armv8: ls1046ardb: Add LS1046ARDB board support

LS1046ARDB Specification:
-------------------------
Memory subsystem:
 * 8GByte DDR4 SDRAM (64bit bus)
 * 512 Mbyte NAND flash
 * Two 64 Mbyte high-speed SPI flash
 * SD connector to interface with the SD memory card
 * On-board 4G eMMC

Ethernet:
 * Two XFI 10G ports
 * Two SGMII ports
 * Two RGMII ports

PCIe:
 * PCIe1 (SerDes2 Lane0) to miniPCIe slot
 * PCIe2 (SerDes2 Lane1) to x2 PCIe slot
 * PCIe3 (SerDes2 Lane2) to x4 PCIe slot

SATA:
 * SerDes2 Lane3 to SATA port

USB 3.0: one super speed USB 3.0 type A port
	 one Micro-AB port

UART: supports two UARTs up to 115200 bps for console

Signed-off-by: Mingkai Hu <mingkai.hu@nxp.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@nxp.com>
Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>

13 files changed, 751 insertions, 0 deletions

diff --git a/board/freescale/ls1046ardb/Kconfig b/board/freescale/ls1046ardb/Kconfig
new file mode 100644
index 0000000000..a62255c78d
--- /dev/null
+++ b/board/freescale/ls1046ardb/Kconfig
@@ -0,0 +1,16 @@
+
+if TARGET_LS1046ARDB
+
+config SYS_BOARD
+	default "ls1046ardb"
+
+config SYS_VENDOR
+	default "freescale"
+
+config SYS_SOC
+	default "fsl-layerscape"
+
+config SYS_CONFIG_NAME
+	default "ls1046ardb"
+
+endif
diff --git a/board/freescale/ls1046ardb/MAINTAINERS b/board/freescale/ls1046ardb/MAINTAINERS
new file mode 100644
index 0000000000..ff42bef090
--- /dev/null
+++ b/board/freescale/ls1046ardb/MAINTAINERS
@@ -0,0 +1,9 @@
+LS1046A BOARD
+M:	Mingkai Hu <mingkai.hu@nxp.com>
+S:	Maintained
+F:	board/freescale/ls1046ardb/
+F:	board/freescale/ls1046ardb/ls1046ardb.c
+F:	include/configs/ls1046ardb.h
+F:	configs/ls1046ardb_qspi_defconfig
+F:	configs/ls1046ardb_sdcard_defconfig
+F:	configs/ls1046ardb_emmc_defconfig
diff --git a/board/freescale/ls1046ardb/Makefile b/board/freescale/ls1046ardb/Makefile
new file mode 100644
index 0000000000..348eb76ea7
--- /dev/null
+++ b/board/freescale/ls1046ardb/Makefile
@@ -0,0 +1,10 @@
+#
+# Copyright 2016 Freescale Semiconductor
+#
+# SPDX-License-Identifier:	GPL-2.0+
+#
+
+obj-y += cpld.o
+obj-y += ddr.o
+obj-y += ls1046ardb.o
+obj-$(CONFIG_SYS_DPAA_FMAN) += eth.o
diff --git a/board/freescale/ls1046ardb/README b/board/freescale/ls1046ardb/README
new file mode 100644
index 0000000000..1ef7d479a3
--- /dev/null
+++ b/board/freescale/ls1046ardb/README
@@ -0,0 +1,76 @@
+Overview
+--------
+The LS1046A Reference Design Board (RDB) is a high-performance computing,
+evaluation, and development platform that supports the QorIQ LS1046A
+LayerScape Architecture processor. The LS1046ARDB provides SW development
+platform for the Freescale LS1046A processor series, with a complete
+debugging environment. The LS1046A RDB is lead-free and RoHS-compliant.
+
+LS1046A SoC Overview
+--------------------
+Please refer arch/arm/cpu/armv8/fsl-layerscape/doc/README.soc for LS1046A
+SoC overview.
