| Age | Commit message (Collapse) | Author |
|---|
|
This is the 5.0.19 stable release
|
|
This is the 5.0.17 stable release
|
|
commit 01c8327667c249818d3712c3e25c7ad2aca7f389 upstream.
In resume from S3, HDAC HDMI codec driver dapm event callback may be
operated before HDMI codec driver turns on the display audio power
domain because of the contest between display driver and hdmi codec driver.
This patch adds the device_link between soc card device (consumer) and
hdmi codec device (supplier) to make sure the sequence is always correct.
Signed-off-by: Libin Yang <libin.yang@intel.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 903c220b1ece12f17c868e43f2243b8f81ff2d4c upstream.
case ESAI_HCKT_EXTAL and case ESAI_HCKR_EXTAL should be
independent of each other, so replace fall-through with break.
Fixes: 43d24e76b698 ("ASoC: fsl_esai: Add ESAI CPU DAI driver")
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a46eb523220e242affb9a6bc9bb8efc05f4f7459 upstream.
The current algorithm allows 3 types of transfers, 16bit, 32bit and
burst. According to Realtek, 16bit transfers have a special restriction
in that it is restricted to the memory region of
0x18020000 ~ 0x18021000. This region is the memory location of the I2C
registers. The current algorithm does not uphold this restriction and
therefore fails to complete writes.
Since this has been broken for some time it likely no one is using it.
Better to simply disable the 16 bit writes. This will allow users to
properly load firmware over SPI without data corruption.
Signed-off-by: Curtis Malainey <cujomalainey@chromium.org>
Reviewed-by: Ben Zhang <benzh@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ecb2795c08bc825ebd604997e5be440b060c5b18 upstream.
The max98090 driver defines 3 DAPM muxes; one for the right line output
(LINMOD Mux), one for the left headphone mixer source (MIXHPLSEL Mux)
and one for the right headphone mixer source (MIXHPRSEL Mux). The same
bit is used for the mux as well as the DAPM enable, and although the mux
can be correctly configured, after playback has completed, the mux will
be reset during the disable phase. This is preventing the state of these
muxes from being saved and restored correctly on system reboot. Fix this
by marking these muxes as SND_SOC_NOPM.
Note this has been verified this on the Tegra124 Nyan Big which features
the MAX98090 codec.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 0efa3334d65b7f421ba12382dfa58f6ff5bf83c4 upstream.
Currently in sst_dsp_new() if we get an error return from sst_dma_new()
we just print an error message and then still complete the function
successfully. This means that we are trying to run without sst->dma
properly set up, which will result in NULL pointer dereference when
sst->dma is later used. This was happening for me in
sst_dsp_dma_get_channel():
struct sst_dma *dma = dsp->dma;
...
dma->ch = dma_request_channel(mask, dma_chan_filter, dsp);
This resulted in:
BUG: unable to handle kernel NULL pointer dereference at 0000000000000018
IP: sst_dsp_dma_get_channel+0x4f/0x125 [snd_soc_sst_firmware]
Fix this by adding proper error handling for the case where we fail to
set up DMA.
This change only affects Haswell and Broadwell systems. Baytrail
systems explicilty opt-out of DMA via sst->pdata->resindex_dma_base
being set to -1.
Signed-off-by: Ross Zwisler <zwisler@google.com>
Cc: stable@vger.kernel.org
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit e37c2deafe7058cf7989c4c47bbf1140cc867d89 ]
When master clock is used, master clock rate is set exclusively.
Parent clocks of master clock cannot be changed after a call to
clk_set_rate_exclusive(). So the parent clock of SAI kernel clock
must be set before.
Ensure also that exclusive rate operations are balanced
in STM32 SAI driver.
Signed-off-by: Olivier Moysan <olivier.moysan@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit d6ba3f815bc5f3c4249d15c8bc5fbb012651b4a4 ]
Fix wrong setting on number of channels. The context wants to set
constraint to 2 channels instead of 4.
