Merge branch 'master' of git://www.denx.de/git/u-boot-imx

Migrate CONFIG_ARCH_USE_MEMSET/MEMCPY with this merge.

Signed-off-by: Tom Rini <trini@konsulko.com>

11 files changed, 1514 insertions, 8 deletions

diff --git a/include/configs/apalis_imx6.h b/include/configs/apalis_imx6.h
new file mode 100644
index 0000000000..d3af2da44f
--- /dev/null
+++ b/include/configs/apalis_imx6.h
@@ -0,0 +1,337 @@
+/*
+ * Copyright 2013-2015 Toradex, Inc.
+ *
+ * Configuration settings for the Toradex Apalis iMX6
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+#include "mx6_common.h"
+#define CONFIG_SYS_THUMB_BUILD
+
+#undef CONFIG_DISPLAY_BOARDINFO
+#define CONFIG_DISPLAY_BOARDINFO_LATE	/* Calls show_board_info() */
+
+#define CONFIG_MACH_TYPE		4886
+
+#define CONFIG_SYS_GENERIC_BOARD
+
+#include <asm/arch/imx-regs.h>
+#include <asm/imx-common/gpio.h>
+
+#ifdef CONFIG_SPL
+#include "imx6_spl.h"
+#define CONFIG_SPL_PAD_TO		0x11000 /* 4k IVT/DCD, 64k SPL */
+#endif
+
+#define CONFIG_CMDLINE_TAG
+#define CONFIG_SETUP_MEMORY_TAGS
+#define CONFIG_INITRD_TAG
+#define CONFIG_REVISION_TAG
+#define CONFIG_SERIAL_TAG
+
+/* Size of malloc() pool */
+#define CONFIG_SYS_MALLOC_LEN		(32 * 1024 * 1024)
+
+#define CONFIG_BOARD_EARLY_INIT_F
+#define CONFIG_BOARD_LATE_INIT
+#define CONFIG_MISC_INIT_R
+
+#define CONFIG_MXC_UART
+#define CONFIG_MXC_UART_BASE		UART1_BASE
+
+/* Make the HW version stuff available in U-Boot env */
+#define CONFIG_VERSION_VARIABLE		/* ver environment variable */
+#define CONFIG_ENV_VARS_UBOOT_CONFIG
+#define CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG
+
+/* I2C Configs */
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_MXC
+#define CONFIG_SYS_I2C_MXC_I2C1         /* enable I2C bus 1 */
+#define CONFIG_SYS_I2C_MXC_I2C2         /* enable I2C bus 2 */
+#define CONFIG_SYS_I2C_MXC_I2C3         /* enable I2C bus 3 */
+#define CONFIG_SYS_I2C_SPEED		100000
+
+/* OCOTP Configs */
+#define CONFIG_CMD_FUSE
+#ifdef CONFIG_CMD_FUSE
+#define CONFIG_MXC_OCOTP
+#endif
+
+/* MMC Configs */
+#define CONFIG_FSL_ESDHC
+#define CONFIG_FSL_USDHC
+#define CONFIG_SYS_FSL_ESDHC_ADDR	0
+#define CONFIG_SYS_FSL_USDHC_NUM	3
+
+#define CONFIG_SUPPORT_EMMC_BOOT	/* eMMC specific */
+#define CONFIG_MMC
+#define CONFIG_GENERIC_MMC
+#define CONFIG_BOUNCE_BUFFER
+#define CONFIG_FAT_WRITE
+#define CONFIG_DOS_PARTITION
+
+#ifdef CONFIG_MX6Q
+#define CONFIG_CMD_SATA
+#endif
+
+/*
+ * SATA Configs
+ */
+#ifdef CONFIG_CMD_SATA
+#define CONFIG_DWC_AHSATA
+#define CONFIG_SYS_SATA_MAX_DEVICE	1
+#define CONFIG_DWC_AHSATA_PORT_ID	0
+#define CONFIG_DWC_AHSATA_BASE_ADDR	SATA_ARB_BASE_ADDR
+#define CONFIG_LBA48
+#define CONFIG_LIBATA
+#endif
+
+/* Network */
+#define CONFIG_FEC_MXC
+#define CONFIG_MII
+#define IMX_FEC_BASE			ENET_BASE_ADDR
+#define CONFIG_FEC_XCV_TYPE		RGMII
+#define CONFIG_ETHPRIME			"FEC"
+#define CONFIG_FEC_MXC_PHYADDR		6