+
+ LS1046ARDB board Overview
+ -----------------------
+ - SERDES1 Connections, 4 lanes supporting:
+      - Lane0: XFI with x1 RJ45 connector
+      - Lane1: XFI Cage
+      - Lane2: SGMII.5
+      - Lane3: SGMII.6
+ - SERDES2 Connections, 4 lanes supporting:
+      - Lane0: PCIe1 with miniPCIe slot
+      - Lane1: PCIe2 with PCIe x2 slot
+      - Lane2: PCIe3 with PCIe x4 slot
+      - Lane3: SATA
+ - DDR Controller
+     - 8GB 64bits DDR4 SDRAM. Support rates of up to 2133MT/s
+ -IFC/Local Bus
+    - One 512 MB NAND flash with ECC support
+    - CPLD connection
+ - USB 3.0
+    - one Type A port, one Micro-AB port
+ - SDHC: connects directly to a full SD/MMC slot
+ - DSPI: 64 MB high-speed flash Memory for boot code and storage (up to 108MHz)
+ - 4 I2C controllers
+ - UART
+   - Two 4-pin serial ports at up to 115.2 Kbit/s
+   - Two DB9 D-Type connectors supporting one Serial port each
+ - ARM JTAG support
+
+Memory map from core's view
+----------------------------
+Start Address	 End Address	 Description		Size
+0x00_0000_0000 - 0x00_000F_FFFF  Secure Boot ROM	1MB
+0x00_0100_0000 - 0x00_0FFF_FFFF  CCSRBAR		240MB
+0x00_1000_0000 - 0x00_1000_FFFF  OCRAM0 		64KB
+0x00_1001_0000 - 0x00_1001_FFFF  OCRAM1 		64KB
+0x00_2000_0000 - 0x00_20FF_FFFF  DCSR			16MB
+0x00_7E80_0000 - 0x00_7E80_FFFF  IFC - NAND Flash	64KB
+0x00_7FB0_0000 - 0x00_7FB0_0FFF  IFC - CPLD		4KB
+0x00_8000_0000 - 0x00_FFFF_FFFF  DRAM1			2GB
+0x05_0000_0000 - 0x05_07FF_FFFF  QMAN S/W Portal	128M
+0x05_0800_0000 - 0x05_0FFF_FFFF  BMAN S/W Portal	128M
+0x08_8000_0000 - 0x09_FFFF_FFFF  DRAM2			6GB
+0x40_0000_0000 - 0x47_FFFF_FFFF  PCI Express1		32G
+0x48_0000_0000 - 0x4F_FFFF_FFFF  PCI Express2		32G
+0x50_0000_0000 - 0x57_FFFF_FFFF  PCI Express3		32G
+
+QSPI flash map:
+Start Address    End Address     Description		Size
+0x00_4000_0000 - 0x00_400F_FFFF  RCW + PBI		1MB
+0x00_4010_0000 - 0x00_401F_FFFF  U-Boot 		1MB
+0x00_4020_0000 - 0x00_402F_FFFF  U-Boot Env		1MB
+0x00_4030_0000 - 0x00_403F_FFFF  FMan ucode		1MB
+0x00_4040_0000 - 0x00_404F_FFFF  UEFI			1MB
+0x00_4050_0000 - 0x00_406F_FFFF  PPA			2MB
+0x00_4070_0000 - 0x00_408F_FFFF  Secure boot header
+			         + bootscript		2MB
+0x00_4090_0000 - 0x00_40FF_FFFF  Reserved		7MB
+0x00_4100_0000 - 0x00_43FF_FFFF  FIT Image		48MB
+
+Booting Options
+---------------
+a) QSPI boot
+b) SD boot
+c) eMMC boot
diff --git a/board/freescale/ls1046ardb/cpld.c b/board/freescale/ls1046ardb/cpld.c
new file mode 100644
index 0000000000..81a646e28c
--- /dev/null
+++ b/board/freescale/ls1046ardb/cpld.c
@@ -0,0 +1,158 @@
+/*
+ * Copyright 2016 Freescale Semiconductor
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ *
+ * Freescale LS1046ARDB board-specific CPLD controlling supports.
