff880619903850 ffff88061a003b68 ffffffffa0056ce1 ffff88061a003b48 0000000013d6e6f8 ffff88000241ca80 Call Trace: [<ffffffff814e96e1>] ata_sas_queuecmd+0xa1/0x430 [<ffffffffa0056ce1>] sas_queuecommand+0x191/0x220 [libsas] [<ffffffff8149afee>] scsi_dispatch_cmd+0x10e/0x300 [<ffffffff814a3bc5>] scsi_request_fn+0x2f5/0x550 [<ffffffff81317613>] __blk_run_queue+0x33/0x40 [<ffffffff8131781a>] queue_unplugged+0x2a/0x90 [<ffffffff8131ceb4>] blk_flush_plug_list+0x1b4/0x210 [<ffffffff8131d274>] blk_finish_plug+0x14/0x50 [<ffffffff8117eaa8>] __do_page_cache_readahead+0x198/0x1f0 [<ffffffff8117ee21>] force_page_cache_readahead+0x31/0x50 [<ffffffff8117ee7e>] page_cache_sync_readahead+0x3e/0x50 [<ffffffff81172ac6>] generic_file_read_iter+0x496/0x5a0 [<ffffffff81219897>] blkdev_read_iter+0x37/0x40 [<ffffffff811e307e>] new_sync_read+0x7e/0xb0 [<ffffffff811e3734>] vfs_read+0x94/0x170 [<ffffffff811e43c6>] SyS_read+0x46/0xb0 [<ffffffff811e33d1>] ? SyS_lseek+0x91/0xb0 [<ffffffff8171ee29>] system_call_fastpath+0x16/0x1b Code: 00 00 00 88 50 29 83 7f 08 01 19 d2 83 e2 f0 83 ea 50 88 50 34 c6 81 1d 02 00 00 40 c6 81 17 02 00 00 00 5d c3 66 0f 1f 44 00 00 <89> 14 25 58 00 00 00 Fix it by introducing ata_host->n_tags which is initialized to ATA_MAX_QUEUE - 1 in ata_host_init() for SAS controllers and set to scsi_host_template->can_queue in ata_host_register() for !SAS ones. As SAS hosts are never registered, this will give them the same ATA_MAX_QUEUE - 1 as before. Note that we can't use scsi_host->can_queue directly for SAS hosts anyway as they can go higher than the libata maximum. Signed-off-by: Tejun Heo <tj@kernel.org> Reported-by: Mike Qiu <qiudayu@linux.vnet.ibm.com> Reported-by: Jesse Brandeburg <jesse.brandeburg@gmail.com> Reported-by: Peter Hurley <peter@hurleysoftware.com> Reported-by: Peter Zijlstra <peterz@infradead.org> Tested-by: Alexey Kardashevskiy <aik@ozlabs.ru> Fixes: 1871ee134b73 ("libata: support the ata host which implements a queue depth less than 32") Cc: Kevin Hao <haokexin@gmail.com> Cc: Dan Williams <dan.j.williams@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-07-31libata: support the ata host which implements a queue depth less than 32Kevin Hao
commit 1871ee134b73fb4cadab75752a7152ed2813c751 upstream. The sata on fsl mpc8315e is broken after the commit 8a4aeec8d2d6 ("libata/ahci: accommodate tag ordered controllers"). The reason is that the ata controller on this SoC only implement a queue depth of 16. When issuing the commands in tag order, all the commands in tag 16 ~ 31 are mapped to tag 0 unconditionally and then causes the sata malfunction. It makes no senses to use a 32 queue in software while the hardware has less queue depth. So consider the queue depth implemented by the hardware when requesting a command tag. Fixes: 8a4aeec8d2d6 ("libata/ahci: accommodate tag ordered controllers") Signed-off-by: Kevin Hao <haokexin@gmail.com> Acked-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-07-28iommu/vt-d: Disable translation if already enabledTakao Indoh
commit 3a93c841c2b3b14824f7728dd74bd00a1cedb806 upstream. This patch disables translation(dma-remapping) before its initialization if it is already enabled. This is needed for kexec/kdump boot. If dma-remapping is enabled in the first kernel, it need to be disabled before initializing its page table during second kernel boot. Wei Hu also reported that this is needed when second kernel boots with intel_iommu=off. Basically iommu->gcmd is used to know whether translation is enabled or disabled, but it is always zero at boot time even when translation is enabled since iommu->gcmd is initialized without considering such a case. Therefor this patch synchronizes iommu->gcmd value with global command register when iommu structure is allocated. Signed-off-by: Takao Indoh <indou.takao@jp.fujitsu.com> Signed-off-by: Joerg Roedel <joro@8bytes.org> [wyj: Backported to 3.4: adjust context] Signed-off-by: Yijing Wang <wangyijing@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-07-28drm/radeon: avoid leaking edid dataAlex Deucher
commit 0ac66effe7fcdee55bda6d5d10d3372c95a41920 upstream. In some cases we fetch the edid in the detect() callback in order to determine what sort of monitor is connected. If that happens, don't fetch the edid again in the get_modes() callback or we will leak the edid. Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-07-28mwifiex: fix Tx timeout issueAmitkumar Karwar
