| Age | Commit message (Collapse) | Author |
|---|
|
commit 8a0435d958fb36d93b8df610124a0e91e5675c82 upstream.
This extends Benjamin Tissoires manual min/max quirk table with support for
the ThinkPad X240.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 421e08c41fda1f0c2ff6af81a67b491389b653a5 upstream.
The new Lenovo Haswell series (-40's) contains a new Synaptics touchpad.
However, these new Synaptics devices report bad axis ranges.
Under Windows, it is not a problem because the Windows driver uses RMI4
over SMBus to talk to the device. Under Linux, we are using the PS/2
fallback interface and it occurs the reported ranges are wrong.
Of course, it would be too easy to have only one range for the whole
series, each touchpad seems to be calibrated in a different way.
We can not use SMBus to get the actual range because I suspect the firmware
will switch into the SMBus mode and stop talking through PS/2 (this is the
case for hybrid HID over I2C / PS/2 Synaptics touchpads).
So as a temporary solution (until RMI4 land into upstream), start a new
list of quirks with the min/max manually set.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ca2beaf84d9678c12b17d92623f0e90829d6ca13 upstream.
This prefixes all externally-visible symbols of speakup with "spk_".
Signed-off-by: Samuel Thibault <samuel.thibault@ens-lyon.org>
Cc: Kamal Mostafa <kamal@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 1aa9578c1a9450fb21501c4f549f5b1edb557e6d upstream.
Don Zickus <dzickus@redhat.com> writes:
Some co-workers of mine bought Samsung laptops that had mostly usb3 ports.
Those ports did not resume correctly (the driver would timeout communicating
and fail). This led to frustration as suspend/resume is a common use for
laptops.
Poking around, I applied the reset on resume quirk to this chipset and the
resume started working. Reloading the xhci_hcd module had been the temporary
workaround.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Reported-by: Don Zickus <dzickus@redhat.com>
Tested-by: Prarit Bhargava <prarit@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit c15bdfd5b9831e4cab8cfc118243956e267dd30e upstream.
The current assumption in the elantech driver that hw version 3 touchpads
are never clickpads and hw version 4 touchpads are always clickpads is
wrong.
There are several bug reports for this, ie:
https://bugzilla.redhat.com/show_bug.cgi?id=1030802
http://superuser.com/questions/619582/right-elantech-touchpad-button-not-working-in-linux
I've spend a couple of hours wading through various bugzillas, launchpads
and forum posts to create a list of fw-versions and capabilities for
different laptop models to find a good method to differentiate between
clickpads and versions with separate hardware buttons.
Which shows that a device being a clickpad is reliable indicated by bit 12
being set in the fw_version. I've included the gathered list inside the
driver, so that we've this info at hand if we need to revisit this later.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Josh Boyer <jwboyer@fedoraproject.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 75135da0d68419ef8a925f4c1d5f63d8046e314d upstream.
pci_get_device() decrements the reference count of "from" (last
argument) so when we break off the loop successfully we have only one
device reference - and we don't know which device we have. If we want
a reference to each device, we must take them explicitly and let
the pci_get_device() walk complete to avoid duplicate references.
This is serious, as over-putting device references will cause
the device to eventually disappear. Without this fix, the kernel
crashes after a few insmod/rmmod cycles.
Tested on an Intel S7000FC4UR system with a 7300 chipset.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Link: http://lkml.kernel.org/r/20140224111656.09bbb7ed@endymion.delvare
Cc: Mauro Carvalho Chehab <m.chehab@samsung.com>
Cc: Doug Thompson <dougthompson@xmission.com>
Cc: stable@vger.kernel.org
Signed-off-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 608cfbe4abaf76e9d732efd7ed1cfa3998163d91 upstream.
The call to clamp_t() first truncates the variable signed 8 bit and as a
result, the actual clamp is a no-op.
Fixes: 0d78156eef1d ('p54: improve site survey')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Linux 3.4.83 included an incomplete backport of commit
8a964f44e01ad3bbc208c3e80d931ba91b9ea786 ('iwlwifi: always copy first
16 bytes of commands') which causes a regression for this driver.
This is the missing piece.
Reported-by: Andreas Sturmlechner <andreas.sturmlechner@gmail.com>
Cc: Johannes Berg <johannes.berg@intel.com>
Cc: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Cc: Jianguo Wu <wujianguo@huawei.com>
Cc: Andres Bertens <abertensu@yahoo.com>
Tested-by: Andreas Sturmlechner <andreas.sturmlechner@gmail.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit b12bb60d6c350b348a4e1460cd68f97ccae9822e upstream.
If the initialization of storvsc fails, the storvsc_device_destroy()
causes NULL pointer dereference.
storvsc_bus_scan()
scsi_scan_target()
__scsi_scan_target()
scsi_probe_and_add_lun(hostdata=NULL)
scsi_alloc_sdev(hostdata=NULL)
sdev->hostdata = hostdata
now the host allocation fails
__scsi_remove_device(sdev)
calls sdev->host->hostt->slave_destroy() ==
storvsc_device_destroy(sdev)
access of sdev->hostdata->request_mempool
Signed-off-by: Ales Novak <alnovak@suse.cz>
Signed-off-by: Thomas Abraham <tabraham@suse.com>
Reviewed-by: Jiri Kosina <jkosina@suse.cz>
Acked-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b77ed25c9f8402e8b3e49e220edb4ef09ecfbb53 upstream.