+#define CONFIG_PHYLIB
+#define CONFIG_PHY_MICREL
+#define CONFIG_PHY_MICREL_KSZ9031
+#define CONFIG_IP_DEFRAG
+#define CONFIG_TFTP_BLOCKSIZE		4096
+#define CONFIG_TFTP_TSIZE
+
+/* USB Configs */
+/* Host */
+#define CONFIG_USB_HOST_ETHER
+#define CONFIG_USB_MAX_CONTROLLER_COUNT		2
+#define CONFIG_EHCI_HCD_INIT_AFTER_RESET	/* For OTG port */
+#define CONFIG_MXC_USB_PORTSC		(PORT_PTS_UTMI | PORT_PTS_PTW)
+#define CONFIG_MXC_USB_FLAGS		0
+#define CONFIG_USB_KEYBOARD
+#ifdef CONFIG_USB_KEYBOARD
+#define CONFIG_SYS_USB_EVENT_POLL
+#endif /* CONFIG_USB_KEYBOARD */
+/* Client */
+#define CONFIG_USB_GADGET_VBUS_DRAW	2
+#define CONFIG_USBD_HS
+
+#define CONFIG_USB_GADGET_MASS_STORAGE
+#define CONFIG_USB_FUNCTION_MASS_STORAGE
+#define CONFIG_G_DNL_MANUFACTURER	"Toradex"
+/* USB DFU */
+#define CONFIG_DFU_MMC
+
+/* Miscellaneous commands */
+#define CONFIG_CMD_BMODE
+#define CONFIG_MXC_GPIO
+
+/* Framebuffer and LCD */
+#define CONFIG_VIDEO_IPUV3
+#define CONFIG_SYS_CONSOLE_IS_IN_ENV
+#define CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE
+#define CONFIG_VIDEO_BMP_RLE8
+#define CONFIG_SPLASH_SCREEN
+#define CONFIG_SPLASH_SCREEN_ALIGN
+#define CONFIG_BMP_16BPP
+#define CONFIG_VIDEO_LOGO
+#define CONFIG_VIDEO_BMP_LOGO
+#define CONFIG_IPUV3_CLK		260000000
+#define CONFIG_CMD_HDMIDETECT
+#define CONFIG_CONSOLE_MUX
+#define CONFIG_IMX_HDMI
+#define CONFIG_IMX_VIDEO_SKIP
+#define CONFIG_CMD_BMP
+
+/* allow to overwrite serial and ethaddr */
+#define CONFIG_ENV_OVERWRITE
+#define CONFIG_CONS_INDEX		1
+#define CONFIG_BAUDRATE			115200
+
+/* Command definition */
+#undef CONFIG_CMD_LOADB
+#undef CONFIG_CMD_LOADS
+#undef CONFIG_CMD_NFS
+#undef CONFIG_CMD_FLASH
+
+#undef CONFIG_IPADDR
+#define CONFIG_IPADDR			192.168.10.2
+#define CONFIG_NETMASK			255.255.255.0
+#undef CONFIG_SERVERIP
+#define CONFIG_SERVERIP			192.168.10.1
+
+#define CONFIG_LOADADDR			0x12000000
+#define CONFIG_SYS_TEXT_BASE		0x17800000
+
+#ifdef CONFIG_CMD_SATA
+#define CONFIG_DRIVE_SATA "sata "
+#else
+#define CONFIG_DRIVE_SATA
+#endif
+
+#ifdef CONFIG_CMD_MMC
+#define CONFIG_DRIVE_MMC "mmc "
+#else
+#define CONFIG_DRIVE_MMC
+#endif
+
+#define CONFIG_DRIVE_TYPES CONFIG_DRIVE_SATA CONFIG_DRIVE_MMC
+
+#define DFU_ALT_EMMC_INFO \
+	"u-boot.imx raw 0x2 0x3ff mmcpart 0;" \
+	"boot part 0 1;" \
+	"rootfs part 0 2;" \
+	"uImage fat 0 1;" \
+	"imx6q-colibri-eval-v3.dtb fat 0 1;" \
+	"imx6q-colibri-cam-eval-v3.dtb fat 0 1"
+
+#define EMMC_BOOTCMD \
+	"emmcargs=ip=off root=/dev/mmcblk0p2 rw,noatime rootfstype=ext3 " \
+		"rootwait\0" \
+	"emmcboot=run setup; " \
+		"setenv bootargs ${defargs} ${emmcargs} ${setupargs} " \
+		"${vidargs}; echo Booting from internal eMMC chip...; "	\
+		"run emmcdtbload; load mmc 0:1 ${kernel_addr_r} " \
+		"${boot_file} && run fdt_fixup && " \
+		"bootm ${kernel_addr_r} ${dtbparam}\0" \