commit d76744a93246eccdca1106037e8ee29debf48277 upstream. https://bugzilla.kernel.org/show_bug.cgi?id=70191 https://bugzilla.kernel.org/show_bug.cgi?id=77581 It is observed that sometimes Tx packet is downloaded without adding driver's txpd header. This results in firmware parsing garbage data as packet length. Sometimes firmware is unable to read the packet if length comes out as invalid. This stops further traffic and timeout occurs. The root cause is uninitialized fields in tx_info(skb->cb) of packet used to get garbage values. In this case if MWIFIEX_BUF_FLAG_REQUEUED_PKT flag is mistakenly set, txpd header was skipped. This patch makes sure that tx_info is correctly initialized to fix the problem. Reported-by: Andrew Wiley <wiley.andrew.j@gmail.com> Reported-by: Linus Gasser <list@markas-al-nour.org> Reported-by: Michael Hirsch <hirsch@teufel.de> Tested-by: Xinming Hu <huxm@marvell.com> Signed-off-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: Maithili Hinge <maithili@marvell.com> Signed-off-by: Avinash Patil <patila@marvell.com> Signed-off-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-07-28sunvnet: clean up objects created in vnet_new() on vnet_exit()Sowmini Varadhan
[ Upstream commit a4b70a07ed12a71131cab7adce2ce91c71b37060 ] Nothing cleans up the objects created by vnet_new(), they are completely leaked. vnet_exit(), after doing the vio_unregister_driver() to clean up ports, should call a helper function that iterates over vnet_list and cleans up those objects. This includes unregister_netdevice() as well as free_netdev(). Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com> Acked-by: Dave Kleikamp <dave.kleikamp@oracle.com> Reviewed-by: Karl Volz <karl.volz@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-07-28net: pppoe: use correct channel MTU when using Multilink PPPChristoph Schulz
[ Upstream commit a8a3e41c67d24eb12f9ab9680cbb85e24fcd9711 ] The PPP channel MTU is used with Multilink PPP when ppp_mp_explode() (see ppp_generic module) tries to determine how big a fragment might be. According to RFC 1661, the MTU excludes the 2-byte PPP protocol field, see the corresponding comment and code in ppp_mp_explode(): /* * hdrlen includes the 2-byte PPP protocol field, but the * MTU counts only the payload excluding the protocol field. * (RFC1661 Section 2) */ mtu = pch->chan->mtu - (hdrlen - 2); However, the pppoe module *does* include the PPP protocol field in the channel MTU, which is wrong as it causes the PPP payload to be 1-2 bytes too big under certain circumstances (one byte if PPP protocol compression is used, two otherwise), causing the generated Ethernet packets to be dropped. So the pppoe module has to subtract two bytes from the channel MTU. This error only manifests itself when using Multilink PPP, as otherwise the channel MTU is not used anywhere. In the following, I will describe how to reproduce this bug. We configure two pppd instances for multilink PPP over two PPPoE links, say eth2 and eth3, with a MTU of 1492 bytes for each link and a MRRU of 2976 bytes. (This MRRU is computed by adding the two link MTUs and subtracting the MP header twice, which is 4 bytes long.) The necessary pppd statements on both sides are "multilink mtu 1492 mru 1492 mrru 2976". On the client side, we additionally need "plugin rp-pppoe.so eth2" and "plugin rp-pppoe.so eth3", respectively; on the server side, we additionally need to start two pppoe-server instances to be able to establish two PPPoE sessions, one over eth2 and one over eth3. We set the MTU of the PPP network interface to the MRRU (2976) on both sides of the connection in order to make use of the higher bandwidth. (If we didn't do that, IP fragmentation would kick in, which we want to avoid.) Now we send a ICMPv4 echo request with a payload of 2948 bytes from client to server over the PPP link. This results in the following network packet: 2948 (echo payload) + 8 (ICMPv4 header) + 20 (IPv4 header) --------------------- 2976 (PPP payload) These 2976 bytes do not exceed the MTU of the PPP network interface, so the IP packet is not fragmented. Now the multilink PPP code in ppp_mp_explode() prepends one protocol byte (0x21 for IPv4), making the packet one byte bigger than the negotiated MRRU. So this packet would have to be divided in three fragments. But this does not happen as each link MTU is assumed to be two bytes larger. So this packet is diveded into two fragments only, one of size 1489 and one of size 1488. Now we have for that bigger fragment: 1489 (PPP payload) + 4 (MP header) + 2 (PPP protocol field for the MP payload (0x3d)) + 6 (PPPoE header) -------------------------- 1501 (Ethernet payload) This packet exceeds the link MTU and is discarded. If one configures the link MTU on the client side to 1501, one can see the discarded Ethernet frames with tcpdump running on the client. A ping -s 2948 -c 1 192.168.15.254 leads to the smaller fragment that is correctly received on the server side: (tcpdump -vvvne -i eth3 pppoes and ppp proto 0x3d) 52:54:00:ad:87:fd > 52:54:00:79:5c:d0, ethertype PPPoE S (0x8864), length 1514: PPPoE [ses 0x3] MLPPP (0x003d), length 1494: seq 0x000, Flags [end], length 1492 and to the bigger fragment that is not received on the server side: (tcpdump -vvvne -i eth2 pppoes and ppp proto 0x3d) 52:54:00:70:9e:89 > 52:54:00:5d:6f:b0, ethertype PPPoE S (0x8864), length 1515: PPPoE [ses 0x5] MLPPP (0x003d), length 1495: seq 0x000, Flags [begin], length 1493 With the patch below, we correctly obtain three fragments: 52:54:00:ad:87:fd > 