summaryrefslogtreecommitdiff
path: root/net/dsa
AgeCommit message (Collapse)Author
2020-04-02net: dsa: Fix duplicate frames flooded by learningFlorian Fainelli
[ Upstream commit 0e62f543bed03a64495bd2651d4fe1aa4bcb7fe5 ] When both the switch and the bridge are learning about new addresses, switch ports attached to the bridge would see duplicate ARP frames because both entities would attempt to send them. Fixes: 5037d532b83d ("net: dsa: add Broadcom tag RX/TX handler") Reported-by: Maxime Bizon <mbizon@freebox.fr> Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-02-20net: dsa: slave: Don't propagate flag changes on down slave interfacesRundong Ge
[ Upstream commit 17ab4f61b8cd6f9c38e9d0b935d86d73b5d0d2b5 ] The unbalance of master's promiscuity or allmulti will happen after ifdown and ifup a slave interface which is in a bridge. When we ifdown a slave interface , both the 'dsa_slave_close' and 'dsa_slave_change_rx_flags' will clear the master's flags. The flags of master will be decrease twice. In the other hand, if we ifup the slave interface again, since the slave's flags were cleared the 'dsa_slave_open' won't set the master's flag, only 'dsa_slave_change_rx_flags' that triggered by 'br_add_if' will set the master's flags. The flags of master is increase once. Only propagating flag changes when a slave interface is up makes sure this does not happen. The 'vlan_dev_change_rx_flags' had the same problem and was fixed, and changes here follows that fix. Fixes: 91da11f870f0 ("net: Distributed Switch Architecture protocol support") Signed-off-by: Rundong Ge <rdong.ge@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-08-06net: dsa: Do not suspend/resume closed slave_devFlorian Fainelli
[ Upstream commit a94c689e6c9e72e722f28339e12dff191ee5a265 ] If a DSA slave network device was previously disabled, there is no need to suspend or resume it. Fixes: 2446254915a7 ("net: dsa: allow switch drivers to implement suspend/resume hooks") Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-11-15net: dsa: select NET_SWITCHDEVVivien Didelot
[ Upstream commit 3a89eaa65db68bf53bf92dedc60084f810e1779a ] The support for DSA Ethernet switch chips depends on TCP/IP networking, thus explicit that HAVE_NET_DSA depends on INET. DSA uses SWITCHDEV, thus select it instead of depending on it. Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Tested-by: Randy Dunlap <rdunlap@infradead.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-07-05net: dsa: Check return value of phy_connect_direct()Florian Fainelli
[ Upstream commit 4078b76cac68e50ccf1f76a74e7d3d5788aec3fe ] We need to check the return value of phy_connect_direct() in dsa_slave_phy_connect() otherwise we may be continuing the initialization of a slave network device with a PHY that already attached somewhere else and which will soon be in error because the PHY device is in error. The conditions for such an error to occur are that we have a port of our switch that is not disabled, and has the same port number as a PHY address (say both 5) that can be probed using the DSA slave MII bus. We end-up having this slave network device find a PHY at the same address as our port number, and we try to attach to it. A slave network (e.g: port 0) has already attached to our PHY device, and we try to re-attach it with a different network device, but since we ignore the error we would end-up initializating incorrect device references by the time the slave network interface is opened. The code has been (re)organized several times, making it hard to provide an exact Fixes tag, this is a bugfix nonetheless. Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-02-04net: dsa: Bring back device detaching in dsa_slave_suspend()Florian Fainelli
[ Upstream commit f154be241d22298d2b63c9b613f619fa1086ea75 ] Commit 448b4482c671 ("net: dsa: Add lockdep class to tx queues to avoid lockdep splat") removed the netif_device_detach() call done in dsa_slave_suspend() which is necessary, and paired with a corresponding netif_device_attach(), bring it back. Fixes: 448b4482c671 ("net: dsa: Add lockdep class to tx queues to avoid lockdep splat") Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-11-01net: dsa: use switchdev obj for VLAN add/del opsVivien Didelot
Simplify DSA by pushing the switchdev objects for VLAN add and delete operations down to its drivers. Currently only mv88e6xxx is affected. Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-10-22net: dsa: remove port_fdb_getnextVivien Didelot
No driver implements port_fdb_getnext anymore, and port_fdb_dump is preferred anyway, so remove this function from DSA. Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-10-22net: dsa: add port_fdb_dump functionVivien Didelot
Not all switch chips support a Get Next operation to iterate on its FDB. So add a more simple port_fdb_dump function for them. Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-10-20Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netDavid S. Miller