+ */
+
+#include <common.h>
+#include <command.h>
+#include <asm/io.h>
+#include "cpld.h"
+
+u8 cpld_read(unsigned int reg)
+{
+	void *p = (void *)CONFIG_SYS_CPLD_BASE;
+
+	return in_8(p + reg);
+}
+
+void cpld_write(unsigned int reg, u8 value)
+{
+	void *p = (void *)CONFIG_SYS_CPLD_BASE;
+
+	out_8(p + reg, value);
+}
+
+/* Set the boot bank to the alternate bank */
+void cpld_set_altbank(void)
+{
+	u16 reg = CPLD_CFG_RCW_SRC_QSPI;
+	u8 reg4 = CPLD_READ(soft_mux_on);
+	u8 reg5 = (u8)(reg >> 1);
+	u8 reg6 = (u8)(reg & 1);
+	u8 reg7 = CPLD_READ(vbank);
+
+	cpld_rev_bit(&reg5);
+
+	CPLD_WRITE(soft_mux_on, reg4 | CPLD_SW_MUX_BANK_SEL | 1);
+
+	CPLD_WRITE(cfg_rcw_src1, reg5);
+	CPLD_WRITE(cfg_rcw_src2, reg6);
+
+	reg7 = (reg7 & ~CPLD_BANK_SEL_MASK) | CPLD_BANK_SEL_ALTBANK;
+	CPLD_WRITE(vbank, reg7);
+
+	CPLD_WRITE(system_rst, 1);
+}
+
+/* Set the boot bank to the default bank */
+void cpld_set_defbank(void)
+{
+	u16 reg = CPLD_CFG_RCW_SRC_QSPI;
+	u8 reg4 = CPLD_READ(soft_mux_on);
+	u8 reg5 = (u8)(reg >> 1);
+	u8 reg6 = (u8)(reg & 1);
+
+	cpld_rev_bit(&reg5);
+
+	CPLD_WRITE(soft_mux_on, reg4 | CPLD_SW_MUX_BANK_SEL | 1);
+
+	CPLD_WRITE(cfg_rcw_src1, reg5);
+	CPLD_WRITE(cfg_rcw_src2, reg6);
+
+	CPLD_WRITE(vbank, 0);
+
+	CPLD_WRITE(system_rst, 1);
+}
+
+void cpld_set_sd(void)
+{
+	u16 reg = CPLD_CFG_RCW_SRC_SD;
+	u8 reg5 = (u8)(reg >> 1);
+	u8 reg6 = (u8)(reg & 1);
+
+	cpld_rev_bit(&reg5);
+
+	CPLD_WRITE(soft_mux_on, 1);
+
+	CPLD_WRITE(cfg_rcw_src1, reg5);
+	CPLD_WRITE(cfg_rcw_src2, reg6);
+
+	CPLD_WRITE(system_rst, 1);
+}
+#ifdef DEBUG
+static void cpld_dump_regs(void)
+{
+	printf("cpld_ver	= %x\n", CPLD_READ(cpld_ver));
+	printf("cpld_ver_sub	= %x\n", CPLD_READ(cpld_ver_sub));
+	printf("pcba_ver	= %x\n", CPLD_READ(pcba_ver));
+	printf("soft_mux_on	= %x\n", CPLD_READ(soft_mux_on));
+	printf("cfg_rcw_src1	= %x\n", CPLD_READ(cfg_rcw_src1));
+	printf("cfg_rcw_src2	= %x\n", CPLD_READ(cfg_rcw_src2));
+	printf("vbank		= %x\n", CPLD_READ(vbank));
+	printf("sysclk_sel	= %x\n", CPLD_READ(sysclk_sel));
+	printf("uart_sel	= %x\n", CPLD_READ(uart_sel));
+	printf("sd1refclk_sel	= %x\n", CPLD_READ(sd1refclk_sel));
+	printf("rgmii_1588_sel	= %x\n", CPLD_READ(rgmii_1588_sel));
+	printf("1588_clk_sel	= %x\n", CPLD_READ(reg_1588_clk_sel));
+	printf("status_led	= %x\n", CPLD_READ(status_led));
+	printf("sd_emmc		= %x\n", CPLD_READ(sd_emmc));
+	printf("vdd_en		= %x\n", CPLD_READ(vdd_en));
+	printf("vdd_sel		= %x\n", CPLD_READ(vdd_sel));
+	putc('\n');
+}
+#endif
+
+void cpld_rev_bit(unsigned char *value)
+{
+	u8 rev_val, val;
+	int i;
+
+	val = *value;
+	rev_val = val & 1;
+	for (i = 1; i <= 7; i++) {
+		val >>= 1;
+		rev_val <<= 1;
+		rev_val |= val & 1;
+	}
+
+	*value = rev_val;
+}
+
+int do_cpld(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
+{
+	int rc = 0;
+
+	if (argc <= 1)
+		return cmd_usage(cmdtp);
+
+	if (strcmp(argv[1], "reset") == 0) {
+		if (strcmp(argv[2], "altbank") == 0)
+			cpld_set_altbank();
+		else if (strcmp(argv[2], "sd") == 0)
+			cpld_set_sd();
+		else
+			cpld_set_defbank();
+#ifdef DEBUG
+	} else if (strcmp(argv[1], "dump") == 0) {
+		cpld_dump_regs();
+#endif
+	} else {
+		rc = cmd_usage(cmdtp);
+	}
+
+	return rc;
+}
+
+U_BOOT_CMD(
+	cpld, CONFIG_SYS_MAXARGS, 1, do_cpld,
+	"Reset the board or alternate bank",
+	"reset: reset to default bank\n"
+	"cpld reset altbank: reset to alternate bank\n"
+	"cpld reset sd: reset to boot from SD card\n"
+#ifdef DEBUG
+	"cpld dump - display the CPLD registers\n"
+#endif
+);
diff --git a/board/freescale/ls1046ardb/cpld.h b/board/freescale/ls1046ardb/cpld.h
new file mode 100644
index 0000000000..458da7e892
--- /dev/null
+++ b/board/freescale/ls1046ardb/cpld.h
@@ -0,0 +1,49 @@
+/*
+ * Copyright 2016 Freescale Semiconductor
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#ifndef __CPLD_H__
+#define __CPLD_H__
+
+/*
+ * CPLD register set of LS1046ARDB board-specific.