52:54:00:79:5c:d0, ethertype PPPoE S (0x8864), length 1514: PPPoE [ses 0x1] MLPPP (0x003d), length 1494: seq 0x000, Flags [begin], length 1492 52:54:00:70:9e:89 > 52:54:00:5d:6f:b0, ethertype PPPoE S (0x8864), length 1514: PPPoE [ses 0x1] MLPPP (0x003d), length 1494: seq 0x000, Flags [none], length 1492 52:54:00:ad:87:fd > 52:54:00:79:5c:d0, ethertype PPPoE S (0x8864), length 27: PPPoE [ses 0x1] MLPPP (0x003d), length 7: seq 0x000, Flags [end], length 5 And the ICMPv4 echo request is successfully received at the server side: IP (tos 0x0, ttl 64, id 21925, offset 0, flags [DF], proto ICMP (1), length 2976) 192.168.222.2 > 192.168.15.254: ICMP echo request, id 30530, seq 0, length 2956 The bug was introduced in commit c9aa6895371b2a257401f59d3393c9f7ac5a8698 ("[PPPOE]: Advertise PPPoE MTU") from the very beginning. This patch applies to 3.10 upwards but the fix can be applied (with minor modifications) to kernels as old as 2.6.32. Signed-off-by: Christoph Schulz <develop@kristov.de> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-07-28be2net: set EQ DB clear-intr bit in be_open()Suresh Reddy
[ Upstream commit 4cad9f3b61c7268fa89ab8096e23202300399b5d ] On BE3, if the clear-interrupt bit of the EQ doorbell is not set the first time it is armed, ocassionally we have observed that the EQ doesn't raise anymore interrupts even if it is in armed state. This patch fixes this by setting the clear-interrupt bit when EQs are armed for the first time in be_open(). Signed-off-by: Suresh Reddy <Suresh.Reddy@emulex.com> Signed-off-by: Sathya Perla <sathya.perla@emulex.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-07-17ACPI / battery: Retry to get battery information if failed during probingLan Tianyu
commit 75646e758a0ecbed5024454507d5be5b9ea9dcbf upstream. Some machines (eg. Lenovo Z480) ECs are not stable during boot up and causes battery driver fails to be loaded due to failure of getting battery information from EC sometimes. After several retries, the operation will work. This patch is to retry to get battery information 5 times if the first try fails. [ backport to 3.14.5: removed second parameter in acpi_battery_update(), introduced by the commit 9e50bc14a7f58b5d8a55973b2d69355852ae2dae (ACPI / battery: Accelerate battery resume callback)] [naszar <naszar@ya.ru>: backport to 3.14.5] Link: https://bugzilla.kernel.org/show_bug.cgi?id=75581 Reported-and-tested-by: naszar <naszar@ya.ru> Cc: All applicable <stable@vger.kernel.org> Signed-off-by: Lan Tianyu <tianyu.lan@intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-07-17drm/radeon: stop poisoning the GART TLBChristian König
commit 0986c1a55ca64b44ee126a2f719a6e9f28cbe0ed upstream. When we set the valid bit on invalid GART entries they are loaded into the TLB when an adjacent entry is loaded. This poisons the TLB with invalid entries which are sometimes not correctly removed on TLB flush. For stable inclusion the patch probably needs to be modified a bit. Signed-off-by: Christian König <christian.koenig@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-07-17hwmon: (adm1029) Ensure the fan_div cache is updated in set_fan_divAxel Lin
commit 1035a9e3e9c76b64a860a774f5b867d28d34acc2 upstream. Writing to fanX_div does not clear the cache. As a result, reading from fanX_div may return the old value for up to two seconds after writing a new value. This patch ensures the fan_div cache is updated in set_fan_div(). Reported-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Axel Lin <axel.lin@ingics.com> Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-07-17hwmon: (amc6821) Fix permissions for temp2_inputAxel Lin
commit df86754b746e9a0ff6f863f690b1c01d408e3cdc upstream. temp2_input should not be writable, fix it. Reported-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Axel Lin <axel.lin@ingics.com> Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-07-17USB: ftdi_sio: Add extra PID.Bert Vermeulen
commit 5a7fbe7e9ea0b1b9d7ffdba64db1faa3a259164c upstream. This patch adds PID 0x0003 to the VID 0x128d (Testo). At least the Testo 435-4 uses this, likely other gear as well. Signed-off-by: Bert Vermeulen <bert@biot.com> Cc: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-07-17USB: cp210x: add support for Corsair usb dongleAndras Kovacs
commit b9326057a3d8447f5d2e74a7b521ccf21add2ec0 upstream. Corsair USB Dongles are shipped with Corsair AXi series PSUs. These are cp210x serial usb devices, so make driver detect these. I have a program, that can get information from these PSUs. Tested with 2 different dongles shipped with Corsair AX860i and AX1200i units. Signed-off-by: Andras Kovacs <andras@sth.sze.hu> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-07-17usb: option: Add ID for Telewell TW-LTE 4G v2Bernd Wachter
commit 3d28bd840b2d3981cd28caf5fe1df38f1344dd60 upstream. Add ID of the Telewell 4G v2 hardware to option driver to get legacy serial interface working Signed-off-by: Bernd Wachter <bernd.wachter@jolla.com> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-07-09ACPI video: ignore BIOS backlight value for HP dm4Gustavo Maciel Dias Vieira