Signed-off-by: Tzung-Bi Shih <tzungbi@google.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 47c4cc08cb5b34e93ab337b924c5ede77ca3c936 ]
The chips main power supplies VA and VP are enabled during probe but
then never disabled, this will cause warnings from the regulator
framework on driver removal. Fix this by adding a remove callback and
disabling the supplies, whilst doing so follow best practice and put the
chip back into reset as well.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit c85064435fe7a216ec0f0238ef2b8f7cd850a450 ]
This is because set_fmt ops maybe called when PD is off,
and in such case, regmap_ops will lead system hang.
enale PD before doing regmap_ops.
Signed-off-by: Sugar Zhang <sugar.zhang@rock-chips.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit c63adb28f6d913310430f14c69f0a2ea55eed0cc ]
The common pins were mistakenly not added to the DAPM graph.
Adding these pins will allow valid graphs to be created.
Signed-off-by: Annaliese McDermond <nh6z@nh6z.net>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit cacea3a90e211f0c111975535508d446a4a928d2 ]
w_text_param can be NULL and it is being dereferenced without checking.
Add the missing sanity check to prevent NULL pointer dereference.
Signed-off-by: Pankaj Bharadiya <pankaj.laxminarayan.bharadiya@intel.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit f0f2338a9cfaf71db895fa989ea7234e8a9b471d ]
The CS4270 does not by default increment the register address on
consecutive writes. During normal operation it doesn't matter as all
register accesses are done individually. At resume time after suspend,
however, the regcache code gathers the biggest possible block of
registers to sync and sends them one on one go.
To fix this, set the INCR bit in all cases.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit c47255b61129857b74b0d86eaf59335348be05e0 ]
Register platform component with a prefix, to avoid warnings
on debugfs entries creation, due to component name
redundancy.
Signed-off-by: Olivier Moysan <olivier.moysan@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 19441e35a43b616ea6afad91ed0d9e77268d8f6a ]
The DFSDM must be stopped when a new setting is applied.
restart systematically DFSDM on multiple prepare calls,
to apply changes.
Signed-off-by: Olivier Moysan <olivier.moysan@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit a2225a6d155fcb247fe4c6d87f7c91807462966d ]
Best to lock across handling the bus error to ensure the DSP doesn't
change power state as we are reading the status registers.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 1c5b6a27e432e4fe170a924c8b41012271496a4c ]
If ASRC turns on, HW will use clk_dac as the reference clock
whether recording or playback.
Both of clk_dac and clk_adc should set proper clock while using ASRC.
Signed-off-by: Shuming Fan <shumingf@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 675212bfb23394514b7f68ebf3954ba936281ccc ]
The jack type detection needs the main bias power of analog.
The modification makes sure the main bias power on/off while jack plug/unplug.
Signed-off-by: Shuming Fan <shumingf@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 4834d7070c85a5fb69637265dbbb05d13043280c ]
The IRQ function may not work when system suspend.
We remove snd_soc_dapm_force_enable_pin function call to
make sure the bias off when idle and run into suspend/resume function.
Signed-off-by: Shuming Fan <shumingf@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 2b13bee3884926cba22061efa75bd315e871de24 ]
After commit fbeec965b8d1c ("ASoC: samsung: odroid: Fix 32000 sample rate
handling") the audio root clock frequency is configured improperly for
44100 sample rate. Due to clock rate rounding it's 20070401 Hz instead
of 22579000 Hz. This results in a too low value of the PSR clock divider
in the CPU DAI driver and too fast actual sample rate for fs=44100. E.g.
1 kHz tone has actual 1780 Hz frequency (1 kHz * 20070401/22579000 * 2).
Fix this by increasing the correction passed to clk_set_rate() to take
into account inaccuracy of the EPLL frequency properly.
Fixes: fbeec965b8d1c ("ASoC: samsung: odroid: Fix 32000 sample rate handling")
Reported-by: JaeChul Lee <jcsing.lee@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 54d1cf78b0f4ba348a7c7fb8b7d0708d71b6cc8a ]
The driver changes the stream name of DAC and ADC to avoid the issue of
widget with prefixed name. When the machine adds prefixed name for codec,
the stream name of DAI may not find the widgets.
Signed-off-by: John Hsu <KCHSU0@nuvoton.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 844a4a362dbec166b44d6b9b3dd45b08cb273703 ]
The driver has two issues when machine add prefix name for codec.