Conflicts: drivers/net/usb/asix_common.c net/ipv4/inet_connection_sock.c net/switchdev/switchdev.c In the inet_connection_sock.c case the request socket hashing scheme is completely different in net-next. The other two conflicts were overlapping changes. Signed-off-by: David S. Miller <davem@davemloft.net>
2015-10-15switchdev: remove pointers from switchdev objectsJiri Pirko
When object is used in deferred work, we cannot use pointers in switchdev object structures because the memory they point at may be already used by someone else. So rather do local copy of the value. Signed-off-by: Jiri Pirko <jiri@mellanox.com> Acked-by: Scott Feldman <sfeldma@gmail.com> Reviewed-by: John Fastabend <john.r.fastabend@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-10-15switchdev: make struct switchdev_attr parameter const for attr_set callsJiri Pirko
Signed-off-by: Jiri Pirko <jiri@mellanox.com> Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-10-13net: dsa: do not warn unsupported bridge opsVivien Didelot
A DSA driver may not provide the port_join_bridge and port_leave_bridge functions, so don't warn in such case. Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-10-11net: dsa: use switchdev obj in port_fdb_delVivien Didelot
For consistency with the FDB add operation, propagate the switchdev_obj_port_fdb structure in the DSA drivers. Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com> Reviewed-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-10-11net: dsa: push prepare phase in port_fdb_addVivien Didelot
Now that the prepare phase is pushed down to the DSA drivers, propagate it to the port_fdb_add function. Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com> Reviewed-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-10-11net: dsa: add port_fdb_prepareVivien Didelot
Push the prepare phase for FDB operations down to the DSA drivers, with a new port_fdb_prepare function. Currently only mv88e6xxx is affected. Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com> Reviewed-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-10-07net: dsa: exit probe if no switch were foundNeil Armstrong
If no switch were found in dsa_setup_dst, return -ENODEV and exit the dsa_probe cleanly. Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-10-07net: dsa: switch to devm_ calls and remove kfree callsNeil Armstrong
Now the kfree calls exists in the the remove functions, remove them in all places except the of_probe functions and replace allocation calls with their devm_ counterparts. Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-10-07net: dsa: complete dsa_switch_destroyNeil Armstrong
When unbinding dsa, complete the dsa_switch_destroy to unregister the fixed link phy then cleanly unregister and destroy the net devices. Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-10-07net: dsa: add missing dsa_switch mdiobus removeNeil Armstrong
To prevent memory leakage on unbinding, add missing mdiobus unregister and unallocation calls. Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-10-07net: dsa: add missing kfree on removeNeil Armstrong
To prevent memory leakage on unbinding, add missing kfree calls. Includes minor cosmetic change to make patch clean. Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-10-07net: dsa: better error reportingRussell King
Add additional error reporting to the generic DSA code, so it's easier to debug when things go wrong. This was useful when initially bringing up 88e6176 on a new board. Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Acked-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-10-03switchdev: push object ID back to object structureJiri Pirko
Suggested-by: Scott Feldman <sfeldma@gmail.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Acked-by: Scott Feldman <sfeldma@gmail.com> Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-10-03switchdev: bring back switchdev_obj and use it as a generic object paramJiri Pirko
Replace "void *obj" with a generic structure. Introduce couple of helpers along that. Signed-off-by: Jiri Pirko <jiri@mellanox.com> Acked-by: Scott Feldman <sfeldma@gmail.com> Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-10-03switchdev: rename switchdev_obj_fdb to switchdev_obj_port_fdbJiri Pirko
Make the struct name in sync with object id name. Suggested-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Acked-by: Scott Feldman <sfeldma@gmail.com> Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-10-03switchdev: rename switchdev_obj_vlan to switchdev_obj_port_vlanJiri Pirko
Make the struct name in sync with object id name. Suggested-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Acked-by: Scott Feldman <sfeldma@gmail.com> Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-10-03switchdev: rename SWITCHDEV_ATTR_* enum values to SWITCHDEV_ATTR_ID_*Jiri Pirko