+ * CPLD Revision:  V2.1
+ */
+struct cpld_data {
+	u8 cpld_ver;		/* 0x0 - CPLD Major Revision Register */
+	u8 cpld_ver_sub;	/* 0x1 - CPLD Minor Revision Register */
+	u8 pcba_ver;		/* 0x2 - PCBA Revision Register */
+	u8 system_rst;		/* 0x3 - system reset register */
+	u8 soft_mux_on;		/* 0x4 - Switch Control Enable Register */
+	u8 cfg_rcw_src1;	/* 0x5 - RCW Source Location POR Regsiter 1 */
+	u8 cfg_rcw_src2;	/* 0x6 - RCW Source Location POR Regsiter 2 */
+	u8 vbank;		/* 0x7 - QSPI Flash Bank Setting Register */
+	u8 sysclk_sel;		/* 0x8 - System clock POR Register */
+	u8 uart_sel;		/* 0x9 - UART1 Connection Control Register */
+	u8 sd1refclk_sel;	/* 0xA - */
+	u8 rgmii_1588_sel;	/* 0xB - */
+	u8 reg_1588_clk_sel;	/* 0xC - */
+	u8 status_led;		/* 0xD - */
+	u8 global_rst;		/* 0xE - */
+	u8 sd_emmc;             /* 0xF - SD/EMMC Interface Control Regsiter */
+	u8 vdd_en;              /* 0x10 - VDD Voltage Control Enable Register */
+	u8 vdd_sel;             /* 0x11 - VDD Voltage Control Register */
+};
+
+u8 cpld_read(unsigned int reg);
+void cpld_write(unsigned int reg, u8 value);
+void cpld_rev_bit(unsigned char *value);
+
+#define CPLD_READ(reg) cpld_read(offsetof(struct cpld_data, reg))
+#define CPLD_WRITE(reg, value)  \
+	cpld_write(offsetof(struct cpld_data, reg), value)
+
+/* CPLD on IFC */
+#define CPLD_SW_MUX_BANK_SEL	0x40
+#define CPLD_BANK_SEL_MASK	0x07
+#define CPLD_BANK_SEL_ALTBANK	0x04
+#define CPLD_CFG_RCW_SRC_QSPI	0x044
+#define CPLD_CFG_RCW_SRC_SD	0x040
+#endif
diff --git a/board/freescale/ls1046ardb/ddr.c b/board/freescale/ls1046ardb/ddr.c
new file mode 100644
index 0000000000..a9b7dbdf90
--- /dev/null
+++ b/board/freescale/ls1046ardb/ddr.c
@@ -0,0 +1,140 @@
+/*
+ * Copyright 2016 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <common.h>
+#include <fsl_ddr_sdram.h>
+#include <fsl_ddr_dimm_params.h>
+#include "ddr.h"
+#ifdef CONFIG_FSL_DEEP_SLEEP
+#include <fsl_sleep.h>
+#endif
+
+DECLARE_GLOBAL_DATA_PTR;
+
+void fsl_ddr_board_options(memctl_options_t *popts,
+			   dimm_params_t *pdimm,
+			   unsigned int ctrl_num)
+{
+	const struct board_specific_parameters *pbsp, *pbsp_highest = NULL;
+	ulong ddr_freq;
+
+	if (ctrl_num > 1) {
+		printf("Not supported controller number %d\n", ctrl_num);
+		return;
+	}
+	if (!pdimm->n_ranks)
+		return;
+
+	pbsp = udimms[0];
+
+	/* Get clk_adjust, wrlvl_start, wrlvl_ctl, according to the board ddr
+	 * freqency and n_banks specified in board_specific_parameters table.