commit 771d09b3c4c45d4d534a83a68e6331b97fd82e15 upstream. On a HP Pavilion dm4 laptop the BIOS sets minimum backlight on boot, completely dimming the screen. Ignore this initial value for this machine. Signed-off-by: Gustavo Maciel Dias Vieira <gustavo@sagui.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk> [wyj: Backported to 3.4: adjust context] Signed-off-by: Yijing Wang <wangyijing@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-07-09Staging: bcm: Add two products and remove an existing product.Kevin McKinney
commit 4f29ef050848245f7c180b95ccf67dfcd76b1fd8 upstream. This patch adds two new products and modifies the device id table to include them. In addition, product of 0xbccd - BCM_USB_PRODUCT_ID_SM250 is removed because Beceem, ZTE, Sprint use this id for block devices. Reported-by: Muhammad Minhazul Haque <mdminhazulhaque@gmail.com> Signed-off-by: Kevin McKinney <klmckinney1@gmail.com> [bwh: Backported to 3.2: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Cc: Yijing Wang <wangyijing@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-07-09Staging: bcm: Create and initialize new device id in InterfaceInitKevin McKinney
commit e66fc1fba248738d32f3b64508f9ef1176d9e767 upstream. This patch create and initalizes a new device id of 0x172 as reported by Rinat Camalov <richman1000000d@gmail.com>. In addition, a comment is added to the potential invalid existing device id. Reported-by: Rinat Camalov <richman1000000d@gmail.com> Signed-off-by: Kevin McKinney <klmckinney1@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> [bwh: Backported to 3.2: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Cc: Yijing Wang <wangyijing@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-07-09staging: wlags49_h2: buffer overflow setting station nameDan Carpenter
commit b5e2f339865fb443107e5b10603e53bbc92dc054 upstream. We need to check the length parameter before doing the memcpy(). I've actually changed it to strlcpy() as well so that it's NUL terminated. You need CAP_NET_ADMIN to trigger these so it's not the end of the world. Reported-by: Nico Golde <nico@ngolde.de> Reported-by: Fabian Yamaguchi <fabs@goesec.de> Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> [bwh: Backported to 3.2: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Cc: Yijing Wang <wangyijing@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-07-09staging: comedi: fix a race between do_cmd_ioctl() and read/writeIan Abbott
commit 4b18f08be01a7b3c7b6df497137b6e3cb28adaa3 upstream. `do_cmd_ioctl()` is called with the comedi device's mutex locked to process the `COMEDI_CMD` ioctl to set up comedi's asynchronous command handling on a comedi subdevice. `comedi_read()` and `comedi_write()` are the `read` and `write` handlers for the comedi device, but do not lock the mutex (for performance reasons, as some things can hold the mutex for quite a long time). There is a race condition if `comedi_read()` or `comedi_write()` is running at the same time and for the same file object and comedi subdevice as `do_cmd_ioctl()`. `do_cmd_ioctl()` sets the subdevice's `busy` pointer to the file object way before it sets the `SRF_RUNNING` flag in the subdevice's `runflags` member. `comedi_read() and `comedi_write()` check the subdevice's `busy` pointer is pointing to the current file object, then if the `SRF_RUNNING` flag is not set, will call `do_become_nonbusy()` to shut down the asyncronous command. Bad things can happen if the asynchronous command is being shutdown and set up at the same time. To prevent the race, don't set the `busy` pointer until after the `SRF_RUNNING` flag has been set. Also, make sure the mutex is held in `comedi_read()` and `comedi_write()` while calling `do_become_nonbusy()` in order to avoid moving the race condition to a point within that function. Change some error handling `goto cleanup` statements in `do_cmd_ioctl()` to simple `return -ERRFOO` statements as a result of changing when the `busy` pointer is set. Signed-off-by: Ian Abbott <abbotti@mev.co.uk> [bwh: Backported to 3.2: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Cc: Yijing Wang <wangyijing@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-07-09staging: comedi: das08: Correct AI encoding for das08jr-16-aoIan Abbott
commit e6391a182865efc896cb2a8d79e07b7ac2f45b48 upstream. The element of `das08_boards[]` for the 'das08jr-16-ao' board has the `ai_encoding` member set to `das08_encode12`. It should be set to `das08_encode16` same as the 'das08jr/16' board. After all, this board has 16-bit AI resolution. The description of the A/D LSB register at offset 0 seems incorrect in the user manual "cio-das08jr-16-ao.pdf" as it implies that the AI resolution is only 12 bits. The diagrams of the A/D LSB and MSB registers show 15 data bits and a sign bit, which matches what the software expects for the `das08_encode16` AI encoding method. Signed-off-by: Ian Abbott <abbotti@mev.co.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> [bwh: Backported to 3.2: adjust indentation] Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Cc: Yijing Wang <wangyijing@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-07-09ACPI video: ignore BIOS initial backlight value for HP 1000Alex Hung
