board: apalis_imx6: Add KSZ9131 phy skew settings

This patch adds skew register settings for KSZ9131. It checks first
which phy is on the board and then applies the correct skew settings.

Skew settings calculation for the KSZ9131:
The i.MX6 SoC has an output skew tolerance of -100ps to 900ps. All
PCB traces where routed exactly the same length so we can calculate
the skew settings without taking the length into consideration. The
traces are all length matched.

RXC skew (PHY to MAC):
- We use the 2ns DLL controlled delay on the PHY
- We do not use the skew registers

This results in the following values:

		RXC
PHY fixed Delay	2000ps
PHY Added Delay	0ps
T_setup_R min	2.00ns
T_setup_R typ	2.00ns
T_setup_R max	2.00ns
T_hold_R min	1.60ns
T_hold_R typ	2.00ns
T_hold_R max	2.40ns

That means we are well within RGMII specs.

TXC skew (MAC to PHY):
- We use the 2ns DLL controlled delay on the PHY
- We then subtract ~0.6ns with TXD[0:3] and TXC clock pad skew
  register in a resulting ~1.4ns delay.

This results in the following values under consideration of the
tolerances:

		TXC min	TXC typ	TXC max
MAC min		-100ps	-100ps	-100ps
MAC max		900ps	900ps	900ps
PHY fixed Delay	2000ps	2000ps	2000ps
PHY added Delay	-340ps	-600ps	-859ps
T_setup_T min	1.56ns	1.30ns	1.04ns
T_setup_T typ	2.06ns	1.80ns	1.54ns
T_setup_T max	2.56ns	2.30ns	2.04ns
T_hold_T min	1.04ns	1.30ns	1.56ns
T_hold_T typ	1.94ns	2.20ns	2.46ns
T_hold_T max	2.84ns	3.10ns	3.36ns

This shows that T_hold_T min and T_setup_T min times are out of spec
for RGMII timing. However the KSZ9131 has a minimal value for this time
of 0.8ns which is met under all circumstances.

Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>

1 files changed, 73 insertions, 16 deletions

diff --git a/board/toradex/apalis_imx6/apalis_imx6.c b/board/toradex/apalis_imx6/apalis_imx6.c
index 3f85f1ac89..8c4a359c75 100644
--- a/board/toradex/apalis_imx6/apalis_imx6.c
+++ b/board/toradex/apalis_imx6/apalis_imx6.c
@@ -137,22 +137,79 @@ iomux_v3_cfg_t const usdhc3_pads[] = {
 
