/* * Copyright (C) 2016 Texas Instruments Incorporated - http://www.ti.com/ * * This program is free software; you can redistribute it and/or modify * it under the terms of the GNU General Public License version 2 as * published by the Free Software Foundation. */ #include "dra72-evm-common.dtsi" #include "dra72x-mmc-iodelay.dtsi" #include / { model = "TI DRA722 Rev C EVM"; memory@0 { device_type = "memory"; reg = <0x0 0x80000000 0x0 0x80000000>; /* 2GB */ }; evm_1v8_sw: fixedregulator-evm_1v8 { compatible = "regulator-fixed"; regulator-name = "evm_1v8"; regulator-min-microvolt = <1800000>; regulator-max-microvolt = <1800000>; vin-supply = <&smps4_reg>; regulator-always-on; regulator-boot-on; }; }; &i2c1 { tps65917: tps65917@58 { reg = <0x58>; interrupts = ; /* IRQ_SYS_1N */ }; }; #include "dra72-evm-tps65917.dtsi" &ldo2_reg { /* LDO2_OUT --> VDDA_1V8_PHY2 */ regulator-always-on; regulator-boot-on; }; &hdmi { vdda-supply = <&ldo2_reg>; }; &pcf_gpio_21 { interrupt-parent = <&gpio3>; interrupts = <30 IRQ_TYPE_EDGE_FALLING>; }; &mac { mode-gpios = <&pcf_gpio_21 4 GPIO_ACTIVE_LOW>, <&pcf_hdmi 9 GPIO_ACTIVE_LOW>, /* P11 */ <&pcf_hdmi 10 GPIO_ACTIVE_LOW>; /* P12 */ dual_emac; }; &cpsw_emac0 { phy_id = <&davinci_mdio>, <2>; phy-mode = "rgmii-id"; dual_emac_res_vlan = <1>; }; &cpsw_emac1 { phy_id = <&davinci_mdio>, <3>; phy-mode = "rgmii-id"; dual_emac_res_vlan = <2>; }; &davinci_mdio { dp83867_0: ethernet-phy@2 { reg = <2>; ti,rx-internal-delay = ; ti,tx-internal-delay = ; ti,fifo-depth = ; ti,min-output-impedance; interrupt-parent = <&gpio6>; interrupts = <16 IRQ_TYPE_EDGE_FALLING>; ti,dp83867-rxctrl-strap-quirk; }; dp83867_1: ethernet-phy@3 { reg = <3>; ti,rx-internal-delay = ; ti,tx-internal-delay = ; ti,fifo-depth = ; ti,min-output-impedance; interrupt-parent = <&gpio6>; interrupts = <16 IRQ_TYPE_EDGE_FALLING>; ti,dp83867-rxctrl-strap-quirk; }; }; &mmc1 { pinctrl-names = "default", "hs", "sdr12", "sdr25", "sdr50", "ddr50", "sdr104"; pinctrl-0 = <&mmc1_pins_default>; pinctrl-1 = <&mmc1_pins_hs>; pinctrl-2 = <&mmc1_pins_sdr12>; pinctrl-3 = <&mmc1_pins_sdr25>; pinctrl-4 = <&mmc1_pins_sdr50>; pinctrl-5 = <&mmc1_pins_ddr50_rev20 &mmc1_iodelay_ddr50_conf>; pinctrl-6 = <&mmc1_pins_sdr104 &mmc1_iodelay_sdr104_rev20_conf>; vqmmc-supply = <&ldo1_reg>; }; &mmc2 { pinctrl-names = "default", "hs", "ddr_1_8v", "hs200_1_8v"; pinctrl-0 = <&mmc2_pins_default>; pinctrl-1 = <&mmc2_pins_hs>; pinctrl-2 = <&mmc2_pins_ddr_rev20 &mmc2_iodelay_ddr_conf>; pinctrl-3 = <&mmc2_pins_hs200 &mmc2_iodelay_hs200_rev20_conf>; vmmc-supply = <&evm_1v8_sw>; };