keymile: Factor out common includes again

Not that the Kconfig conversion of a lot of variables is done, we can
factor out the common include files for the keymile boards again (which
now contain hardly any #ifdef logic at all).

Signed-off-by: Mario Six <mario.six@gdsys.cc>

1 files changed, 2 insertions, 275 deletions

diff --git a/include/configs/kmsupx5.h b/include/configs/kmsupx5.h
index 0dd7420e8c..ba33e6074b 100644
--- a/include/configs/kmsupx5.h
+++ b/include/configs/kmsupx5.h
@@ -26,283 +26,10 @@
 #define CONFIG_KM_BOARD_NAME	"kmsupx5"
 #define CONFIG_HOSTNAME		"kmsupx5"
 
-/*
- * High Level Configuration Options
- */
-#define CONFIG_QE	/* Has QE */
-#define CONFIG_KM8321	/* Keymile PBEC8321 board specific */
-
-#define CONFIG_KM_DEF_ARCH	"arch=ppc_8xx\0"
-
 /* include common defines/options for all Keymile boards */
 #include "km/keymile-common.h"
 #include "km/km-powerpc.h"
-
-/*
- * System Clock Setup
- */
-#define CONFIG_83XX_CLKIN		66000000
-#define CONFIG_SYS_CLK_FREQ		66000000
-#define CONFIG_83XX_PCICLK		66000000
-
-/*
- * DDR Setup
- */
-#define CONFIG_SYS_SDRAM_BASE		0x00000000 /* DDR is system memory */
-#define CONFIG_SYS_SDRAM_BASE2	(CONFIG_SYS_SDRAM_BASE + 0x10000000) /* +256M */
-
-#define CONFIG_SYS_DDR_SDRAM_CLK_CNTL	(DDR_SDRAM_CLK_CNTL_SS_EN | \
-					DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05)
-
-#define CFG_83XX_DDR_USES_CS0
-
-/*
- * Manually set up DDR parameters
- */
-#define CONFIG_DDR_II
-#define CONFIG_SYS_DDR_SIZE		2048 /* MB */
-
-/*
- * The reserved memory
- */
-#define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_TEXT_BASE /* start of monitor */
-#define CONFIG_SYS_FLASH_BASE		0xF0000000
-
-#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
-#define CONFIG_SYS_RAMBOOT
-#endif
-
-/* Reserve 768 kB for Mon */
-#define CONFIG_SYS_MONITOR_LEN		(768 * 1024)
-
-/*
- * Initial RAM Base Address Setup
- */
-#define CONFIG_SYS_INIT_RAM_LOCK
-#define CONFIG_SYS_INIT_RAM_ADDR	0xE6000000 /* Initial RAM address */
-#define CONFIG_SYS_INIT_RAM_SIZE	0x1000 /* End of used area in RAM */
-#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - \
-						GENERATED_GBL_DATA_SIZE)
-
-/*
- * Init Local Bus Memory Controller:
- *
- * Bank Bus     Machine PortSz  Size  Device
- * ---- ---     ------- ------  -----  ------
- *  0   Local   GPCM    16 bit  256MB FLASH
- *  1   Local   GPCM     8 bit  128MB GPIO/PIGGY
- *
- */
-/*
- * FLASH on the Local Bus
- */
-#define CONFIG_SYS_FLASH_SIZE		256 /* max FLASH size is 256M */
-
-
-#define CONFIG_SYS_MAX_FLASH_BANKS	1   /* max num of flash banks	*/
-#define CONFIG_SYS_MAX_FLASH_SECT	512 /* max num of sects on one chip */
-#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE }
-
-/*
- * PRIO1/PIGGY on the local bus CS1
- */
-
-
-/*
- * Serial Port
- */
-#define CONFIG_SYS_NS16550_SERIAL
-#define CONFIG_SYS_NS16550_REG_SIZE	1
-#define CONFIG_SYS_NS16550_CLK		get_bus_freq(0)
-
-#define CONFIG_SYS_NS16550_COM1	(CONFIG_SYS_IMMR+0x4500)