To be aligned with obj. Signed-off-by: Jiri Pirko <jiri@mellanox.com> Acked-by: Scott Feldman <sfeldma@gmail.com> Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-10-03switchdev: rename SWITCHDEV_OBJ_* enum values to SWITCHDEV_OBJ_ID_*Jiri Pirko
Suggested-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Acked-by: Scott Feldman <sfeldma@gmail.com> Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-09-29net: dsa: fix preparation of a port STP updateVivien Didelot
Because of the default 0 value of ret in dsa_slave_port_attr_set, a driver may return -EOPNOTSUPP from the commit phase of a STP state, which triggers a WARN() from switchdev. This happened on a 6185 switch which does not support hardware bridging. Fixes: 3563606258cf ("switchdev: convert STP update to switchdev attr set") Reported-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-09-29net: dsa: fix preparation of a port STP updateVivien Didelot
Because of the default 0 value of ret in dsa_slave_port_attr_set, a driver may return -EOPNOTSUPP from the commit phase of a STP state, which triggers a WARN() from switchdev. This happened on a 6185 switch which does not support hardware bridging. Reported-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com> Acked-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-09-29net: switchdev: abstract object in add/del opsVivien Didelot
Similar to the notifier_call callback of a notifier_block, change the function signature of switchdev add and del operations to: int switchdev_port_obj_add/del(struct net_device *dev, enum switchdev_obj_id id, void *obj); This allows the caller to pass a specific switchdev_obj_* structure instead of the generic switchdev_obj one. Drivers implementation of these operations and switchdev have been changed accordingly. Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-09-29net: switchdev: pass callback to dump operationVivien Didelot
Similar to the notifier_call callback of a notifier_block, change the function signature of switchdev dump operation to: int switchdev_port_obj_dump(struct net_device *dev, enum switchdev_obj_id id, void *obj, int (*cb)(void *obj)); This allows the caller to pass and expect back a specific switchdev_obj_* structure instead of the generic switchdev_obj one. Drivers implementation of dump operation can now expect this specific structure and call the callback with it. Drivers have been changed accordingly. Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-09-29net: switchdev: remove dev from switchdev_obj cbVivien Didelot
The net_device associated to a dump operation does not have to be passed to the callback. switchdev stores it in a superset struct, if needed. Also some drivers (such as DSA drivers) may not have easy access to it. This will simplify pushing the callback function down to the drivers. Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-09-26Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netDavid S. Miller
Conflicts: net/ipv4/arp.c The net/ipv4/arp.c conflict was one commit adding a new local variable while another commit was deleting one. Signed-off-by: David S. Miller <davem@davemloft.net>
2015-09-25net: dsa: Set a "dsa" device_typeFlorian Fainelli
Provide a device_type information for slave network devices created by DSA, this is useful for user-space application to easily locate/search for devices of a specific kind. Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-09-24net: fix net_device refcountingRussell King
of_find_net_device_by_node() uses class_find_device() internally to lookup the corresponding network device. class_find_device() returns a reference to the embedded struct device, with its refcount incremented. Add a comment to the definition in net/core/net-sysfs.c indicating the need to drop this refcount, and fix the DSA code to drop this refcount when the OF-generated platform data is cleaned up and freed. Also arrange for the ref to be dropped when handling errors. Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-09-24net: dsa: fix of_mdio_find_bus() device refcount leakRussell King
Current users of of_mdio_find_bus() leak a struct device refcount, as they fail to clean up the reference obtained inside class_find_device(). Fix the DSA code to properly refcount the returned MDIO bus by: 1. taking a reference on the struct device whenever we assign it to pd->chip[x].host_dev. 2. dropping the reference when we overwrite the existing reference. 3. dropping the reference when we free the data structure. 4. dropping the initial reference we obtained after setting up the platform data structure, or on failure. In step 2 above, where we obtain a new MDIO bus, there is no need to take a reference on it as we would only have to drop it immediately after assignment again, iow: put_device(cd->host_dev); /* drop original assignment ref */ cd->host_dev = get_device(&mdio_bus_switch->dev); /* get our ref */ put_device(&mdio_bus_switch->dev); /* drop of_mdio_find_bus ref */ Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-09-24dsa: use prepare/commit switchdev transaction helpersJiri Pirko