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit c59053a23d586675c25d789a7494adfdc02fba57 upstream.
In the first place, the loop 'for' in the macro 'for_each_isci_host'
(drivers/scsi/isci/host.h:314) is incorrect, because it accesses
the 3rd element of 2 element array. After the 2nd iteration it executes
the instruction:
ihost = to_pci_info(pdev)->hosts[2]
(while the size of the 'hosts' array equals 2) and reads an
out of range element.
In the second place, this loop is incorrectly optimized by GCC v4.8
(see http://marc.info/?l=linux-kernel&m=138998871911336&w=2).
As a result, on platforms with two SCU controllers,
the loop is executed more times than it can be (for i=0,1 and 2).
It causes kernel panic during entering the S3 state
and the following oops after 'rmmod isci':
BUG: unable to handle kernel NULL pointer dereference at (null)
IP: [<ffffffff8131360b>] __list_add+0x1b/0xc0
Oops: 0000 [#1] SMP
RIP: 0010:[<ffffffff8131360b>] [<ffffffff8131360b>] __list_add+0x1b/0xc0
Call Trace:
[<ffffffff81661b84>] __mutex_lock_slowpath+0x114/0x1b0
[<ffffffff81661c3f>] mutex_lock+0x1f/0x30
[<ffffffffa03e97cb>] sas_disable_events+0x1b/0x50 [libsas]
[<ffffffffa03e9818>] sas_unregister_ha+0x18/0x60 [libsas]
[<ffffffffa040316e>] isci_unregister+0x1e/0x40 [isci]
[<ffffffffa0403efd>] isci_pci_remove+0x5d/0x100 [isci]
[<ffffffff813391cb>] pci_device_remove+0x3b/0xb0
[<ffffffff813fbf7f>] __device_release_driver+0x7f/0xf0
[<ffffffff813fc8f8>] driver_detach+0xa8/0xb0
[<ffffffff813fbb8b>] bus_remove_driver+0x9b/0x120
[<ffffffff813fcf2c>] driver_unregister+0x2c/0x50
[<ffffffff813381f3>] pci_unregister_driver+0x23/0x80
[<ffffffffa04152f8>] isci_exit+0x10/0x1e [isci]
[<ffffffff810d199b>] SyS_delete_module+0x16b/0x2d0
[<ffffffff81012a21>] ? do_notify_resume+0x61/0xa0
[<ffffffff8166ce29>] system_call_fastpath+0x16/0x1b
The loop has been corrected.
This patch fixes kernel panic during entering the S3 state
and the above oops.
Signed-off-by: Lukasz Dorau <lukasz.dorau@intel.com>
Reviewed-by: Maciej Patelczyk <maciej.patelczyk@intel.com>
Tested-by: Lukasz Dorau <lukasz.dorau@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ddfadd7736b677de2d4ca2cd5b4b655368c85a7a upstream.
Remove an erroneous BUG_ON() in the case of a hard reset timeout. The
reset timeout handler puts the port into the "awaiting link-up" state.
The timeout causes the device to be disconnected and we need to be in
the awaiting link-up state to re-connect the port. The BUG_ON() made
the incorrect assumption that resets never timeout and we always
complete the reset in the "resetting" state.
Testing this patch also uncovered that libata continues to attempt to
reset the port long after the driver has torn down the context. Once
the driver has committed to abandoning the link it must indicate to
libata that recovery ends by returning -ENODEV from
->lldd_I_T_nexus_reset().
Acked-by: Lukasz Dorau <lukasz.dorau@intel.com>
Reported-by: David Milburn <dmilburn@redhat.com>
Reported-by: Xun Ni <xun.ni@intel.com>
Tested-by: Xun Ni <xun.ni@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 7e9e148af01ef388efb6e2490805970be4622792 upstream.
If flexcan_chip_start() in flexcan_open() fails, the interrupt is not freed,
this patch adds the missing cleanup.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 0a8d8c446b5429d15ff2d48f46e00d8a08552303 upstream.
Since commit d25f06ea466e "vmxnet3: fix netpoll race condition",
the vmxnet3 driver fails to build when CONFIG_PCI_MSI is disabled,
because it unconditionally references the vmxnet3_msix_rx()
function.
To fix this, use the same #ifdef in the caller that exists around
the function definition.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Neil Horman <nhorman@tuxdriver.com>
Cc: Shreyas Bhatewara <sbhatewara@vmware.com>
Cc: "VMware, Inc." <pv-drivers@vmware.com>
Cc: "David S. Miller" <davem@davemloft.net>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d25f06ea466ea521b563b76661180b4e44714ae6 upstream.