+	 */
+	ddr_freq = get_ddr_freq(0) / 1000000;
+	while (pbsp->datarate_mhz_high) {
+		if (pbsp->n_ranks == pdimm->n_ranks) {
+			if (ddr_freq <= pbsp->datarate_mhz_high) {
+				popts->clk_adjust = pbsp->clk_adjust;
+				popts->wrlvl_start = pbsp->wrlvl_start;
+				popts->wrlvl_ctl_2 = pbsp->wrlvl_ctl_2;
+				popts->wrlvl_ctl_3 = pbsp->wrlvl_ctl_3;
+				goto found;
+			}
+			pbsp_highest = pbsp;
+		}
+		pbsp++;
+	}
+
+	if (pbsp_highest) {
+		printf("Error: board specific timing not found for %lu MT/s\n",
+		       ddr_freq);
+		printf("Trying to use the highest speed (%u) parameters\n",
+		       pbsp_highest->datarate_mhz_high);
+		popts->clk_adjust = pbsp_highest->clk_adjust;
+		popts->wrlvl_start = pbsp_highest->wrlvl_start;
+		popts->wrlvl_ctl_2 = pbsp->wrlvl_ctl_2;
+		popts->wrlvl_ctl_3 = pbsp->wrlvl_ctl_3;
+	} else {
+		panic("DIMM is not supported by this board");
+	}
+found:
+	debug("Found timing match: n_ranks %d, data rate %d, rank_gb %d\n",
+	      pbsp->n_ranks, pbsp->datarate_mhz_high, pbsp->rank_gb);
+
+	popts->data_bus_width = 0;	/* 64-bit data bus */
+	popts->otf_burst_chop_en = 0;
+	popts->burst_length = DDR_BL8;
+	popts->bstopre = 0;		/* enable auto precharge */
+
+	/*
+	 * Factors to consider for half-strength driver enable:
+	 *	- number of DIMMs installed
+	 */
+	popts->half_strength_driver_enable = 0;
+	/*
+	 * Write leveling override
+	 */
+	popts->wrlvl_override = 1;
+	popts->wrlvl_sample = 0xf;
+
+	/*
+	 * Rtt and Rtt_WR override
+	 */
+	popts->rtt_override = 0;
+
+	/* Enable ZQ calibration */
+	popts->zq_en = 1;
+
+	popts->ddr_cdr1 = DDR_CDR1_DHC_EN | DDR_CDR1_ODT(DDR_CDR_ODT_80ohm);
+	popts->ddr_cdr2 = DDR_CDR2_ODT(DDR_CDR_ODT_80ohm) |
+			  DDR_CDR2_VREF_TRAIN_EN | DDR_CDR2_VREF_RANGE_2;
+}
+
+phys_size_t initdram(int board_type)
+{
+	phys_size_t dram_size;
+
+#if defined(CONFIG_SPL) && !defined(CONFIG_SPL_BUILD)
+	return fsl_ddr_sdram_size();
+#else
+	puts("Initializing DDR....using SPD\n");
+
+	dram_size = fsl_ddr_sdram();
+#endif
+
+	erratum_a008850_post();
+
+	return dram_size;
+}
+
+void dram_init_banksize(void)
+{
+	/*
+	 * gd->arch.secure_ram tracks the location of secure memory.
+	 * It was set as if the memory starts from 0.
+	 * The address needs to add the offset of its bank.