-#define CONFIG_SYS_NS16550_COM2	(CONFIG_SYS_IMMR+0x4600)
-
-/*
- * QE UEC ethernet configuration
- */
-#define CONFIG_UEC_ETH
-#define CONFIG_ETHPRIME		"UEC0"
-
-#define CONFIG_UEC_ETH1		/* GETH1 */
-#define UEC_VERBOSE_DEBUG	1
-
-#ifdef CONFIG_UEC_ETH1
-#define CONFIG_SYS_UEC1_UCC_NUM	3	/* UCC4 */
-#define CONFIG_SYS_UEC1_RX_CLK		QE_CLK_NONE /* not used in RMII Mode */
-#define CONFIG_SYS_UEC1_TX_CLK		QE_CLK17
-#define CONFIG_SYS_UEC1_ETH_TYPE	FAST_ETH
-#define CONFIG_SYS_UEC1_PHY_ADDR	0
-#define CONFIG_SYS_UEC1_INTERFACE_TYPE	PHY_INTERFACE_MODE_RMII
-#define CONFIG_SYS_UEC1_INTERFACE_SPEED	100
-#endif
-
-/*
- * Environment
- */
-
-#ifndef CONFIG_SYS_RAMBOOT
-#ifndef CONFIG_ENV_ADDR
-#define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE + \
-					CONFIG_SYS_MONITOR_LEN)
-#endif
-#define CONFIG_ENV_SECT_SIZE	0x20000 /* 128K(one sector) for env */
-#ifndef CONFIG_ENV_OFFSET
-#define CONFIG_ENV_OFFSET	(CONFIG_SYS_MONITOR_LEN)
-#endif
-
-/* Address and size of Redundant Environment Sector	*/
-#define CONFIG_ENV_OFFSET_REDUND	(CONFIG_ENV_OFFSET + \
-						CONFIG_ENV_SECT_SIZE)
-#define CONFIG_ENV_SIZE_REDUND	(CONFIG_ENV_SIZE)
-
-#else /* CFG_SYS_RAMBOOT */
-#define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE - 0x1000)
-#define CONFIG_ENV_SIZE		0x2000
-#endif /* CFG_SYS_RAMBOOT */
-
-/* I2C */
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_NUM_I2C_BUSES	4
-#define CONFIG_SYS_I2C_MAX_HOPS		1
-#define CONFIG_SYS_I2C_FSL
-#define CONFIG_SYS_FSL_I2C_SPEED	200000
-#define CONFIG_SYS_FSL_I2C_SLAVE	0x7F
-#define CONFIG_SYS_FSL_I2C_OFFSET	0x3000
-#define CONFIG_SYS_I2C_OFFSET		0x3000
-#define CONFIG_SYS_FSL_I2C2_SPEED	200000
-#define CONFIG_SYS_FSL_I2C2_SLAVE	0x7F
-#define CONFIG_SYS_FSL_I2C2_OFFSET	0x3100
-#define CONFIG_SYS_I2C_BUSES	{{0, {I2C_NULL_HOP} }, \
-		{0, {{I2C_MUX_PCA9547, 0x70, 2} } }, \
-		{0, {{I2C_MUX_PCA9547, 0x70, 1} } }, \
-		{1, {I2C_NULL_HOP} } }
-
-#define CONFIG_KM_IVM_BUS		2	/* I2C2 (Mux-Port 1)*/
-
-#if defined(CONFIG_CMD_NAND)
-#define CONFIG_NAND_KMETER1
-#define CONFIG_SYS_MAX_NAND_DEVICE	1
-#define CONFIG_SYS_NAND_BASE		CONFIG_SYS_KMBEC_FPGA_BASE
-#endif
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_SYS_BOOTMAPSZ		(8 << 20)
-
-/*
- * Internal Definitions
- */
-#define BOOTFLASH_START	0xF0000000
-
-#define CONFIG_KM_CONSOLE_TTY	"ttyS0"
-
-/*
- * Environment Configuration
- */
-#define CONFIG_ENV_OVERWRITE
-#ifndef CONFIG_KM_DEF_ENV		/* if not set by keymile-common.h */
-#define CONFIG_KM_DEF_ENV "km-common=empty\0"
-#endif
-
-#ifndef CONFIG_KM_DEF_ARCH
-#define CONFIG_KM_DEF_ARCH	"arch=ppc_82xx\0"
-#endif
-
-#define CONFIG_EXTRA_ENV_SETTINGS \
-	CONFIG_KM_DEF_ENV						\
-	CONFIG_KM_DEF_ARCH						\
-	"newenv="							\
-		"prot off "__stringify(CONFIG_ENV_ADDR)" +0x40000 && "	\
-		"era "__stringify(CONFIG_ENV_ADDR)" +0x40000\0"		\
-	"unlock=yes\0"							\
-	""
-
-#if defined(CONFIG_UEC_ETH)
-#define CONFIG_HAS_ETH0
-#endif
-
-/*
- * System IO Config
- */