vmxnet3's netpoll driver is incorrectly coded. It directly calls
vmxnet3_do_poll, which is the driver internal napi poll routine. As the netpoll
controller method doesn't block real napi polls in any way, there is a potential
for race conditions in which the netpoll controller method and the napi poll
method run concurrently. The result is data corruption causing panics such as this
one recently observed:
PID: 1371 TASK: ffff88023762caa0 CPU: 1 COMMAND: "rs:main Q:Reg"
#0 [ffff88023abd5780] machine_kexec at ffffffff81038f3b
#1 [ffff88023abd57e0] crash_kexec at ffffffff810c5d92
#2 [ffff88023abd58b0] oops_end at ffffffff8152b570
#3 [ffff88023abd58e0] die at ffffffff81010e0b
#4 [ffff88023abd5910] do_trap at ffffffff8152add4
#5 [ffff88023abd5970] do_invalid_op at ffffffff8100cf95
#6 [ffff88023abd5a10] invalid_op at ffffffff8100bf9b
[exception RIP: vmxnet3_rq_rx_complete+1968]
RIP: ffffffffa00f1e80 RSP: ffff88023abd5ac8 RFLAGS: 00010086
RAX: 0000000000000000 RBX: ffff88023b5dcee0 RCX: 00000000000000c0
RDX: 0000000000000000 RSI: 00000000000005f2 RDI: ffff88023b5dcee0
RBP: ffff88023abd5b48 R8: 0000000000000000 R9: ffff88023a3b6048
R10: 0000000000000000 R11: 0000000000000002 R12: ffff8802398d4cd8
R13: ffff88023af35140 R14: ffff88023b60c890 R15: 0000000000000000
ORIG_RAX: ffffffffffffffff CS: 0010 SS: 0018
#7 [ffff88023abd5b50] vmxnet3_do_poll at ffffffffa00f204a [vmxnet3]
#8 [ffff88023abd5b80] vmxnet3_netpoll at ffffffffa00f209c [vmxnet3]
#9 [ffff88023abd5ba0] netpoll_poll_dev at ffffffff81472bb7
The fix is to do as other drivers do, and have the poll controller call the top
half interrupt handler, which schedules a napi poll properly to recieve frames
Tested by myself, successfully.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
CC: Shreyas Bhatewara <sbhatewara@vmware.com>
CC: "VMware, Inc." <pv-drivers@vmware.com>
CC: "David S. Miller" <davem@davemloft.net>
Reviewed-by: Shreyas N Bhatewara <sbhatewara@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d03874c881a049a50e12f285077ab1f9fc2686e1 upstream.
We need to check for DVI vs. HDMI when setting up duallink since
HDMI is single link only. Fixes 4k modes on newer asics.
bug:
https://bugs.freedesktop.org/show_bug.cgi?id=75223
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
M8 (2BA30001)
commit b28a613e9138e4b3a64649bd60b13436f4b4b49b upstream.
Via commit 87809942d3fa "libata: add ATA_HORKAGE_BROKEN_FPDMA_AA quirk
for Seagate Momentus SpinPoint M8" we added a quirk for disks named
"ST1000LM024 HN-M101MBB" with firmware revision "2AR10001".
As reported on https://bugzilla.redhat.com/show_bug.cgi?id=1073901,
we need to also add firmware revision 2BA30001 as it is broken as well.
Reported-by: Nicholas <arealityfarbetween@googlemail.com>
Signed-off-by: Michele Baldessari <michele@acksyn.org>
Tested-by: Guilherme Amadio <guilherme.amadio@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 70044d71d31d6973665ced5be04ef39ac1c09a48 upstream.
PREPARE_[DELAYED_]WORK() are being phased out. They have few users
and a nasty surprise in terms of reentrancy guarantee as workqueue
considers work items to be different if they don't have the same work
function.
firewire core-device and sbp2 have been been multiplexing work items
with multiple work functions. Introduce fw_device_workfn() and
sbp2_lu_workfn() which invoke fw_device->workfn and
sbp2_logical_unit->workfn respectively and always use the two
functions as the work functions and update the users to set the
->workfn fields instead of overriding work functions using
PREPARE_DELAYED_WORK().
This fixes a variety of possible regressions since a2c1c57be8d9
"workqueue: consider work function when searching for busy work items"
due to which fw_workqueue lost its required non-reentrancy property.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Cc: linux1394-devel@lists.sourceforge.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 8987583366ae9e03c306c2b7d73bdb952df1d08d upstream.
Commit 8408dc1c14c1 "firewire: net: use dev_printk API" introduced a
use-after-free in a failure path. fwnet_transmit_packet_failed(ptask)
may free ptask, then the dev_err() call dereferenced it. The fix is
straightforward; simply reorder the two calls.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 9ef7506f7eff3fc42724269f62e30164c141661f upstream.