+	 */
+	gd->bd->bi_dram[0].start = CONFIG_SYS_SDRAM_BASE;
+	if (gd->ram_size > CONFIG_SYS_DDR_BLOCK1_SIZE) {
+		gd->bd->bi_dram[0].size = CONFIG_SYS_DDR_BLOCK1_SIZE;
+		gd->bd->bi_dram[1].start = CONFIG_SYS_DDR_BLOCK2_BASE;
+		gd->bd->bi_dram[1].size = gd->ram_size -
+					  CONFIG_SYS_DDR_BLOCK1_SIZE;
+#ifdef CONFIG_SYS_MEM_RESERVE_SECURE
+		gd->arch.secure_ram = gd->bd->bi_dram[1].start +
+				 gd->arch.secure_ram -
+				 CONFIG_SYS_DDR_BLOCK1_SIZE;
+		gd->arch.secure_ram |= MEM_RESERVE_SECURE_MAINTAINED;
+#endif
+	} else {
+		gd->bd->bi_dram[0].size = gd->ram_size;
+#ifdef CONFIG_SYS_MEM_RESERVE_SECURE
+		gd->arch.secure_ram = gd->bd->bi_dram[0].start +
+				 gd->arch.secure_ram;
+		gd->arch.secure_ram |= MEM_RESERVE_SECURE_MAINTAINED;
+#endif
+	}
+}
diff --git a/board/freescale/ls1046ardb/ddr.h b/board/freescale/ls1046ardb/ddr.h
new file mode 100644
index 0000000000..9e440f67b4
--- /dev/null
+++ b/board/freescale/ls1046ardb/ddr.h
@@ -0,0 +1,44 @@
+/*
+ * Copyright 2016 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#ifndef __DDR_H__
+#define __DDR_H__
+
+void erratum_a008850_post(void);
+
+struct board_specific_parameters {
+	u32 n_ranks;
+	u32 datarate_mhz_high;
+	u32 rank_gb;
+	u32 clk_adjust;
+	u32 wrlvl_start;
+	u32 wrlvl_ctl_2;
+	u32 wrlvl_ctl_3;
+};
+
+/*
+ * These tables contain all valid speeds we want to override with board
+ * specific parameters. datarate_mhz_high values need to be in ascending order
+ * for each n_ranks group.
+ */
+static const struct board_specific_parameters udimm0[] = {
+	/*
+	 * memory controller 0
+	 *   num|  hi| rank|  clk| wrlvl |   wrlvl   |  wrlvl
+	 * ranks| mhz| GB  |adjst| start |   ctl2    |  ctl3
+	 */
+	{2,  1350, 0, 8,     6, 0x0708090B, 0x0C0D0E09,},
+	{2,  1666, 0, 8,     7, 0x08090A0C, 0x0D0F100B,},
+	{2,  1900, 0, 8,     7, 0x09090B0D, 0x0E10120B,},
+	{2,  2300, 0, 8,     9, 0x0A0B0C10, 0x1213140E,},
+	{}
+};
+
+static const struct board_specific_parameters *udimms[] = {
+	udimm0,
+};
+
+#endif
diff --git a/board/freescale/ls1046ardb/eth.c b/board/freescale/ls1046ardb/eth.c
new file mode 100644
index 0000000000..ac8bbec9a3
--- /dev/null
+++ b/board/freescale/ls1046ardb/eth.c
@@ -0,0 +1,77 @@
+/*
+ * Copyright 2016 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+#include <common.h>
+#include <asm/io.h>
+#include <netdev.h>
+#include <fm_eth.h>
+#include <fsl_dtsec.h>
+#include <fsl_mdio.h>
+#include <malloc.h>
+
+#include "../common/fman.h"
+
+int board_eth_init(bd_t *bis)
+{
+#ifdef CONFIG_FMAN_ENET
+	int i;
+	struct memac_mdio_info dtsec_mdio_info;
+	struct memac_mdio_info tgec_mdio_info;
+	struct mii_dev *dev;
+	u32 srds_s1;
+	struct ccsr_gur *gur = (void *)(CONFIG_SYS_FSL_GUTS_ADDR);
+
+	srds_s1 = in_be32(&gur->rcwsr[4]) &
+			FSL_CHASSIS2_RCWSR4_SRDS1_PRTCL_MASK;
+	srds_s1 >>= FSL_CHASSIS2_RCWSR4_SRDS1_PRTCL_SHIFT;
+
+	dtsec_mdio_info.regs =
+		(struct memac_mdio_controller *)CONFIG_SYS_FM1_DTSEC_MDIO_ADDR;
+
+	dtsec_mdio_info.name = DEFAULT_FM_MDIO_NAME;
+
+	/* Register the 1G MDIO bus */