(1)The stream name of DAI can't find the AIF widgets.
(2)The drivr can enable/disalbe the MICBIAS and SAR widgets.
The patch will fix these issues caused by prefixed name added.
Signed-off-by: John Hsu <KCHSU0@nuvoton.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit a9764869779081e8bf24da07ac040e8f3efcf13a ]
The dpcm get from fe_clients/be_clients
may be free before use
Add a spin lock at snd_soc_card level,
to protect the dpcm instance.
The lock may be used in atomic context, so use spin lock.
Use irq spin lock version,
since the lock may be used in interrupts.
possible race condition between
void dpcm_be_disconnect(
...
list_del(&dpcm->list_be);
list_del(&dpcm->list_fe);
kfree(dpcm);
...
and
for_each_dpcm_fe()
for_each_dpcm_be*()
race condition example
Thread 1:
snd_soc_dapm_mixer_update_power()
-> soc_dpcm_runtime_update()
-> dpcm_be_disconnect()
-> kfree(dpcm);
Thread 2:
dpcm_fe_dai_trigger()
-> dpcm_be_dai_trigger()
-> snd_soc_dpcm_can_be_free_stop()
-> if (dpcm->fe == fe)
Excpetion Scenario:
two FE link to same BE
FE1 -> BE
FE2 ->
Thread 1: switch of mixer between FE2 -> BE
Thread 2: pcm_stop FE1
Exception:
Unable to handle kernel paging request at virtual address dead0000000000e0
pc=<> [<ffffff8960e2cd10>] dpcm_be_dai_trigger+0x29c/0x47c
sound/soc/soc-pcm.c:3226
if (dpcm->fe == fe)
lr=<> [<ffffff8960e2f694>] dpcm_fe_dai_do_trigger+0x94/0x26c
Backtrace:
[<ffffff89602dba80>] notify_die+0x68/0xb8
[<ffffff896028c7dc>] die+0x118/0x2a8
[<ffffff89602a2f84>] __do_kernel_fault+0x13c/0x14c
[<ffffff89602a27f4>] do_translation_fault+0x64/0xa0
[<ffffff8960280cf8>] do_mem_abort+0x4c/0xd0
[<ffffff8960282ad0>] el1_da+0x24/0x40
[<ffffff8960e2cd10>] dpcm_be_dai_trigger+0x29c/0x47c
[<ffffff8960e2f694>] dpcm_fe_dai_do_trigger+0x94/0x26c
[<ffffff8960e2edec>] dpcm_fe_dai_trigger+0x3c/0x44
[<ffffff8960de5588>] snd_pcm_do_stop+0x50/0x5c
[<ffffff8960dded24>] snd_pcm_action+0xb4/0x13c
[<ffffff8960ddfdb4>] snd_pcm_drop+0xa0/0x128
[<ffffff8960de69bc>] snd_pcm_common_ioctl+0x9d8/0x30f0
[<ffffff8960de1cac>] snd_pcm_ioctl_compat+0x29c/0x2f14
[<ffffff89604c9d60>] compat_SyS_ioctl+0x128/0x244
[<ffffff8960283740>] el0_svc_naked+0x34/0x38
[<ffffffffffffffff>] 0xffffffffffffffff
Signed-off-by: KaiChieh Chuang <kaichieh.chuang@mediatek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit c899df3e9b0bf7b76e642aed1a214582ea7012d5 ]
If playback and capture are enabled concurrently, when the capture stops
the output becomes inaudile. The playback application will become stuck
and underrun after a timeout.
This is caused by mistaken use of the stream_id, which should only be
set for playback and not for capture
Tested on Apollolake and Kabylake with SST driver.
Signed-off-by: Rander Wang <rander.wang@linux.intel.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 03d0aa4d4fddce4a5d865d819a4d98bfc3d451e6 ]
The current implementation of the hdac_hda codec results in zero-valued
samples on capture and noise with headset playback when SOF is used on
platforms with an on-board HDaudio codec. This is root-caused to SOF
using be_hw_params_fixup, and the prepare() call using invalid runtime
fields to determine the format.