A few of the simpler TTM drivers (cirrus, ast, mgag200) do not implement
this function. Yet can end up somehow with an evicted bo:
BUG: unable to handle kernel NULL pointer dereference at (null)
IP: [< (null)>] (null)
PGD 16e761067 PUD 16e6cf067 PMD 0
Oops: 0010 [#1] SMP
Modules linked in: bnep bluetooth rfkill fuse ip6t_rpfilter ip6t_REJECT ipt_REJECT xt_conntrack ebtable_nat ebtable_broute bridge stp llc ebtable_filter ebtables ip6table_nat nf_conntrack_ipv6 nf_defrag_ipv6 nf_nat_ipv6 ip6table_mangle ip6table_security ip6table_raw ip6table_filter ip6_tables iptable_nat nf_conntrack_ipv4 nf_defrag_ipv4 nf_nat_ipv4 nf_nat nf_conntrack iptable_mangle iptable_security iptable_raw iptable_filter ip_tables sg btrfs zlib_deflate raid6_pq xor dm_queue_length iTCO_wdt iTCO_vendor_support coretemp kvm dcdbas dm_service_time microcode serio_raw pcspkr lpc_ich mfd_core i7core_edac edac_core ses enclosure ipmi_si ipmi_msghandler shpchp acpi_power_meter mperf nfsd auth_rpcgss nfs_acl lockd uinput sunrpc dm_multipath xfs libcrc32c ata_generic pata_acpi sr_mod cdrom
sd_mod usb_storage mgag200 syscopyarea sysfillrect sysimgblt i2c_algo_bit lpfc drm_kms_helper ttm crc32c_intel ata_piix bfa drm ixgbe libata i2c_core mdio crc_t10dif ptp crct10dif_common pps_core scsi_transport_fc dca scsi_tgt megaraid_sas bnx2 dm_mirror dm_region_hash dm_log dm_mod
CPU: 16 PID: 2572 Comm: X Not tainted 3.10.0-86.el7.x86_64 #1
Hardware name: Dell Inc. PowerEdge R810/0H235N, BIOS 0.3.0 11/14/2009
task: ffff8801799dabc0 ti: ffff88016c884000 task.ti: ffff88016c884000
RIP: 0010:[<0000000000000000>] [< (null)>] (null)
RSP: 0018:ffff88016c885ad8 EFLAGS: 00010202
RAX: ffffffffa04e94c0 RBX: ffff880178937a20 RCX: 0000000000000000
RDX: 0000000000000000 RSI: 0000000000240004 RDI: ffff880178937a00
RBP: ffff88016c885b60 R08: 00000000000171a0 R09: ffff88007cf171a0
R10: ffffea0005842540 R11: ffffffff810487b9 R12: ffff880178937b30
R13: ffff880178937a00 R14: ffff88016c885b78 R15: ffff880179929400
FS: 00007f81ba2ef980(0000) GS:ffff88007cf00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000000000000 CR3: 000000016e763000 CR4: 00000000000007e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
Stack:
ffffffffa0306fae ffff8801799295c0 0000000000260004 0000000000000001
ffff88016c885b60 ffffffffa0307669 00ff88007cf17738 ffff88017cf17700
ffff880178937a00 ffff880100000000 ffff880100000000 0000000079929400
Call Trace:
[<ffffffffa0306fae>] ? ttm_bo_handle_move_mem+0x54e/0x5b0 [ttm]
[<ffffffffa0307669>] ? ttm_bo_mem_space+0x169/0x340 [ttm]
[<ffffffffa0307bd7>] ttm_bo_move_buffer+0x117/0x130 [ttm]
[<ffffffff81130001>] ? perf_event_init_context+0x141/0x220
[<ffffffffa0307cb1>] ttm_bo_validate+0xc1/0x130 [ttm]
[<ffffffffa04e7377>] mgag200_bo_pin+0x87/0xc0 [mgag200]
[<ffffffffa04e56c4>] mga_crtc_cursor_set+0x474/0xbb0 [mgag200]
[<ffffffff811971d2>] ? __mem_cgroup_commit_charge+0x152/0x3b0
[<ffffffff815c4182>] ? mutex_lock+0x12/0x2f
[<ffffffffa0201433>] drm_mode_cursor_common+0x123/0x170 [drm]
[<ffffffffa0205231>] drm_mode_cursor_ioctl+0x41/0x50 [drm]
[<ffffffffa01f5ca2>] drm_ioctl+0x502/0x630 [drm]
[<ffffffff815cbab4>] ? __do_page_fault+0x1f4/0x510
[<ffffffff8101cb68>] ? __restore_xstate_sig+0x218/0x4f0
[<ffffffff811b4445>] do_vfs_ioctl+0x2e5/0x4d0
[<ffffffff8124488e>] ? file_has_perm+0x8e/0xa0
[<ffffffff811b46b1>] SyS_ioctl+0x81/0xa0
[<ffffffff815d05d9>] system_call_fastpath+0x16/0x1b
Code: Bad RIP value.
RIP [< (null)>] (null)
RSP <ffff88016c885ad8>
CR2: 0000000000000000
Signed-off-by: Rob Clark <rclark@redhat.com>
Reviewed-by: Jérôme Glisse <jglisse@redhat.com>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit c99b1861c232e1f641f13b8645e0febb3712cc71 upstream.
While preparing association request, intersection of device's HT
capability information and corresponding fields advertised by AP
is used.
This patch fixes an error while copying this field from AP's
beacon.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b3050248c167871ca52cfdb2ce78aa2460249346 upstream.
The minimum CCA power threshold values have to be adjusted
for existing cards to be in compliance with new regulations.
Newer cards will make use of the values obtained from EEPROM,
support for this was added earlier. To make sure that cards
that are already in use and don't have proper values in EEPROM,
do not violate regulations, use the initvals instead.
Reported-by: Jeang Daniel <dyjeong@qca.qualcomm.com>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit d7b95315cc7f441418845a165ee56df723941487 ]
Redefine the RXD_ERR_MASK to include only relevant error bits. This fixes
a customer reported issue of randomly dropping packets on the 5719.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 0e7ede80d929ff0f830c44a543daa1acd590c749 ]
We should alloc big buffers also when guest can receive UFO
packets to let the big packets fit into guest rx buffer.