+	fm_memac_mdio_init(bis, &dtsec_mdio_info);
+
+	tgec_mdio_info.regs =
+		(struct memac_mdio_controller *)CONFIG_SYS_FM1_TGEC_MDIO_ADDR;
+	tgec_mdio_info.name = DEFAULT_FM_TGEC_MDIO_NAME;
+
+	/* Register the 10G MDIO bus */
+	fm_memac_mdio_init(bis, &tgec_mdio_info);
+
+	/* Set the two on-board RGMII PHY address */
+	fm_info_set_phy_address(FM1_DTSEC3, RGMII_PHY1_ADDR);
+	fm_info_set_phy_address(FM1_DTSEC4, RGMII_PHY2_ADDR);
+
+	/* Set the two on-board SGMII PHY address */
+	fm_info_set_phy_address(FM1_DTSEC5, SGMII_PHY1_ADDR);
+	fm_info_set_phy_address(FM1_DTSEC6, SGMII_PHY2_ADDR);
+
+	/* Set the on-board AQ PHY address */
+	fm_info_set_phy_address(FM1_10GEC1, FM1_10GEC1_PHY_ADDR);
+
+	switch (srds_s1) {
+	case 0x1133:
+		break;
+	default:
+		printf("Invalid SerDes protocol 0x%x for LS1046ARDB\n",
+		       srds_s1);
+		break;
+	}
+
+	dev = miiphy_get_dev_by_name(DEFAULT_FM_MDIO_NAME);
+	for (i = FM1_DTSEC1; i < FM1_DTSEC1 + CONFIG_SYS_NUM_FM1_DTSEC; i++)
+		fm_info_set_mdio(i, dev);
+
+	/* XFI on lane A, MAC 9 */
+	dev = miiphy_get_dev_by_name(DEFAULT_FM_TGEC_MDIO_NAME);
+	fm_info_set_mdio(FM1_10GEC1, dev);
+
+	cpu_eth_init(bis);
+#endif
+
+	return pci_eth_init(bis);
+}
diff --git a/board/freescale/ls1046ardb/ls1046ardb.c b/board/freescale/ls1046ardb/ls1046ardb.c
new file mode 100644
index 0000000000..585c807818
--- /dev/null
+++ b/board/freescale/ls1046ardb/ls1046ardb.c
@@ -0,0 +1,136 @@
+/*
+ * Copyright 2016 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <common.h>
+#include <i2c.h>
+#include <fdt_support.h>
+#include <asm/io.h>
+#include <asm/arch/clock.h>
+#include <asm/arch/fsl_serdes.h>
+#include <asm/arch/ppa.h>
+#include <asm/arch/soc.h>
+#include <hwconfig.h>
+#include <ahci.h>
+#include <mmc.h>
+#include <scsi.h>
+#include <fm_eth.h>
+#include <fsl_csu.h>
+#include <fsl_esdhc.h>
+#include "cpld.h"
+
+DECLARE_GLOBAL_DATA_PTR;
+
+int checkboard(void)
+{
+	static const char *freq[2] = {"100.00MHZ", "156.25MHZ"};
+	u8 cfg_rcw_src1, cfg_rcw_src2;
+	u16 cfg_rcw_src;
+	u8 sd1refclk_sel;
+
+	puts("Board: LS1046ARDB, boot from ");
+
+	cfg_rcw_src1 = CPLD_READ(cfg_rcw_src1);
+	cfg_rcw_src2 = CPLD_READ(cfg_rcw_src2);
+	cpld_rev_bit(&cfg_rcw_src1);
+	cfg_rcw_src = cfg_rcw_src1;
+	cfg_rcw_src = (cfg_rcw_src << 1) | cfg_rcw_src2;
+
+	if (cfg_rcw_src == 0x44)
+		printf("QSPI vBank %d\n", CPLD_READ(vbank));
+	else if (cfg_rcw_src == 0x40)
+		puts("SD\n");
+	else
+		puts("Invalid setting of SW5\n");
+
+	printf("CPLD:  V%x.%x\nPCBA:  V%x.0\n", CPLD_READ(cpld_ver),
+	       CPLD_READ(cpld_ver_sub), CPLD_READ(pcba_ver));
+
+	puts("SERDES Reference Clocks:\n");
+	sd1refclk_sel = CPLD_READ(sd1refclk_sel);
+	printf("SD1_CLK1 = %s, SD1_CLK2 = %s\n", freq[sd1refclk_sel], freq[0]);
+
+	return 0;
+}
+
+int dram_init(void)
+{
+	gd->ram_size = initdram(0);
+
+	return 0;
+}
+
+int board_early_init_f(void)
+{
+	fsl_lsch2_early_init_f();
+
+	return 0;
+}
+
+int board_init(void)
+{
+	struct ccsr_scfg *scfg = (struct ccsr_scfg *)CONFIG_SYS_FSL_SCFG_ADDR;
