board: pm9g45: Migrate to CONFIG_DM

Migrate the following options to CONFIG_DM:
  CONFIG_DM_GPIO
  CONFIG_DM_MMC
  CONFIG_DM_ETH
  CONFIG_DM_SERIAL
  CONFIG_DM_USB

Signed-off-by: Ilko Iliev <iliev@ronetix.at>

1 files changed, 91 insertions, 82 deletions

diff --git a/include/configs/pm9g45.h b/include/configs/pm9g45.h
index 46b8030894..e34873cea7 100644
--- a/include/configs/pm9g45.h
+++ b/include/configs/pm9g45.h
@@ -15,110 +15,119 @@
 #ifndef __CONFIG_H
 #define __CONFIG_H
 
-/*
- * SoC must be defined first, before hardware.h is included.
- * In this case SoC is defined in boards.cfg.
- */
-#include <asm/hardware.h>
-
-#define CONFIG_SYS_AT91_CPU_NAME	"AT91SAM9G45"
-
-#define CONFIG_MACH_TYPE	MACH_TYPE_PM9G45
-
 /* ARM asynchronous clock */
-#define CONFIG_SYS_AT91_MAIN_CLOCK	12000000 /* from 12 MHz crystal */
-#define CONFIG_SYS_AT91_SLOW_CLOCK	32768		/* slow clock xtal */
-
-#define CONFIG_ARCH_CPU_INIT
-
-#define CONFIG_CMDLINE_TAG	1	/* enable passing of ATAGs */
-#define CONFIG_SETUP_MEMORY_TAGS 1
-#define CONFIG_INITRD_TAG	1
+#define CONFIG_SYS_AT91_SLOW_CLOCK      32768
+#define CONFIG_SYS_AT91_MAIN_CLOCK      12000000 /* from 12 MHz crystal */
 
+#define CONFIG_CMDLINE_TAG		/* enable passing of ATAGs	*/
+#define CONFIG_SETUP_MEMORY_TAGS
+#define CONFIG_INITRD_TAG
 #define CONFIG_SKIP_LOWLEVEL_INIT
 
-/*
- * Hardware drivers
- */
-#define CONFIG_AT91_GPIO	1
-#define CONFIG_ATMEL_USART	1
-#define CONFIG_USART_BASE		ATMEL_BASE_DBGU
-#define	CONFIG_USART_ID			ATMEL_ID_SYS
-
-#define CONFIG_SYS_USE_NANDFLASH	1
-
-/* LED */
-#define CONFIG_AT91_LED
-#define CONFIG_RED_LED		GPIO_PIN_PD(31) /* this is the user1 led */
-#define CONFIG_GREEN_LED	GPIO_PIN_PD(0)  /* this is the user2 led */
-
+/* general purpose I/O */
+#define CONFIG_ATMEL_LEGACY		/* required until (g)pio is fixed */
 
 /*
  * BOOTP options
  */
-#define CONFIG_BOOTP_BOOTFILESIZE	1
-
-#define CONFIG_JFFS2_CMDLINE		1
-#define CONFIG_JFFS2_NAND		1
-#define CONFIG_JFFS2_DEV		"nand0" /* NAND dev jffs2 lives on */
-#define CONFIG_JFFS2_PART_OFFSET	0	/* start of jffs2 partition */
-#define CONFIG_JFFS2_PART_SIZE		(256 * 1024 * 1024) /* partition */
+#define CONFIG_BOOTP_BOOTFILESIZE
 
 /* SDRAM */
-#define PHYS_SDRAM			0x70000000
-#define PHYS_SDRAM_SIZE			0x08000000	/* 128 megs */
+#define CONFIG_SYS_SDRAM_BASE           0x70000000
+#define CONFIG_SYS_SDRAM_SIZE		0x08000000
+
+#define CONFIG_SYS_INIT_SP_ADDR \
+	(CONFIG_SYS_SDRAM_BASE + 16 * 1024 - GENERATED_GBL_DATA_SIZE)
 
 /* NAND flash */
 #ifdef CONFIG_CMD_NAND
-#define CONFIG_SYS_MAX_NAND_DEVICE	1
-#define CONFIG_SYS_NAND_BASE		0x40000000
-#define CONFIG_SYS_NAND_DBW_8		1
+#define CONFIG_SYS_MAX_NAND_DEVICE		1
+#define CONFIG_SYS_NAND_BASE			ATMEL_BASE_CS3
+#define CONFIG_SYS_NAND_DBW_8
 /* our ALE is AD21 */
-#define CONFIG_SYS_NAND_MASK_ALE	(1 << 21)
+#define CONFIG_SYS_NAND_MASK_ALE		BIT(21)
 /* our CLE is AD22 */
-#define CONFIG_SYS_NAND_MASK_CLE	(1 << 22)
-#define CONFIG_SYS_NAND_ENABLE_PIN	GPIO_PIN_PC(14)
-#define CONFIG_SYS_NAND_READY_PIN	GPIO_PIN_PD(3)
-
+#define CONFIG_SYS_NAND_MASK_CLE		BIT(22)
+#define CONFIG_SYS_NAND_ENABLE_PIN		AT91_PIN_PC14
+#define CONFIG_SYS_NAND_READY_PIN		AT91_PIN_PD3
+#define CONFIG_SYS_NAND_DRIVER_ECC_LAYOUT
 #endif
 