Fixes 5c5167515d80f78f6bb538492c423adcae31ad65
(virtio-net: Allow UFO feature to be set and advertised.)
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Sridhar Samudrala <sri@us.ibm.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d43ff4cd798911736fb39025ec8004284b1b0bc2 upstream.
The struct driver_info ax88178_info is assigned the function
asix_rx_fixup_common as it's rx_fixup callback. This means that
FLAG_MULTI_PACKET must be set as this function is cloning the
data and calling usbnet_skb_return. Not setting this flag leads
to usbnet_skb_return beeing called a second time from within
the rx_process function in the usbnet module.
Signed-off-by: Emil Goode <emilgoode@gmail.com>
Reported-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 8b5b6f5413e97c3e8bafcdd67553d508f4f698cd upstream.
ASIX AX88772B started to pack data even more tightly. Packets and the ASIX packet
header may now cross URB boundaries. To handle this we have to introduce
some state between individual calls to asix_rx_fixup().
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
[ Emil: backported to 3.4: dropped changes to drivers/net/usb/ax88172a.c ]
Signed-off-by: Emil Goode <emilgoode@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 0c5d63f0ab6728f05ddefa25aff55e31297f95e6 upstream.
All of the rtlwifi drivers have an error in the routine that tests if
the data is "special". If it is, the subsequant transmission will be
at the lowest rate to enhance reliability. The 16-bit quantity is
big-endian, but was being extracted in native CPU mode. One of the
effects of this bug is to inhibit association under some conditions
as the TX rate is too high.
Based on suggestions by Joe Perches, the entire routine is rewritten.
One of the local headers contained duplicates of some of the ETH_P_XXX
definitions. These are deleted.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
[wujg: Backported to 3.4:
- adjust context
- remove rtlpriv->enter_ps = false
- use schedule_work(&rtlpriv->works.lps_leave_work)]
Signed-off-by: Jianguo Wu <wujianguo@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 08a5dd3842f2ac61c6d69661d2d96022df8ae359 upstream.
Add some new PCI IDs to the table for 6000, 6005 and 6235 series.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
[bwh: Backported to 3.2:
- Adjust filenames
- Drop const from struct iwl_cfg]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
[wujg: Backported to 3.4:
- Adjust context
- Do not drop const from struct iwl_cfg]
Signed-off-by: Jianguo Wu <wujianguo@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 9186a1fd9ed190739423db84bc344d258ef3e3d7 upstream.
If channel switch is pending and we remove interface we can
crash like showed below due to passing NULL vif to mac80211:
BUG: unable to handle kernel paging request at fffffffffffff8cc
IP: [<ffffffff8130924d>] strnlen+0xd/0x40
Call Trace:
[<ffffffff8130ad2e>] string.isra.3+0x3e/0xd0
[<ffffffff8130bf99>] vsnprintf+0x219/0x640
[<ffffffff8130c481>] vscnprintf+0x11/0x30
[<ffffffff81061585>] vprintk_emit+0x115/0x4f0
[<ffffffff81657bd5>] printk+0x61/0x63
[<ffffffffa048987f>] ieee80211_chswitch_done+0xaf/0xd0 [mac80211]
[<ffffffffa04e7b34>] iwl_chswitch_done+0x34/0x40 [iwldvm]
[<ffffffffa04f83c3>] iwlagn_commit_rxon+0x2a3/0xdc0 [iwldvm]
[<ffffffffa04ebc50>] ? iwlagn_set_rxon_chain+0x180/0x2c0 [iwldvm]
[<ffffffffa04e5e76>] iwl_set_mode+0x36/0x40 [iwldvm]
[<ffffffffa04e5f0d>] iwlagn_mac_remove_interface+0x8d/0x1b0 [iwldvm]
[<ffffffffa0459b3d>] ieee80211_do_stop+0x29d/0x7f0 [mac80211]
This is because we nulify ctx->vif in iwlagn_mac_remove_interface()
before calling some other functions that teardown interface. To fix
just check ctx->vif on iwl_chswitch_done(). We should not call
ieee80211_chswitch_done() as channel switch works were already canceled
by mac80211 in ieee80211_do_stop() -> ieee80211_mgd_stop().
Resolve:
https://bugzilla.redhat.com/show_bug.cgi?id=979581
Reported-by: Lukasz Jagiello <jagiello.lukasz@gmail.com>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
[bwh: Backported to 3.2: adjust context, filename]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
[wujg: Backported to 3.4: - adjust context]
Signed-off-by: Jianguo Wu <wujianguo@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 707aee401d2467baa785a697f40a6e2d9ee79ad5 upstream.
The BT_CONFIG command that is sent to the device during
startup will enable BT coex unless the module parameter
turns it off, but on devices without Bluetooth this may
cause problems, as reported in Redhat BZ 885407.
Fix this by sending the BT_CONFIG command only when the
device has Bluetooth.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
[bwh: Backported to 3.2:
- Adjust filename
- s/priv->lib/priv->cfg/]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
[wujg: Backported to 3.4:
- s/priv->cfg/priv->shrd->cfg/]
Signed-off-by: Jianguo Wu <wujianguo@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 8a964f44e01ad3bbc208c3e80d931ba91b9ea786 upstream.