-#define CONFIG_SYS_SICRL	SICRL_IRQ_CKS
-
-#define CONFIG_SYS_DDRCDR (\
-	DDRCDR_EN | \
-	DDRCDR_PZ_MAXZ | \
-	DDRCDR_NZ_MAXZ | \
-	DDRCDR_M_ODR)
-
-#define CONFIG_SYS_DDR_CS0_BNDS		0x0000007f
-#define CONFIG_SYS_DDR_SDRAM_CFG	(SDRAM_CFG_SDRAM_TYPE_DDR2 | \
-					 SDRAM_CFG_32_BE | \
-					 SDRAM_CFG_SREN | \
-					 SDRAM_CFG_HSE)
-
-#define CONFIG_SYS_DDR_SDRAM_CFG2	0x00401000
-#define CONFIG_SYS_DDR_CLK_CNTL		(DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05)
-#define CONFIG_SYS_DDR_INTERVAL	((0x064 << SDRAM_INTERVAL_BSTOPRE_SHIFT) | \
-				 (0x200 << SDRAM_INTERVAL_REFINT_SHIFT))
-
-#define CONFIG_SYS_DDR_CS0_CONFIG	(CSCONFIG_EN | CSCONFIG_AP | \
-					 CSCONFIG_ODT_WR_CFG | \
-					 CSCONFIG_ROW_BIT_13 | \
-					 CSCONFIG_COL_BIT_10)
-
-#define CONFIG_SYS_DDR_MODE	0x47860242
-#define CONFIG_SYS_DDR_MODE2	0x8080c000
-
-#define CONFIG_SYS_DDR_TIMING_0	((2 << TIMING_CFG0_MRS_CYC_SHIFT) | \
-				 (8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) | \
-				 (2 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) | \
-				 (2 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) | \
-				 (0 << TIMING_CFG0_WWT_SHIFT) | \
-				 (0 << TIMING_CFG0_RRT_SHIFT) | \
-				 (0 << TIMING_CFG0_WRT_SHIFT) | \
-				 (0 << TIMING_CFG0_RWT_SHIFT))
-
-#define CONFIG_SYS_DDR_TIMING_1	((TIMING_CFG1_CASLAT_40) | \
-				 (2 << TIMING_CFG1_WRTORD_SHIFT) | \
-				 (2 << TIMING_CFG1_ACTTOACT_SHIFT) | \
-				 (3 << TIMING_CFG1_WRREC_SHIFT) | \
-				 (7 << TIMING_CFG1_REFREC_SHIFT) | \
-				 (3 << TIMING_CFG1_ACTTORW_SHIFT) | \
-				 (7 << TIMING_CFG1_ACTTOPRE_SHIFT) | \
-				 (3 << TIMING_CFG1_PRETOACT_SHIFT))
-
-#define CONFIG_SYS_DDR_TIMING_2	((8 << TIMING_CFG2_FOUR_ACT_SHIFT) | \
-				 (3 << TIMING_CFG2_CKE_PLS_SHIFT) | \
-				 (2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) | \
-				 (2 << TIMING_CFG2_RD_TO_PRE_SHIFT) | \
-				 (3 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) | \
-				 (0 << TIMING_CFG2_ADD_LAT_SHIFT) | \
-				 (5 << TIMING_CFG2_CPO_SHIFT))
-
-#define CONFIG_SYS_DDR_TIMING_3	0x00000000
-
-#define CONFIG_SYS_KMBEC_FPGA_BASE	0xE8000000
-#define CONFIG_SYS_KMBEC_FPGA_SIZE	128
-
-/* EEprom support */
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN	1
-
-/*
- * Init Local Bus Memory Controller:
- *				      Device on board
- * Bank Bus     Machine PortSz Size   TUDA1  TUXA1  TUGE1   KMSUPX4 KMOPTI2
- * -----------------------------------------------------------------------------
- *  2   Local   GPCM    8 bit  256MB  PAXG   LPXF   PAXI    LPXF    PAXE
- *  3   Local   GPCM    8 bit  256MB  PINC3  PINC2  unused  unused  OPI2(16 bit)
- *
- *				      Device on board (continued)
- * Bank Bus     Machine PortSz Size   KMTEPR2
- * -----------------------------------------------------------------------------
- *  2   Local   GPCM    8 bit  256MB  NVRAM
- *  3   Local   GPCM    8 bit  256MB  TEP2 (16 bit)
- */
-
+#include "km/km-mpc83xx.h"
+#include "km/km-mpc832x.h"
 
 #endif /* __CONFIG_H */