 /* Ethernet */
-#define CONFIG_MACB			1
-#define CONFIG_RMII			1
-#define CONFIG_NET_RETRY_COUNT		20
-#define CONFIG_RESET_PHY_R		1
-
-/* USB */
-#define CONFIG_USB_ATMEL
-#define CONFIG_USB_ATMEL_CLK_SEL_UPLL
-#define CONFIG_USB_OHCI_NEW		1
-#define CONFIG_SYS_USB_OHCI_CPU_INIT	1
-#define CONFIG_SYS_USB_OHCI_REGS_BASE	0x00700000 /* _UHP_OHCI_BASE */
-#define CONFIG_SYS_USB_OHCI_SLOT_NAME	"at91sam9g45"
-#define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS	2
-
-/* board specific(not enough SRAM) */
-#define CONFIG_AT91SAM9G45_LCD_BASE	PHYS_SDRAM + 0xE00000
-
-#define CONFIG_SYS_LOAD_ADDR		PHYS_SDRAM + 0x2000000 /* load addr */
-
-#define CONFIG_SYS_MEMTEST_START	PHYS_SDRAM
-#define CONFIG_SYS_MEMTEST_END		CONFIG_AT91SAM9G45_LCD_BASE
-
-/* bootstrap + u-boot + env + linux in nandflash */
-#define CONFIG_ENV_OFFSET		0x60000
-#define CONFIG_ENV_OFFSET_REDUND	0x80000
-#define CONFIG_ENV_SIZE			0x20000		/* 1 sector = 128 kB */
-#define CONFIG_BOOTCOMMAND	"nand read 0x72000000 0x200000 0x200000; bootm"
+#define CONFIG_RESET_PHY_R
+#define CONFIG_AT91_WANTS_COMMON_PHY
+
+#define CONFIG_SYS_LOAD_ADDR		0x22000000	/* load address */
+
+#define CONFIG_SYS_MEMTEST_START	CONFIG_SYS_SDRAM_BASE
+#define CONFIG_SYS_MEMTEST_END		0x23e00000
+
+#ifdef CONFIG_NAND_BOOT
+/* bootstrap + u-boot + env in nandflash */
+#define CONFIG_ENV_OFFSET		0x140000
+#define CONFIG_ENV_OFFSET_REDUND	0x100000
+#define CONFIG_ENV_SIZE			0x20000
+
+#define CONFIG_BOOTCOMMAND						\
+	"nand read 0x70000000 0x200000 0x300000;"			\
+	"bootm 0x70000000"
+#elif CONFIG_SD_BOOT
+/* bootstrap + u-boot + env + linux in mmc */
+#define CONFIG_ENV_SIZE		0x4000
+
+#define CONFIG_BOOTCOMMAND	"fatload mmc 0:1 0x71000000 dtb; " \
+				"fatload mmc 0:1 0x72000000 zImage; " \
+				"bootz 0x72000000 - 0x71000000"
+#endif
 
 /*
  * Size of malloc() pool
  */
-#define CONFIG_SYS_MALLOC_LEN		ROUND(3 * CONFIG_ENV_SIZE + 128*1024,\
-					0x1000)
+#define CONFIG_SYS_MALLOC_LEN		ROUND(3 * CONFIG_ENV_SIZE + \
+					      128 * 1024, 0x1000)
+
+/* Defines for SPL */
+#define CONFIG_SPL_TEXT_BASE		0x300000
+#define CONFIG_SPL_MAX_SIZE		0x010000
+#define CONFIG_SPL_STACK		0x310000
+
+#define CONFIG_SYS_MONITOR_LEN		0x80000
+
+#ifdef CONFIG_SD_BOOT
+
+#define CONFIG_SPL_BSS_START_ADDR	0x70000000
+#define CONFIG_SPL_BSS_MAX_SIZE		0x00080000
+#define CONFIG_SYS_SPL_MALLOC_START	0x70080000
+#define CONFIG_SYS_SPL_MALLOC_SIZE	0x00080000
+
+#define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION	1
+#define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME		"u-boot.img"
+
+#elif CONFIG_NAND_BOOT
+#define CONFIG_SPL_NAND_DRIVERS
+#define CONFIG_SPL_NAND_BASE
+#define CONFIG_SPL_NAND_ECC
+#define CONFIG_SPL_NAND_SOFTECC
+#define CONFIG_SYS_NAND_U_BOOT_OFFS	0x40000
+#define CONFIG_SYS_NAND_U_BOOT_SIZE	0x80000
+#define CONFIG_SYS_NAND_5_ADDR_CYCLE
+
+#define CONFIG_SYS_NAND_PAGE_SIZE	0x800
+#define CONFIG_SYS_NAND_BLOCK_SIZE	0x20000
+#define CONFIG_SYS_NAND_PAGE_COUNT	64
+#define CONFIG_SYS_NAND_BAD_BLOCK_POS	NAND_LARGE_BADBLOCK_POS
+#define CONFIG_SYS_NAND_ECCSIZE		256
+#define CONFIG_SYS_NAND_ECCBYTES	3
+#define CONFIG_SYS_NAND_OOBSIZE		64
+#define CONFIG_SYS_NAND_ECCPOS		{ 40, 41, 42, 43, 44, 45, 46, 47, \
+					  48, 49, 50, 51, 52, 53, 54, 55, \
+					  56, 57, 58, 59, 60, 61, 62, 63, }
+#endif
 
-#define CONFIG_SYS_SDRAM_BASE	PHYS_SDRAM
-#define CONFIG_SYS_INIT_SP_ADDR	(CONFIG_SYS_SDRAM_BASE + 0x1000 - \
-				GENERATED_GBL_DATA_SIZE)
+#define CONFIG_SPL_ATMEL_SIZE
+#define CONFIG_SYS_MASTER_CLOCK		132096000
+#define CONFIG_SYS_AT91_PLLA		0x20c73f03
+#define CONFIG_SYS_MCKR			0x1301
+#define CONFIG_SYS_MCKR_CSS		0x1302
 
 #endif