This patch moves the format handling to the hw_params() callback, as
done already for hdac_hdmi, to make sure the fixed-up information is
taken into account but keeps the codec initialization in prepare() as
the stream_tag is only available at that time. Moving everything in the
prepare() callback is possible but the code is less elegant so this
two-step solution was chosen.
The solution was tested with the SST driver with no regressions, and all
the issues with SOF playback and capture are solved.
Signed-off-by: Rander Wang <rander.wang@linux.intel.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 570f18b6a8d1f0e60e8caf30e66161b6438dcc91 ]
On HDaudio platforms, if playback is started when capture is working,
there is no audible output.
This can be root-caused to the use of the rx|tx_mask to store an HDaudio
stream tag.
If capture is stared before playback, rx_mask would be non-zero on HDaudio
platform, then the channel number of playback, which is in the same codec
dai with the capture, would be changed by soc_pcm_codec_params_fixup based
on the tx_mask at first, then overwritten by this function based on rx_mask
at last.
According to the author of tx|rx_mask, tx_mask is for playback and rx_mask
is for capture. And stream direction is checked at all other references of
tx|rx_mask in ASoC, so here should be an error. This patch checks stream
direction for tx|rx_mask for fixup function.
This issue would affect not only HDaudio+ASoC, but also I2S codecs if the
channel number based on rx_mask is not equal to the one for tx_mask. It could
be rarely reproduecd because most drivers in kernel set the same channel number
to tx|rx_mask or rx_mask is zero.
Tested on all platforms using stream_tag & HDaudio and intel I2S platforms.
Signed-off-by: Rander Wang <rander.wang@linux.intel.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 26f98e82dd49b7c3cc5ef0edd882aa732a62b672 ]
When snd_pcm_stop_xrun() is called in interrupt routine,
substream context may have already been released.
Add protection on substream context.
Signed-off-by: Olivier Moysan <olivier.moysan@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit b8468192971807c43a80d6e2c41f83141cb7b211 ]
Change capabilities exposed in SAI S/PDIF mode, to match
actually supported formats.
In S/PDIF mode only 32 bits stereo is supported.
Signed-off-by: Olivier Moysan <olivier.moysan@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 5f8a1000c3e630c3ac06f1d664eeaa755bce8823 ]
Allow indexation of sai iec958 controls according
to device id.
Signed-off-by: Olivier Moysan <olivier.moysan@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 2e95f984aae4cf0608d0ba2189c756f2bd50b44a ]
When using the S/PDIF DAI, there is no requirement to call
snd_soc_dai_set_fmt() as there is no DAI format definition that defines
S/PDIF. In any case, S/PDIF does not have separate clocks, this is
embedded into the data stream.
Consequently, when attempting to use TDA998x in S/PDIF mode, the attempt
to configure TDA998x via the hw_params callback fails as the
hdmi_codec_daifmt is left initialised to zero.
Since the S/PDIF DAI will only be used by S/PDIF, prepare the
hdmi_codec_daifmt structure for this format.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 82ad759143ed77673db0d93d53c1cde7b99917ee ]
This patch fixes a bug that prevents freeing the reset gpio on unloading
the module.
aic3x_i2c_probe is called when loading the module and it calls list_add
with a probably uninitialized list entry aic3x->list (next = prev = NULL)).
So even if list_del is called it does nothing and in the end the gpio_reset
is not freed. Then a repeated module probing fails silently because
gpio_request fails.
When moving INIT_LIST_HEAD to aic3x_i2c_probe we also have to move
list_del to aic3x_i2c_remove because aic3x_remove may be called
multiple times without aic3x_i2c_remove being called which leads to
a NULL pointer dereference.
Signed-off-by: Philipp Puschmann <philipp.puschmann@emlix.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 43d147be5738a9ed6cfb25c285ac50d6dd5793be upstream.
Trigger stop can be called in situations where trigger start failed
and as such it can't be assumed the buffer is already attached to
the compressed stream or a NULL pointer may be dereferenced.
Fixes: 639e5eb3c7d6 ("ASoC: wm_adsp: Correct handling of compressed streams that restart")
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: Nobuhiro Iwamatsu <nobuhiro1.iwamatsu@toshiba.co.jp>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 17d3069ccf06970e2db3f7cbf4335f207524279e upstream.