commit 4ef366c583d6180b1c951147869ee5a3038834f2 upstream. On HP 1000 lapops, BIOS reports minimum backlight on boot and causes backlight to dim completely. This ignores the initial backlight values and set to max brightness. References:: https://bugs.launchpad.net/bugs/1167760 Signed-off-by: Alex Hung <alex.hung@canonical.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Cc: Yijing Wang <wangyijing@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-07-09ACPI / video: Add "Asus UL30A" to ACPI video detect blacklistBastian Triller
commit c8f6d8351ba8c89d5cd4c562552ec7ec29274e31 upstream. Like on UL30VT, the ACPI video driver can't control backlight correctly on Asus UL30A. Vendor driver (asus-laptop) can work. This patch is to add "Asus UL30A" to ACPI video detect blacklist in order to use asus-laptop for video control on the "Asus UL30A" rather than ACPI video driver. Signed-off-by: Bastian Triller <bastian.triller@gmail.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Cc: Yijing Wang <wangyijing@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-07-09ACPI / video: Add "Asus UL30VT" to ACPI video detect blacklistLan Tianyu
commit d0c2ce16bec0afa6013b4c5220ca4c9c67210215 upstream. The ACPI video driver can't control backlight correctly on Asus UL30VT. Vendor driver (asus-laptop) can work. This patch is to add "Asus UL30VT" to ACPI video detect blacklist in order to use asus-laptop for video control on the "Asus UL30VT" rather than ACPI video driver. References: https://bugzilla.kernel.org/show_bug.cgi?id=32592 Reported-by: Alex Williamson <alex.williamson@redhat.com> Signed-off-by: Lan Tianyu <tianyu.lan@intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Cc: Yijing Wang <wangyijing@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-07-09acpi/video_detect: blacklist samsung x360Corentin Chary
commit 084940d5b101e9ca91a689eb5048151b14076839 upstream. On Samsung X360, the BIOS will set a flag (VDRV) if the generic ACPI backlight device is used. This flag will definitively break the backlight interface (even the vendor interface) untill next reboot. It's why we should prevent video.ko from being used here and we can't rely on a later call to acpi_video_unregister(). Signed-off-by: Corentin Chary <corentin.chary@gmail.com> Signed-off-by: Matthew Garrett <mjg@redhat.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Cc: Yijing Wang <wangyijing@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-07-09sym53c8xx_2: Set DID_REQUEUE return code when aborting squeueMikulas Patocka
commit fd1232b214af43a973443aec6a2808f16ee5bf70 upstream. This patch fixes I/O errors with the sym53c8xx_2 driver when the disk returns QUEUE FULL status. When the controller encounters an error (including QUEUE FULL or BUSY status), it aborts all not yet submitted requests in the function sym_dequeue_from_squeue. This function aborts them with DID_SOFT_ERROR. If the disk has full tag queue, the request that caused the overflow is aborted with QUEUE FULL status (and the scsi midlayer properly retries it until it is accepted by the disk), but the sym53c8xx_2 driver aborts the following requests with DID_SOFT_ERROR --- for them, the midlayer does just a few retries and then signals the error up to sd. The result is that disk returning QUEUE FULL causes request failures. The error was reproduced on 53c895 with COMPAQ BD03685A24 disk (rebranded ST336607LC) with command queue 48 or 64 tags. The disk has 64 tags, but under some access patterns it return QUEUE FULL when there are less than 64 pending tags. The SCSI specification allows returning QUEUE FULL anytime and it is up to the host to retry. Signed-off-by: Mikulas Patocka <mpatocka@redhat.com> Cc: Matthew Wilcox <matthew@wil.cx> Cc: James Bottomley <JBottomley@Parallels.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-07-09md: flush writes before starting a recovery.NeilBrown
commit 133d4527eab8d199a62eee6bd433f0776842df2e upstream. When we write to a degraded array which has a bitmap, we make sure the relevant bit in the bitmap remains set when the write completes (so a 're-add' can quickly rebuilt a temporarily-missing device). If, immediately after such a write starts, we incorporate a spare, commence recovery, and skip over the region where the write is happening (because the 'needs recovery' flag isn't set yet), then that write will not get to the new device. Once the recovery finishes the new device will be trusted, but will have incorrect data, leading to possible corruption. We cannot set the 'needs recovery' flag when we start the write as we do not know easily if the write will be "degraded" or not. That depends on details of the particular raid level and particular write request. This patch fixes a corruption issue of long standing and so it suitable for any -stable kernel. It applied correctly to 3.0 at least and will minor editing to earlier kernels. Reported-by: Bill <billstuff2001@sbcglobal.net> Tested-by: Bill <billstuff2001@sbcglobal.net> Link: http://lkml.kernel.org/r/53A518BB.60709@sbcglobal.net Signed-off-by: NeilBrown <neilb@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-07-09b43: fix frequency reported on G-PHY with /new/ firmwareRafał Miłecki