The enum is going to disappear, use the helpers instead. Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-09-24switchdev: move transaction phase enum under transaction structureJiri Pirko
Before it disappears completely, move transaction phase enum under transaction structure and make attr/obj structures a bit cleaner. Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-09-24switchdev: introduce transaction item queue for attr_set and obj_addJiri Pirko
Now, the memory allocation in prepare/commit state is done separatelly in each driver (rocker). Introduce the similar mechanism in generic switchdev code, in form of queue. That can be used not only for memory allocations, but also for different items. Abort item destruction is handled as well. Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-09-24switchdev: rename "trans" to "trans_ph".Jiri Pirko
This is temporary, name "trans" will be used for something else and "trans_ph" will eventually disappear. Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-09-22net: dsa: Fix Marvell Egress Trailer checkNeil Armstrong
The Marvell Egress rx trailer check must be fixed to correctly detect bad bits in the third byte of the Eggress trailer as described in the Table 28 of the 88E6060 datasheet. The current code incorrectly omits to check the third byte and checks the fourth byte twice. Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Acked-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-08-31net: dsa: Allow DSA and CPU ports to have a phy-mode propertyAndrew Lunn
It can be useful for DSA and CPU ports to have a phy-mode property, in particular to specify RGMII delays. Parse the property and set it in the fixed-link phydev. Signed-off-by: Andrew Lunn <andrew@lunn.ch> Acked-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-08-31net: dsa: Allow configuration of CPU & DSA port speeds/duplexAndrew Lunn
By default, DSA and CPU ports are configured to the maximum speed the switch supports. However there can be use cases where the peer devices port is slower. Allow a fixed-link property to be used with the DSA and CPU port in the device tree, and use this information to configure the port. Signed-off-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-08-18net: dsa: Allow multi hop routes to be expressedAndrew Lunn
With more than two switches in a hierarchy, it becomes necessary to describe multi-hop routes between switches. The current binding does not allow this, although the older platform_data did. Extend the link property to be a list rather than a single phandle to a remote switch. It is then possible to express that a port should be used to reach more than one switch and the switch maybe more than one hop away. Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-08-18net: dsa: convert to using IFF_NO_QUEUEPhil Sutter
Signed-off-by: Phil Sutter <phil@nwl.cc> Cc: Lennert Buytenhek <buytenh@wantstofly.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-08-13net: dsa: add support for switchdev VLAN objectsVivien Didelot
Add new functions in DSA drivers to access hardware VLAN entries through SWITCHDEV_OBJ_PORT_VLAN objects: - port_pvid_get() and vlan_getnext() to dump a VLAN - port_vlan_del() to exclude a port from a VLAN - port_pvid_set() and port_vlan_add() to join a port to a VLAN The DSA infrastructure will ensure that each VLAN of the given range does not already belong to another bridge. If it does, it will fallback to software VLAN and won't program the hardware. Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-08-13Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netDavid S. Miller
Conflicts: drivers/net/ethernet/cavium/Kconfig The cavium conflict was overlapping dependency changes. Signed-off-by: David S. Miller <davem@davemloft.net>
2015-08-12net: dsa: Do not override PHY interface if already configuredFlorian Fainelli
In case we need to divert reads/writes using the slave MII bus, we may have already fetched a valid PHY interface property from Device Tree, and that mode is used by the PHY driver to make configuration decisions. If we could not fetch the "phy-mode" property, we will assign p->phy_interface to PHY_INTERFACE_MODE_NA, such that we can actually check for that condition as to whether or not we should override the interface value. Fixes: 19334920eaf7 ("net: dsa: Set valid phy interface type") Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-08-11net: dsa: add support for switchdev FDB objectsVivien Didelot
Implement the switchdev_port_obj_{add,del,dump} functions in DSA to support the SWITCHDEV_OBJ_PORT_FDB objects. Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com> Signed-off-by: David S. Miller <davem@davemloft.net>
generated by cgit v1.2.3 (git 2.0.4) at 2024-05-12 09:35:28 +0000