This patch fixes the sai driver structure overwriting which results in
a cpu dai name equal NULL.
Fixes: 3e086ed ("ASoC: stm32: add SAI driver")
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 6246f283d5e02ac757bd8d9bacde8fdc54c4582d upstream.
If for any reason, the backend does not have the requested substream
(like capture on a playback only backend), the BE will be skipped in
dpcm_be_dai_startup().
However, dpcm_apply_symmetry() does not skip those BE and will
dereference the be_substream (NULL) pointer anyway.
Like in dpcm_be_dai_startup(), just skip those BE.
Fixes: 906c7d690c3b ("ASoC: dpcm: Apply symmetry for DPCM")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 639e5eb3c7d67e407f2a71fccd95323751398f6f upstream.
Previously support was added to allow streams to be stopped and
started again without the DSP being power cycled and this was done
by clearing the buffer state in trigger start. Another supported
use-case is using the DSP for a trigger event then opening the
compressed stream later to receive the audio, unfortunately clearing
the buffer state in trigger start destroys the data received
from such a trigger. Correct this issue by moving the call to
wm_adsp_buffer_clear to be in trigger stop instead.
Fixes: 61fc060c40e6 ("ASoC: wm_adsp: Support streams which can start/stop with DSP active")
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 5fd812e6f5ae0376134234ceb70e8de541ccb10d upstream.
The A64 datasheet lists the supply rail for the headphone amp's charge
pump as "CPVDD". cpvdd-supply is the name of the property for this power
rail specified in the device tree bindings. "HPVCC" was the name used in
the A33 datasheet for the same function.
Rename the supply so it matches the datasheet, bindings, and the subject
from the original commit.
Fixes: ca0412a05756 ("ASoC: sunxi: sun50i-codec-analog: Add support for cpvdd regulator supply")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 8af6c521cc236534093f9e744cfa004314bfe5ae upstream.
Currently each SSI unit 's busif mode/adinr/dalign address is
registered by: (in busif4 case)
RSND_GEN_M_REG(SSI_BUSIF4_MODE, 0x500, 0x80)
RSND_GEN_M_REG(SSI_BUSIF4_ADINR,0x504, 0x80)
RSND_GEN_M_REG(SSI_BUSIF4_DALIGN, 0x508, 0x80)
But according to user manual 41.1.4 Register Configuration
ssi9 4/5/6/7 busif mode/adinr/dalign register address
( SSI9-[4/5/6/7]_BUSIF_[MODE/ADINR/DALIGN] )
are out of this rule.
This patch registers ssi9 4/5/6/7 mode/adinr/dalign register
as single register, and access these registers in case of
SSI9 BUSIF 4/5/6/7.
Fixes: commit 8c9d75033340 ("ASoC: rsnd: ssiu: Support BUSIF other than BUSIF0")
Signed-off-by: Jiada Wang <jiada_wang@mentor.com>
Signed-off-by: Timo Wischer <twischer@de.adit-jv.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit aee48a9ffa5a128bf4e433c57c39e015ea5b0208 upstream.
Commit 37c7401e8c1f ("ASoC: Intel: bytcr_rt5651: Fix DMIC map
headsetmic mapping"), changed the headsetmic mapping from IN3P to IN2P,
this was based on the observation that all bytcr_rt5651 devices I have
access to (7 devices) where all using IN3P for the headsetmic. This was
an attempt to unifify / simplify the mapping, but it was wrong.
None of those devices was actually using a digital internal mic. Now I've
access to a Point of View TAB-P1006W-232 (v1.0) tabler, which does use a
DMIC and it does have its headsetmic connected to IN2P, showing that the
original mapping was correct, so this commit reverts the change changing
the mapping back to IN2P.
Fixes: 37c7401e8c1f ("ASoC: Intel: bytcr_rt5651: Fix DMIC map ... mapping")
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Deferred probes shouldn't cause error messages in the boot log, so
change the dev_err() to the more harmless dev_info().