The FH hardware will always write back to the scratch field
in commands, even host commands not just TX commands, which
can overwrite parts of the command. This is problematic if
the command is re-used (with IWL_HCMD_DFL_NOCOPY) and can
cause calibration issues.
Address this problem by always putting at least the first
16 bytes into the buffer we also use for the command header
and therefore make the DMA engine write back into this.
For commands that are smaller than 16 bytes also always map
enough memory for the DMA engine to write back to.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
[bwh: Backported to 3.2:
- Adjust context
- Drop the IWL_HCMD_DFL_DUP handling
- Fix descriptor addresses and lengths for tracepoint, but otherwise
leave it unchanged]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
[wujg: Backported to 3.4: adjust context]
Signed-off-by: Jianguo Wu <wujianguo@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 7c34158231b2eda8dcbd297be2bb1559e69cb433 upstream.
The RX replenish code doesn't handle DMA mapping failures,
which will cause issues if there actually is a failure. This
was reported by Shuah Khan who found a DMA mapping framework
warning ("device driver failed to check map error").
Reported-by: Shuah Khan <shuah.khan@hp.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
[bwh: Backported to 3.2:
- Adjust filename, context, indentation
- Use bus(trans) instead of trans where necessary
- Use hw_params(trans).rx_page_order instead of trans_pcie->rx_page_order]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
[wujg: Backported to 3.4:
- Adjust context
- Use trans instead of bus(trans)
- Use hw_params(trans).rx_page_order instead of trans_pcie->rx_page_order]
Signed-off-by: Jianguo Wu <wujianguo@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 25a172655f837bdb032e451f95441bb4acec51bb upstream.
This can lead to a panic if the driver isn't ready to
handle them. Since our interrupt line is shared, we can get
an interrupt at any time (and CONFIG_DEBUG_SHIRQ checks
that even when the interrupt is being freed).
If the op_mode has gone away, we musn't call it. To avoid
this the transport disables the interrupts when the hw is
stopped and the op_mode is leaving.
If there is an event that would cause an interrupt the INTA
register is updated regardless of the enablement of the
interrupts: even if the interrupts are disabled, the INTA
will be changed, but the device won't issue an interrupt.
But the ISR can be called at any time, so we ought ignore
the value in the INTA otherwise we can call the op_mode
after it was freed.
I found this bug when the op_mode_start failed, and called
iwl_trans_stop_hw(trans, true). Then I played with the
RFKILL button, and removed the module.
While removing the module, the IRQ is freed, and the ISR is
called (CONFIG_DEBUG_SHIRQ enabled). Panic.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
[bwh: Backported to 3.2:
- Adjust context
- Pass bus(trans), not trans, to iwl_{read,write}32()]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
[wujg: Backported to 3.4:
- adjust context
- Pass trans to iwl_{read,write}32()}]
Signed-off-by: Jianguo Wu <wujianguo@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 4fc79db178f0a0ede479b4713e00df2d106028b3 upstream.
If the device is not started, we can't read its
SRAM and attempting to do so will cause issues.
Protect the debugfs read.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
[wujg: Backported to 3.4: adjust context]
Signed-off-by: Jianguo Wu <wujianguo@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 94543a8d4fb302817014981489f15cb3b92ec3c2 upstream.
iwl_dbgfs_fh_reg_read() can cause crashes and/or
BUG_ON in slub because the ifdefs are wrong, the
code in iwl_dump_fh() should use DEBUGFS, not
DEBUG to protect the buffer writing code.
Also, while at it, clean up the arguments to the
function, some code and make it generally safer.
Reported-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
[bwh: Backported to 3.2: adjust filenames and context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
[wujg: Backported to 3.4: adjust context]
Signed-off-by: Jianguo Wu <wujianguo@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 86f0b5b86d142b9323432fef078a6cf0fb5dda74 upstream.
snd_pcm_stop() must be called in the PCM substream lock context.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Cc: Weng Meiling <wengmeiling.weng@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 5e72fdb8d827560893642e85a251d339109a00f4 upstream.
commit 4704fe4f03a5ab27e3c36184af85d5000e0f8a48 upstream.
When a event is being bound to a VCPU there is a window between the
EVTCHNOP_bind_vpcu call and the adjustment of the local per-cpu masks
where an event may be lost. The hypervisor upcalls the new VCPU but
the kernel thinks that event is still bound to the old VCPU and
ignores it.
There is even a problem when the event is being bound to the same VCPU
as there is a small window beween the clear_bit() and set_bit() calls
in bind_evtchn_to_cpu(). When scanning for pending events, the kernel
may read the bit when it is momentarily clear and ignore the event.
Avoid this by masking the event during the whole bind operation.
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Reviewed-by: Jan Beulich <jbeulich@suse.com>
[bwh: Backported to 3.2: remove the BM() cast]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Cc: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 9371cadbbcc7c00c81753b9727b19fb3bc74d458 upstream.
commit 8e3f8755545cc4a7f4da8e9ef76d6d32e0dca576 upstream.
Check that the ring does not have an insane amount of requests
(more than there could fit on the ring).
If we detect this case we will stop processing the requests
and wait until the XenBus disconnects the ring.