+
+#ifdef CONFIG_LAYERSCAPE_NS_ACCESS
+	enable_layerscape_ns_access();
+#endif
+
+#ifdef CONFIG_FSL_LS_PPA
+	ppa_init();
+#endif
+
+	/* invert AQR105 IRQ pins polarity */
+	out_be32(&scfg->intpcr, AQR105_IRQ_MASK);
+
+	return 0;
+}
+
+void config_board_mux(void)
+{
+#ifdef CONFIG_HAS_FSL_XHCI_USB
+	struct ccsr_scfg *scfg = (struct ccsr_scfg *)CONFIG_SYS_FSL_SCFG_ADDR;
+	u32 usb_pwrfault;
+
+	/* USB3 is not used, configure mux to IIC4_SCL/IIC4_SDA */
+	out_be32(&scfg->rcwpmuxcr0, 0x3300);
+	out_be32(&scfg->usbdrvvbus_selcr, SCFG_USBDRVVBUS_SELCR_USB1);
+	usb_pwrfault = (SCFG_USBPWRFAULT_DEDICATED <<
+			SCFG_USBPWRFAULT_USB3_SHIFT) |
+			(SCFG_USBPWRFAULT_DEDICATED <<
+			SCFG_USBPWRFAULT_USB2_SHIFT) |
+			(SCFG_USBPWRFAULT_SHARED <<
+			SCFG_USBPWRFAULT_USB1_SHIFT);
+	out_be32(&scfg->usbpwrfault_selcr, usb_pwrfault);
+#endif
+}
+
+#ifdef CONFIG_MISC_INIT_R
+int misc_init_r(void)
+{
+	config_board_mux();
+	return 0;
+}
+#endif
+
+int ft_board_setup(void *blob, bd_t *bd)
+{
+	u64 base[CONFIG_NR_DRAM_BANKS];
+	u64 size[CONFIG_NR_DRAM_BANKS];
+
+	/* fixup DT for the two DDR banks */
+	base[0] = gd->bd->bi_dram[0].start;
+	size[0] = gd->bd->bi_dram[0].size;
+	base[1] = gd->bd->bi_dram[1].start;
+	size[1] = gd->bd->bi_dram[1].size;
+
+	fdt_fixup_memory_banks(blob, base, size, 2);
+	ft_cpu_setup(blob, bd);
+
+#ifdef CONFIG_SYS_DPAA_FMAN
+	fdt_fixup_fman_ethernet(blob);
+#endif
+
+	return 0;
+}
diff --git a/board/freescale/ls1046ardb/ls1046ardb_pbi.cfg b/board/freescale/ls1046ardb/ls1046ardb_pbi.cfg
new file mode 100644
index 0000000000..5478217524
--- /dev/null
+++ b/board/freescale/ls1046ardb/ls1046ardb_pbi.cfg
@@ -0,0 +1,22 @@
+#Configure Scratch register
+09570600 00000000
+09570604 10000000
+#Disable CCI barrier tranaction
+09570178 0000e010
+09180000 00000008
+#USB PHY frequency sel
+09570418 0000009e
+0957041c 0000009e
+09570420 0000009e
+#Serdes SATA
+09eb1300 80104e20
+09eb08dc 00502880
+#PEX gen3 link
+09570158 00000300
+89400890 01048000
+89500890 01048000
+89600890 01048000
+#Alt base register
+09570158 00001000
+#flush PBI data
+096100c0 000fffff
diff --git a/board/freescale/ls1046ardb/ls1046ardb_rcw_emmc.cfg b/board/freescale/ls1046ardb/ls1046ardb_rcw_emmc.cfg
new file mode 100644
index 0000000000..6a5076e099
--- /dev/null
+++ b/board/freescale/ls1046ardb/ls1046ardb_rcw_emmc.cfg
@@ -0,0 +1,7 @@
+#PBL preamble and RCW header
+aa55aa55 01ee0100
+# RCW
+0c150010 0e000000 00000000 00000000
+11335559 40000012 60040000 c1000000
+00000000 00000000 00000000 00238800
+20124000 00003000 00000096 00000001
diff --git a/board/freescale/ls1046ardb/ls1046ardb_rcw_sd.cfg b/board/freescale/ls1046ardb/ls1046ardb_rcw_sd.cfg
new file mode 100644
index 0000000000..d5265b846f
--- /dev/null
+++ b/board/freescale/ls1046ardb/ls1046ardb_rcw_sd.cfg
@@ -0,0 +1,7 @@
+#PBL preamble and RCW header
+aa55aa55 01ee0100
+# RCW
+0c150010 0e000000 00000000 00000000
+11335559 40005012 60040000 c1000000
+00000000 00000000 00000000 00238800
+20124000 00003101 00000096 00000001