Signed-off-by: Stefan Agner <stefan@agner.ch>
|
|
Probe deferral is to be expected during normal operation, so avoid
printing an error when it is encountered.
Removing the goto would not be strictly necessary. However, if
code gets added later, the cleanup in the EPROBE_DEFER case likely
would get missed.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
|
|
Probe deferral is to be expected during normal operation, so avoid
printing an error when it is encountered.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
|
|
Probe deferral is to be expected during normal operation, so avoid
printing an error when it is encountered.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
|
|
Not finding the codec/SSI instance can be due to probe deferral.
Do not print error messages in those cases.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
|
|
Make sure to properly put the of node in case finding the codec
fails.
Fixes: 81e8e4926167 ("ASoC: fsl: add sgtl5000 clock support for imx-sgtl5000")
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
|
|
commit 0ff4e8c61b794a4bf6c854ab071a1abaaa80f358 upstream.
There is very low possibility ( < 0.1% ) that channel swap happened
in beginning when multi output/input pin is enabled. The issue is
that hardware can't send data to correct pin in the beginning with
the normal enable flow.
This is hardware issue, but there is no errata, the workaround flow
is that: Each time playback/recording, firstly clear the xSMA/xSMB,
then enable TE/RE, then enable xSMB and xSMA (xSMB must be enabled
before xSMA). Which is to use the xSMA as the trigger start register,
previously the xCR_TE or xCR_RE is the bit for starting.
Fixes commit 43d24e76b698 ("ASoC: fsl_esai: Add ESAI CPU DAI driver")
Cc: <stable@vger.kernel.org>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 8f71370f4b02730e8c27faf460af7a3586e24e1f upstream.
If codec registration fails after the ASoC Intel SST driver has been probed,
the kernel will Oops and crash at suspend/resume.
general protection fault: 0000 [#1] PREEMPT SMP KASAN PTI
CPU: 1 PID: 2811 Comm: cat Tainted: G W 4.19.30 #15
Hardware name: GOOGLE Clapper, BIOS Google_Clapper.5216.199.7 08/22/2014
RIP: 0010:snd_soc_suspend+0x5a/0xd21
Code: 03 80 3c 10 00 49 89 d7 74 0b 48 89 df e8 71 72 c4 fe 4c 89
fa 48 8b 03 48 89 45 d0 48 8d 98 a0 01 00 00 48 89 d8 48 c1 e8 03
<8a> 04 10 84 c0 0f 85 85 0c 00 00 80 3b 00 0f 84 6b 0c 00 00 48 8b
RSP: 0018:ffff888035407750 EFLAGS: 00010202
RAX: 0000000000000034 RBX: 00000000000001a0 RCX: 0000000000000000
RDX: dffffc0000000000 RSI: 0000000000000008 RDI: ffff88805c417098
RBP: ffff8880354077b0 R08: dffffc0000000000 R09: ffffed100b975718
R10: 0000000000000001 R11: ffffffff949ea4a3 R12: 1ffff1100b975746
R13: dffffc0000000000 R14: ffff88805cba4588 R15: dffffc0000000000
FS: 0000794a78e91b80(0000) GS:ffff888068d00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007bd5283ccf58 CR3: 000000004b7aa000 CR4: 00000000001006e0
Call Trace:
? dpm_complete+0x67b/0x67b
? i915_gem_suspend+0x14d/0x1ad
sst_soc_prepare+0x91/0x1dd
? sst_be_hw_params+0x7e/0x7e
dpm_prepare+0x39a/0x88b
dpm_suspend_start+0x13/0x9d
suspend_devices_and_enter+0x18f/0xbd7
? arch_suspend_enable_irqs+0x11/0x11
? printk+0xd9/0x12d
? lock_release+0x95f/0x95f
? log_buf_vmcoreinfo_setup+0x131/0x131
? rcu_read_lock_sched_held+0x140/0x22a
? __bpf_trace_rcu_utilization+0xa/0xa
? __pm_pr_dbg+0x186/0x190
? pm_notifier_call_chain+0x39/0x39
? suspend_test+0x9d/0x9d
pm_suspend+0x2f4/0x728
? trace_suspend_resume+0x3da/0x3da
? lock_release+0x95f/0x95f
? kernfs_fop_write+0x19f/0x32d
state_store+0xd8/0x147
? sysfs_kf_read+0x155/0x155
kernfs_fop_write+0x23e/0x32d
__vfs_write+0x108/0x608
? vfs_read+0x2e9/0x2e9
? rcu_read_lock_sched_held+0x140/0x22a
? __bpf_trace_rcu_utilization+0xa/0xa
? debug_smp_processor_id+0x10/0x10
? selinux_file_permission+0x1c5/0x3c8
? rcu_sync_lockdep_assert+0x6a/0xad
? __sb_start_write+0x129/0x2ac
vfs_write+0x1aa/0x434
ksys_write+0xfe/0x1be
? __ia32_sys_read+0x82/0x82
do_syscall_64+0xcd/0x120
entry_SYSCALL_64_after_hwframe+0x49/0xbe
In the observed situation, the problem is seen because the codec driver
failed to probe due to a hardware problem.