The existing check RING_REQUEST_CONS_OVERFLOW which checks for how
many responses we have created in the past (rsp_prod_pvt) vs
requests consumed (req_cons) and whether said difference is greater or
equal to the size of the ring, does not catch this case.
Wha the condition does check if there is a need to process more
as we still have a backlog of responses to finish. Note that both
of those values (rsp_prod_pvt and req_cons) are not exposed on the
shared ring.
To understand this problem a mini crash course in ring protocol
response/request updates is in place.
There are four entries: req_prod and rsp_prod; req_event and rsp_event
to track the ring entries. We are only concerned about the first two -
which set the tone of this bug.
The req_prod is a value incremented by frontend for each request put
on the ring. Conversely the rsp_prod is a value incremented by the backend
for each response put on the ring (rsp_prod gets set by rsp_prod_pvt when
pushing the responses on the ring). Both values can
wrap and are modulo the size of the ring (in block case that is 32).
Please see RING_GET_REQUEST and RING_GET_RESPONSE for the more details.
The culprit here is that if the difference between the
req_prod and req_cons is greater than the ring size we have a problem.
Fortunately for us, the '__do_block_io_op' loop:
rc = blk_rings->common.req_cons;
rp = blk_rings->common.sring->req_prod;
while (rc != rp) {
..
blk_rings->common.req_cons = ++rc; /* before make_response() */
}
will loop up to the point when rc == rp. The macros inside of the
loop (RING_GET_REQUEST) is smart and is indexing based on the modulo
of the ring size. If the frontend has provided a bogus req_prod value
we will loop until the 'rc == rp' - which means we could be processing
already processed requests (or responses) often.
The reason the RING_REQUEST_CONS_OVERFLOW is not helping here is
b/c it only tracks how many responses we have internally produced
and whether we would should process more. The astute reader will
notice that the macro RING_REQUEST_CONS_OVERFLOW provides two
arguments - more on this later.
For example, if we were to enter this function with these values:
blk_rings->common.sring->req_prod = X+31415 (X is the value from
the last time __do_block_io_op was called).
blk_rings->common.req_cons = X
blk_rings->common.rsp_prod_pvt = X
The RING_REQUEST_CONS_OVERFLOW(&blk_rings->common, blk_rings->common.req_cons)
is doing:
req_cons - rsp_prod_pvt >= 32
Which is,
X - X >= 32 or 0 >= 32
And that is false, so we continue on looping (this bug).
If we re-use said macro RING_REQUEST_CONS_OVERFLOW and pass in the rp
instead (sring->req_prod) of rc, the this macro can do the check:
req_prod - rsp_prov_pvt >= 32
Which is,
X + 31415 - X >= 32 , or 31415 >= 32
which is true, so we can error out and break out of the function.
Unfortunatly the difference between rsp_prov_pvt and req_prod can be
at 32 (which would error out in the macro). This condition exists when
the backend is lagging behind with the responses and still has not finished
responding to all of them (so make_response has not been called), and
the rsp_prov_pvt + 32 == req_cons. This ends up with us not being able
to use said macro.
Hence introducing a new macro called RING_REQUEST_PROD_OVERFLOW which does
a simple check of:
req_prod - rsp_prod_pvt > RING_SIZE
And with the X values from above:
X + 31415 - X > 32
Returns true. Also not that if the ring is full (which is where
the RING_REQUEST_CONS_OVERFLOW triggered), we would not hit the
same condition:
X + 32 - X > 32
Which is false.
Lets use that macro.
Note that in v5 of this patchset the macro was different - we used an
earlier version.
[v1: Move the check outside the loop]
[v2: Add a pr_warn as suggested by David]
[v3: Use RING_REQUEST_CONS_OVERFLOW as suggested by Jan]
[v4: Move wake_up after kthread_stop as suggested by Jan]
[v5: Use RING_REQUEST_PROD_OVERFLOW instead]
[v6: Use RING_REQUEST_PROD_OVERFLOW - Jan's version]
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Reviewed-by: Jan Beulich <jbeulich@suse.com>
[bwh: Backported to 3.2: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Cc: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 03393fd5cc2b6cdeec32b704ecba64dbb0feae3c upstream.
Some frontend drivers are sending packets > 64 KiB in length. This length
overflows the length field in the first slot making the following slots have
an invalid length.
Turn this error back into a non-fatal error by dropping the packet. To avoid
having the following slots having fatal errors, consume all slots in the
packet.
This does not reopen the security hole in XSA-39 as if the packet as an
invalid number of slots it will still hit fatal error case.
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: Wei Liu <wei.liu2@citrix.com>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Cc: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 2810e5b9a7731ca5fce22bfbe12c96e16ac44b6f upstream.
This patch tries to coalesce tx requests when constructing grant copy
structures. It enables netback to deal with situation when frontend's
MAX_SKB_FRAGS is larger than backend's MAX_SKB_FRAGS.
With the help of coalescing, this patch tries to address two regressions
avoid reopening the security hole in XSA-39.
Regression 1. The reduction of the number of supported ring entries (slots)
per packet (from 18 to 17). This regression has been around for some time but
remains unnoticed until XSA-39 security fix. This is fixed by coalescing
slots.