commit 2fc68eb122c7ea6cd5be1fe7d6650c0beb2f4f40 upstream. Support for firmware rev 508+ was added years ago, but we never noticed it reports channel in a different way for G-PHY devices. Instead of offset from 2400 MHz it simply passes channel id (AKA hw_value). So far it was (most probably) affecting monitor mode users only, but the following recent commit made it noticeable for quite everybody: commit 3afc2167f60a327a2c1e1e2600ef209a3c2b75b7 Author: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Date: Tue Mar 4 16:50:13 2014 +0200 cfg80211/mac80211: ignore signal if the frame was heard on wrong channel Reported-by: Aaro Koskinen <aaro.koskinen@iki.fi> Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-07-09drm/vmwgfx: Fix incorrect write to read-only register v2:Thomas Hellstrom
commit 4e578080ed3262ed2c3985868539bc66218d25c0 upstream. Commit "drm/vmwgfx: correct fb_fix_screeninfo.line_length", while fixing a vmwgfx fbdev bug, also writes the pitch to a supposedly read-only register: SVGA_REG_BYTES_PER_LINE, while it should be (and also in fact is) written to SVGA_REG_PITCHLOCK. This patch is Cc'd stable because of the unknown effects writing to this register might have, particularly on older device versions. v2: Updated log message. Cc: Christopher Friedt <chrisfriedt@gmail.com> Tested-by: Christopher Friedt <chrisfriedt@gmail.com> Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com> Reviewed-by: Jakob Bornecrantz <jakob@vmware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-07-09drm/radeon/atom: fix dithering on certain panelsAlex Deucher
commit 642528355c694f5ed68f6bff9ff520326a249f99 upstream. We need to specify the encoder mode as LVDS for eDP when using the Crtc_Source atom table in order to properly set up the FMT hardware. bug: https://bugs.freedesktop.org/show_bug.cgi?id=73911 Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-07-09drm/radeon: fix typo in radeon_connector_is_dp12_capable()Alex Deucher
commit af5d36539dfe043f1cf0f8b7334d6bb12cd14e75 upstream. We were checking the ext clock rather than the display clock. Noticed by ArtForz on IRC. Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-07-09drm/radeon: only apply hdmi bpc pll flags when encoder mode is hdmiAlex Deucher
commit 7d5ab3009a8ca777174f6f469277b3922d56fd4b upstream. May fix display issues with non-HDMI displays. Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-07-09mtd: pxa3xx_nand: make the driver work on big-endian systemsThomas Petazzoni
commit b7e460624f0f3c31150f3b09e75b0d009e22ba5f upstream. The pxa3xx_nand driver currently uses __raw_writel() and __raw_readl() to access I/O registers. However, those functions do not do any endianness swapping, which means that they won't work when the CPU runs in big-endian but the I/O registers are little endian, which is the common situation for ARM systems running big endian. Since __raw_writel() and __raw_readl() do not include any memory barriers and the pxa3xx_nand driver can only be compiled for ARM platforms, the closest I/o accessors functions that do endianess swapping are writel_relaxed() and readl_relaxed(). This patch has been verified to work on Armada XP GP: without the patch, the NAND is not detected when the kernel runs big endian while it is properly detected when the kernel runs little endian. With the patch applied, the NAND is properly detected in both situations (little and big endian). Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Signed-off-by: Brian Norris <computersforpeace@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-07-09rt2x00: fix rfkill regression on rt2500pciStanislaw Gruszka
commit 616a8394b5df8c88f4dd416f4527439a4e365034 upstream. As reported by Niels, starting rfkill polling during device probe (commit e2bc7c5, generally sane change) broke rfkill on rt2500pci device. I considered that bug as some initalization issue, which should be fixed on rt2500pci specific code. But after several attempts (see bug report for details) we fail to find working solution. Hence I decided to revert to old behaviour on rt2500pci to fix regression. Additionally patch also unregister rfkill on device remove instead of ifconfig down, what was another issue introduced by bad commit. Bug report: https://bugzilla.kernel.org/show_bug.cgi?id=73821 Fixes: e2bc7c5f3cb8 ("rt2x00: Fix rfkill_polling register function.") Bisected-by: Niels <nille0386@googlemail.com> Reported-and-tested-by: Niels <nille0386@googlemail.com> Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-07-09rt2x00: disable TKIP on USBStanislaw Gruszka