max98090 i2c-193C9890:00: Failed to read device revision: -1
max98090 i2c-193C9890:00: ASoC: failed to probe component -1
cht-bsw-max98090 cht-bsw-max98090: ASoC: failed to instantiate card -1
cht-bsw-max98090 cht-bsw-max98090: snd_soc_register_card failed -1
cht-bsw-max98090: probe of cht-bsw-max98090 failed with error -1
The problem is similar to the problem solved with commit 2fc995a87f2e
("ASoC: intel: Fix crash at suspend/resume without card registration"),
but codec registration fails at a later point. At that time, the pointer
checked with the above mentioned commit is already set, but it is not
cleared if the device is subsequently removed. Adding a remove function
to clear the pointer fixes the problem.
Cc: stable@vger.kernel.org
Cc: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Cc: Curtis Malainey <cujomalainey@chromium.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit a0c426fe143328760c9fd565cd203a37a7b4fde8 ]
We will get DAI ID from "reg" property if it has on DT, otherwise get
it by counting port/endpoint.
But in below case, we need to get DAI ID = 0 via port reg = <0>, but
current implementation returns ID = 1, because it can't judge ID = 0 was
from "non reg" or "reg = <0>".
Thus, it will count port/endpoint number as "non reg" case.
of_graph_parse_endpoint() implementation itself is not a problem,
but because asoc_simple_card_get_dai_id() need to count port/endpoint
number when "non reg" case, it need to know ID = 0 was from
"non reg" or "reg = <0>".
This patch fix this issue.
port {
reg = <0>;
xxxx: endpoint@0 {
};
=> xxxx: endpoint@1 {
};
};
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 11907e9d3533648615db08140e3045b829d2c141 ]
The of_find_device_by_node() takes a reference to the underlying device
structure, we should release that reference.
Signed-off-by: Wen Yang <yellowriver2010@hotmil.com>
Cc: Timur Tabi <timur@kernel.org>
Cc: Nicolin Chen <nicoleotsuka@gmail.com>
Cc: Xiubo Li <Xiubo.Lee@gmail.com>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.com>
Cc: alsa-devel@alsa-project.org
Cc: linuxppc-dev@lists.ozlabs.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 8fa857da9744f513036df1c43ab57f338941ae7d ]
The of_find_device_by_node() takes a reference to the underlying device
structure, we should release that reference.
Detected by coccinelle with the following warnings:
./sound/soc/fsl/imx-sgtl5000.c:169:1-7: ERROR: missing put_device;
call of_find_device_by_node on line 105, but without a corresponding
object release within this function.
./sound/soc/fsl/imx-sgtl5000.c:177:1-7: ERROR: missing put_device;
call of_find_device_by_node on line 105, but without a corresponding
object release within this function.
Signed-off-by: Wen Yang <yellowriver2010@hotmail.com>
Cc: Timur Tabi <timur@kernel.org>
Cc: Nicolin Chen <nicoleotsuka@gmail.com>
Cc: Xiubo Li <Xiubo.Lee@gmail.com>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Pengutronix Kernel Team <kernel@pengutronix.de>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: alsa-devel@alsa-project.org
Cc: linuxppc-dev@lists.ozlabs.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