Regression 2. The XSA-39 security fix turning "too many frags" errors from
just dropping the packet to a fatal error and disabling the VIF. This is fixed
by coalescing slots (handling 18 slots when backend's MAX_SKB_FRAGS is 17)
which rules out false positive (using 18 slots is legit) and dropping packets
using 19 to `max_skb_slots` slots.
To avoid reopening security hole in XSA-39, frontend sending packet using more
than max_skb_slots is considered malicious.
The behavior of netback for packet is thus:
1-18 slots: valid
19-max_skb_slots slots: drop and respond with an error
max_skb_slots+ slots: fatal error
max_skb_slots is configurable by admin, default value is 20.
Also change variable name from "frags" to "slots" in netbk_count_requests.
Please note that RX path still has dependency on MAX_SKB_FRAGS. This will be
fixed with separate patch.
Signed-off-by: Wei Liu <wei.liu2@citrix.com>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Cc: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 9eaee8beeeb3bca0d9b14324fd9d467d48db784c upstream.
Fix warning about 0 used as NULL.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Cc: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e6355ad7b1c6f70e2f48ae159f5658b441ccff95 upstream.
snd_pcm_stop() must be called in the PCM substream lock context.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
[wml: Backported to 3.4: Adjust filename]
Signed-off-by: Weng Meiling <wengmeiling.weng@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit c378f70adbc1bbecd9e6db145019f14b2f688c7c upstream.
Currently, when a disconnect is requested by the user (via NBD_DISCONNECT
ioctl) the return from NBD_DO_IT is undefined (it is usually one of
several error codes). This means that nbd-client does not know if a
manual disconnect was performed or whether a network error occurred.
Because of this, nbd-client's persist mode (which tries to reconnect after
error, but not after manual disconnect) does not always work correctly.
This change fixes this by causing NBD_DO_IT to always return 0 if a user
requests a disconnect. This means that nbd-client can correctly either
persist the connection (if an error occurred) or disconnect (if the user
requested it).
Signed-off-by: Paul Clements <paul.clements@steeleye.com>
Acked-by: Rob Landley <rob@landley.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
[xr: Backported to 3.4: adjust context]
Signed-off-by: Rui Xiang <rui.xiang@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e70ab977991964a5a7ad1182799451d067e62669 upstream.
While PROC_CN_MCAST_LISTEN/IGNORE is entirely advisory, it was possible
for an unprivileged user to turn off notifications for all listeners by
sending PROC_CN_MCAST_IGNORE. Instead, require the same privileges as
required for a multicast bind.
Signed-off-by: Kees Cook <keescook@chromium.org>
Cc: Evgeniy Polyakov <zbr@ioremap.net>
Cc: Matt Helsley <matthltc@us.ibm.com>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Acked-by: Matt Helsley <matthltc@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
[bwh: Backported to 3.2: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Cc: Qiang Huang <h.huangqiang@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a1989b330093578ea5470bea0a00f940c444c466 upstream.
An invalid ioctl will never be valid, irrespective of whether multipath
has active paths or not. So for invalid ioctls we do not have to wait
for multipath to activate any paths, but can rather return an error
code immediately. This fix resolves numerous instances of:
udevd[]: worker [] unexpectedly returned with status 0x0100
that have been seen during testing.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e9baa9d9d520fb0e24cca671e430689de2d4a4b2 upstream.
It appears that in the DMA40 driver the DMA tasklet will very
often dereference memory for a descriptor just free:d from the
DMA40 slab. Nothing happens because no other part of the driver
has yet had a chance to claim this memory, but it's really
nasty to dereference free:d memory, so let's check the flag
before the descriptor is free and store it in a bool variable.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 500a91571f0a5d0d3242d83802ea2fd1faccc66e upstream.
When trying to set the minimum temperature, the driver was erroneously
writing the maximum temperature into the chip.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 6dbd46c849e071e6afc1e0cad489b0175bca9318 upstream.
Hello,
the following patch adds an entry for the PID of a Cressi Leonardo
diving computer interface to kernel 3.13.0.
It is detected as FT232RL.
Works with subsurface.
Signed-off-by: Joerg Dorchain <joerg@dorchain.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 12df84d4a80278a5b1abfec3206795291da52fc9 upstream.
This interface is to be handled by the qmi_wwan driver.
CC: Hans-Christoph Schemmel <hans-christoph.schemmel@gemalto.com>
CC: Christian Schmiedl <christian.schmiedl@gemalto.com>
CC: Nicolaus Colberg <nicolaus.colberg@gemalto.com>
CC: David McCullough <david.mccullough@accelecon.com>
Signed-off-by: Aleksander Morgado <aleksander@aleksander.es>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f3ca4164529b875374c410193bbbac0ee960895f upstream.
acpi_processor_set_throttling() uses set_cpus_allowed_ptr() to make
sure that the (struct acpi_processor)->acpi_processor_set_throttling()
callback will run on the right CPU. However, the function may be
called from a worker thread already bound to a different CPU in which
case that won't work.
Make acpi_processor_set_throttling() use work_on_cpu() as appropriate
instead of abusing set_cpus_allowed_ptr().
Reported-and-tested-by: Jiri Olsa <jolsa@redhat.com>
Signed-off-by: Lan Tianyu <tianyu.lan@intel.com>
[rjw: Changelog]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