commit 8edcb0ba0d56f5914eef11eda6db8bfe74eb9ca8 upstream. On USB we can not get atomically TKIP key. We have to disable support for TKIP acceleration on USB hardware to avoid bug as showed bellow. [ 860.827243] BUG: scheduling while atomic: hostapd/3397/0x00000002 <snip> [ 860.827280] Call Trace: [ 860.827282] [<ffffffff81682ea6>] dump_stack+0x4d/0x66 [ 860.827284] [<ffffffff8167eb9b>] __schedule_bug+0x47/0x55 [ 860.827285] [<ffffffff81685bb3>] __schedule+0x733/0x7b0 [ 860.827287] [<ffffffff81685c59>] schedule+0x29/0x70 [ 860.827289] [<ffffffff81684f8a>] schedule_timeout+0x15a/0x2b0 [ 860.827291] [<ffffffff8105ac50>] ? ftrace_raw_event_tick_stop+0xc0/0xc0 [ 860.827294] [<ffffffff810c13c2>] ? __module_text_address+0x12/0x70 [ 860.827296] [<ffffffff81686823>] wait_for_completion_timeout+0xb3/0x140 [ 860.827298] [<ffffffff81080fc0>] ? wake_up_state+0x20/0x20 [ 860.827301] [<ffffffff814d5b3d>] usb_start_wait_urb+0x7d/0x150 [ 860.827303] [<ffffffff814d5cd5>] usb_control_msg+0xc5/0x110 [ 860.827305] [<ffffffffa02fb0c6>] rt2x00usb_vendor_request+0xc6/0x160 [rt2x00usb] [ 860.827307] [<ffffffffa02fb215>] rt2x00usb_vendor_req_buff_lock+0x75/0x150 [rt2x00usb] [ 860.827309] [<ffffffffa02fb393>] rt2x00usb_vendor_request_buff+0xa3/0xe0 [rt2x00usb] [ 860.827311] [<ffffffffa023d1a3>] rt2x00usb_register_multiread+0x33/0x40 [rt2800usb] [ 860.827314] [<ffffffffa05805f9>] rt2800_get_tkip_seq+0x39/0x50 [rt2800lib] [ 860.827321] [<ffffffffa0480f88>] ieee80211_get_key+0x218/0x2a0 [mac80211] [ 860.827322] [<ffffffff815cc68c>] ? __nlmsg_put+0x6c/0x80 [ 860.827329] [<ffffffffa051b02e>] nl80211_get_key+0x22e/0x360 [cfg80211] Reported-and-tested-by: Peter Wu <lekensteyn@gmail.com> Reported-and-tested-by: Pontus Fuchs <pontus.fuchs@gmail.com> Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-07-09usb: gadget: f_fs: fix NULL pointer dereference when there are no stringsMichal Nazarewicz
commit f0688c8b81d2ea239c3fb0b848f623b579238d99 upstream. If the descriptors do not need any strings and user space sends empty set of strings, the ffs->stringtabs field remains NULL. Thus *ffs->stringtabs in functionfs_bind leads to a NULL pointer dereferenece. The bug was introduced by commit [fd7c9a007f: “use usb_string_ids_n()”]. While at it, remove double initialisation of lang local variable in that function. ffs->strings_count does not need to be checked in any way since in the above scenario it will remain zero and usb_string_ids_n() is a no-operation when colled with 0 argument. Signed-off-by: Michal Nazarewicz <mina86@mina86.com> Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-07-09USB: ftdi_sio: fix null deref at port probeJohan Hovold
commit aea1ae8760314e072bf1b773521e9de5d5dda10d upstream. Fix NULL-pointer dereference when probing an interface with no endpoints. These devices have two bulk endpoints per interface, but this avoids crashing the kernel if a user forces a non-FTDI device to be probed. Note that the iterator variable was made unsigned in order to avoid a maybe-uninitialized compiler warning for ep_desc after the loop. Fixes: 895f28badce9 ("USB: ftdi_sio: fix hi-speed device packet size calculation") Reported-by: Mike Remski <mremski@mutualink.net> Tested-by: Mike Remski <mremski@mutualink.net> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-07-09usb: option: add/modify Olivetti Olicard modemsBjørn Mork
commit b0ebef36e93703e59003ad6a1a20227e47714417 upstream. Adding a couple of Olivetti modems and blacklisting the net function on a couple which are already supported. Reported-by: Lars Melin <larsm17@gmail.com> Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-07-09USB: option: add device ID for SpeedUp SU9800 usb 3g modemOliver Neukum
commit 1cab4c68e339086cdaff7535848e878e8f261fca upstream. Reported by Alif Mubarak Ahmad: This device vendor and product id is 1c9e:9800 It is working as serial interface with generic usbserial driver. I thought it is more suitable to use usbserial option driver, which has better capability distinguishing between modem serial interface and micro sd storage interface. [ johan: style changes ] Signed-off-by: Oliver Neukum <oneukum@suse.de> Tested-by: Alif Mubarak Ahmad <alive4ever@live.com> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-07-09xhci: Fix runtime suspended xhci from blocking system suspend.Wang, Yu