 int mx6_rgmii_rework(struct phy_device *phydev)
 {
-	/* control data pad skew - devaddr = 0x02, register = 0x04 */
-	ksz9031_phy_extended_write(phydev, 0x02,
-				   MII_KSZ9031_EXT_RGMII_CTRL_SIG_SKEW,
-				   MII_KSZ9031_MOD_DATA_NO_POST_INC, 0x0000);
-	/* rx data pad skew - devaddr = 0x02, register = 0x05 */
-	ksz9031_phy_extended_write(phydev, 0x02,
-				   MII_KSZ9031_EXT_RGMII_RX_DATA_SKEW,
-				   MII_KSZ9031_MOD_DATA_NO_POST_INC, 0x0000);
-	/* tx data pad skew - devaddr = 0x02, register = 0x05 */
-	ksz9031_phy_extended_write(phydev, 0x02,
-				   MII_KSZ9031_EXT_RGMII_TX_DATA_SKEW,
-				   MII_KSZ9031_MOD_DATA_NO_POST_INC, 0x0000);
-	/* gtx and rx clock pad skew - devaddr = 0x02, register = 0x08 */
-	ksz9031_phy_extended_write(phydev, 0x02,
-				   MII_KSZ9031_EXT_RGMII_CLOCK_SKEW,
-				   MII_KSZ9031_MOD_DATA_NO_POST_INC, 0x03FF);
+	int tmp;
+
+	switch (ksz9xx1_phy_get_id(phydev) & MII_KSZ9x31_SILICON_REV_MASK) {
+	case PHY_ID_KSZ9131:
+		/* read rxc dll control - devaddr = 0x02, register = 0x4c */
+		tmp = ksz9031_phy_extended_read(phydev, 0x02,
+					   MII_KSZ9131_EXT_RGMII_2NS_SKEW_RXDLL,
+					   MII_KSZ9031_MOD_DATA_NO_POST_INC);
+		/* disable rxdll bypass (enable 2ns skew delay on RXC) */
+		tmp &= ~MII_KSZ9131_RXTXDLL_BYPASS;
+		/* rxc data pad skew 2ns - devaddr = 0x02, register = 0x4c */
+		ksz9031_phy_extended_write(phydev, 0x02,
+					   MII_KSZ9131_EXT_RGMII_2NS_SKEW_RXDLL,
+					   MII_KSZ9031_MOD_DATA_NO_POST_INC,
+					   tmp);
+		/* read txc dll control - devaddr = 0x02, register = 0x4d */
+		tmp = ksz9031_phy_extended_read(phydev, 0x02,
+					   MII_KSZ9131_EXT_RGMII_2NS_SKEW_TXDLL,
+					   MII_KSZ9031_MOD_DATA_NO_POST_INC);
+		/* disable rxdll bypass (enable 2ns skew delay on TXC) */
+		tmp &= ~MII_KSZ9131_RXTXDLL_BYPASS;
+		/* txc data pad skew 2ns - devaddr = 0x02, register = 0x4d */
+		ksz9031_phy_extended_write(phydev, 0x02,
+					   MII_KSZ9131_EXT_RGMII_2NS_SKEW_TXDLL,
+					   MII_KSZ9031_MOD_DATA_NO_POST_INC,
+					   tmp);
+
+		/* control data pad skew - devaddr = 0x02, register = 0x04 */
+		ksz9031_phy_extended_write(phydev, 0x02,
+					   MII_KSZ9031_EXT_RGMII_CTRL_SIG_SKEW,
+					   MII_KSZ9031_MOD_DATA_NO_POST_INC,
+					   0x007d);
+		/* rx data pad skew - devaddr = 0x02, register = 0x05 */
+		ksz9031_phy_extended_write(phydev, 0x02,
+					   MII_KSZ9031_EXT_RGMII_RX_DATA_SKEW,
+					   MII_KSZ9031_MOD_DATA_NO_POST_INC,
+					   0x7777);
+		/* tx data pad skew - devaddr = 0x02, register = 0x05 */
+		ksz9031_phy_extended_write(phydev, 0x02,
+					   MII_KSZ9031_EXT_RGMII_TX_DATA_SKEW,
+					   MII_KSZ9031_MOD_DATA_NO_POST_INC,
+					   0xdddd);
+		/* gtx and rx clock pad skew - devaddr = 0x02,register = 0x08 */
+		ksz9031_phy_extended_write(phydev, 0x02,
+					   MII_KSZ9031_EXT_RGMII_CLOCK_SKEW,
+					   MII_KSZ9031_MOD_DATA_NO_POST_INC,
+					   0x0007);
+		break;
+	case PHY_ID_KSZ9031:
+	default:
+		/* control data pad skew - devaddr = 0x02, register = 0x04 */
+		ksz9031_phy_extended_write(phydev, 0x02,
+					   MII_KSZ9031_EXT_RGMII_CTRL_SIG_SKEW,
+					   MII_KSZ9031_MOD_DATA_NO_POST_INC,
+					   0x0000);
+		/* rx data pad skew - devaddr = 0x02, register = 0x05 */
+		ksz9031_phy_extended_write(phydev, 0x02,
+					   MII_KSZ9031_EXT_RGMII_RX_DATA_SKEW,
+					   MII_KSZ9031_MOD_DATA_NO_POST_INC,
+					   0x0000);
+		/* tx data pad skew - devaddr = 0x02, register = 0x05 */
+		ksz9031_phy_extended_write(phydev, 0x02,
+					   MII_KSZ9031_EXT_RGMII_TX_DATA_SKEW,
+					   MII_KSZ9031_MOD_DATA_NO_POST_INC,
+					   0x0000);
+		/* gtx and rx clock pad skew - devaddr = 0x02,register = 0x08 */
+		ksz9031_phy_extended_write(phydev, 0x02,
+					   MII_KSZ9031_EXT_RGMII_CLOCK_SKEW,
+					   MII_KSZ9031_MOD_DATA_NO_POST_INC,
+					   0x03FF);
+		break;
+	}
+
 	return 0;
 }