commit d6236f6d1d885aa19d1cd7317346fe795227a3cc upstream. The system suspend flow as following: 1, Freeze all user processes and kenrel threads. 2, Try to suspend all devices. 2.1, If pci device is in RPM suspended state, then pci driver will try to resume it to RPM active state in the prepare stage. 2.2, xhci_resume function calls usb_hcd_resume_root_hub to queue two workqueue items to resume usb2&usb3 roothub devices. 2.3, Call suspend callbacks of devices. 2.3.1, All suspend callbacks of all hcd's children, including roothub devices are called. 2.3.2, Finally, hcd_pci_suspend callback is called. Due to workqueue threads were already frozen in step 1, the workqueue items can't be scheduled, and the roothub devices can't be resumed in this flow. The HCD_FLAG_WAKEUP_PENDING flag which is set in usb_hcd_resume_root_hub won't be cleared. Finally, hcd_pci_suspend will return -EBUSY, and system suspend fails. The reason why this issue doesn't show up very often is due to that choose_wakeup will be called in step 2.3.1. In step 2.3.1, if udev->do_remote_wakeup is not equal to device_may_wakeup(&udev->dev), then udev will resume to RPM active for changing the wakeup settings. This has been a lucky hit which hides this issue. For some special xHCI controllers which have no USB2 port, then roothub will not match hub driver due to probe failed. Then its do_remote_wakeup will be set to zero, and we won't be as lucky. xhci driver doesn't need to resume roothub devices everytime like in the above case. It's only needed when there are pending event TRBs. This patch should be back-ported to kernels as old as 3.2, that contains the commit f69e3120df82391a0ee8118e0a156239a06b2afb "USB: XHCI: resume root hubs when the controller resumes" Signed-off-by: Wang, Yu <yu.y.wang@intel.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> [use readl() instead of removed xhci_readl(), reword commit message -Mathias] Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-07-09xhci: correct burst count field for isoc transfers on 1.0 xhci hostsMathias Nyman
commit 3213b151387df0b95f4eada104f68eb1c1409cb3 upstream. The transfer burst count (TBC) field in xhci 1.0 hosts should be set to the number of bursts needed to transfer all packets in a isoc TD. Supported values are 0-2 (1 to 3 bursts per service interval). Formula for TBC calculation is given in xhci spec section 4.11.2.3: TBC = roundup( Transfer Descriptor Packet Count / Max Burst Size +1 ) - 1 This patch should be applied to stable kernels since 3.0 that contain the commit 5cd43e33b9519143f06f507dd7cbee6b7a621885 "xhci 1.0: Set transfer burst count field." Suggested-by: ShiChun Ma <masc2008@qq.com> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-07-09ibmvscsi: Abort init sequence during error recoveryBrian King
commit 9ee755974bea2f9880e517ec985dc9dede1b3a36 upstream. If a CRQ reset is triggered for some reason while in the middle of performing VSCSI adapter initialization, we don't want to call the done function for the initialization MAD commands as this will only result in two threads attempting initialization at the same time, resulting in failures. Signed-off-by: Brian King <brking@linux.vnet.ibm.com> Acked-by: Nathan Fontenot <nfont@linux.vnet.ibm.com> Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-07-06IB/umad: Fix use-after-free on closeBart Van Assche
commit 60e1751cb52cc6d1ae04b6bd3c2b96e770b5823f upstream. Avoid that closing /dev/infiniband/umad<n> or /dev/infiniband/issm<n> triggers a use-after-free. __fput() invokes f_op->release() before it invokes cdev_put(). Make sure that the ib_umad_device structure is freed by the cdev_put() call instead of f_op->release(). This avoids that changing the port mode from IB into Ethernet and back to IB followed by restarting opensmd triggers the following kernel oops: general protection fault: 0000 [#1] PREEMPT SMP RIP: 0010:[<ffffffff810cc65c>] [<ffffffff810cc65c>] module_put+0x2c/0x170 Call Trace: [<ffffffff81190f20>] cdev_put+0x20/0x30 [<ffffffff8118e2ce>] __fput+0x1ae/0x1f0 [<ffffffff8118e35e>] ____fput+0xe/0x10 [<ffffffff810723bc>] task_work_run+0xac/0xe0 [<ffffffff81002a9f>] do_notify_resume+0x9f/0xc0 [<ffffffff814b8398>] int_signal+0x12/0x17 Reference: https://bugzilla.kernel.org/show_bug.cgi?id=75051 Signed-off-by: Bart Van Assche <bvanassche@acm.org> Reviewed-by: Yann Droneaud <ydroneaud@opteya.com> Signed-off-by: Roland Dreier <roland@purestorage.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-07-06IB/umad: Fix error handlingBart Van Assche
commit 8ec0a0e6b58218bdc1db91dd70ebfcd6ad8dd6cd upstream. Avoid leaking a kref count in ib_umad_open() if port->ib_dev == NULL or if nonseekable_open() fails. Avoid leaking a kref count, that sm_sem is kept down and also that the IB_PORT_SM capability mask is not cleared in ib_umad_sm_open() if nonseekable_open() fails. Since container_of() never returns NULL, remove the code that tests whether container_of() returns NULL. Moving the kref_get() call from the start of ib_umad_*open() to the end is safe since it is the responsibility of the caller of these functions to ensure that the cdev pointer remains valid until at least when these functions return. Signed-off-by: Bart Van Assche <bvanassche@acm.org> [ydroneaud@opteya.com: rework a bit to reduce the amount of code changed] Signed-off-by: Yann Droneaud <ydroneaud@opteya.com> [ nonseekable_open() can't actually fail, but.... - Roland ] Signed-off-by: Roland Dreier <roland@purestorage.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>