+	"emmcdtbload=setenv dtbparam; load mmc 0:1 ${fdt_addr_r} " \
+		"${fdt_file} && setenv dtbparam \" - ${fdt_addr_r}\" && true\0"
+
+#define MEM_LAYOUT_ENV_SETTINGS \
+	"fdt_addr_r=0x12000000\0" \
+	"fdt_high=0xffffffff\0" \
+	"initrd_high=0xffffffff\0" \
+	"kernel_addr_r=0x11000000\0" \
+	"ramdisk_addr_r=0x12100000\0"
+
+#define NFS_BOOTCMD \
+	"nfsargs=ip=:::::eth0:on root=/dev/nfs rw\0" \
+	"nfsboot=run setup; " \
+		"setenv bootargs ${defargs} ${nfsargs} ${setupargs} " \
+		"${vidargs}; echo Booting via DHCP/TFTP/NFS...; " \
+		"run nfsdtbload; dhcp ${kernel_addr_r} " \
+		"&& run fdt_fixup && bootm ${kernel_addr_r} ${dtbparam}\0" \
+	"nfsdtbload=setenv dtbparam; tftp ${fdt_addr_r} ${fdt_file} " \
+		"&& setenv dtbparam \" - ${fdt_addr_r}\" && true\0"
+
+#define SD_BOOTCMD						\
+	"sdargs=ip=off root=/dev/mmcblk1p2 rw,noatime rootfstype=ext3 " \
+		"rootwait\0" \
+	"sdboot=run setup; " \
+		"setenv bootargs ${defargs} ${sdargs} ${setupargs} " \
+		"${vidargs}; echo Booting from SD card; " \
+		"run sddtbload; load mmc 1:1 ${kernel_addr_r} " \
+		"${boot_file} && run fdt_fixup && " \
+		"bootm ${kernel_addr_r} ${dtbparam}\0" \
+	"sddtbload=setenv dtbparam; load mmc 1:1 ${fdt_addr_r} " \
+		"${fdt_file} && setenv dtbparam \" - ${fdt_addr_r}\" && true\0"
+
+#define USB_BOOTCMD \
+	"usbargs=ip=off root=/dev/sda2 rw,noatime rootfstype=ext3 " \
+		"rootwait\0" \
+	"usbboot=run setup; setenv bootargs ${defargs} ${setupargs} " \
+		"${usbargs} ${vidargs}; echo Booting from USB stick...; " \
+		"usb start && run usbdtbload; load usb 0:1 ${kernel_addr_r} " \
+		"${boot_file} && run fdt_fixup && " \
+		"bootm ${kernel_addr_r} ${dtbparam}\0" \
+	"usbdtbload=setenv dtbparam; load usb 0:1 ${fdt_addr_r} " \
+		"${fdt_file} && setenv dtbparam \" - ${fdt_addr_r}\" && true\0"
+
+#ifndef CONFIG_TDX_APALIS_IMX6_V1_0
+#define FDT_FILE "imx6q-apalis-eval.dtb"
+#define FDT_FILE_V1_0 "imx6q-apalis_v1_0-eval.dtb"
+#else
+#define FDT_FILE "imx6q-apalis_v1_0-eval.dtb"
+#endif
+#define CONFIG_EXTRA_ENV_SETTINGS \
+	"bootcmd=run emmcboot ; echo ; echo emmcboot failed ; " \
+		"run nfsboot ; echo ; echo nfsboot failed ; " \
+		"usb start ;" \
+		"setenv stdout serial,vga ; setenv stdin serial,usbkbd\0" \
+	"boot_file=uImage\0" \
+	"console=ttymxc0\0" \
+	"defargs=enable_wait_mode=off vmalloc=400M\0" \
+	"dfu_alt_info=" DFU_ALT_EMMC_INFO "\0" \
+	EMMC_BOOTCMD \
+	"fdt_file=" FDT_FILE "\0" \
+	"fdt_fixup=;\0" \
+	MEM_LAYOUT_ENV_SETTINGS \
+	NFS_BOOTCMD \
+	SD_BOOTCMD \
+	"setethupdate=if env exists ethaddr; then; else setenv ethaddr " \
+		"00:14:2d:00:00:00; fi; tftpboot ${loadaddr} " \
+		"flash_eth.img && source ${loadaddr}\0" \
+	"setsdupdate=setenv interface mmc; setenv drive 1; mmc rescan; load " \
+		"${interface} ${drive}:1 ${loadaddr} flash_blk.img && " \
+		"source ${loadaddr}\0" \
+	"setup=setenv setupargs fec_mac=${ethaddr} " \
+		"consoleblank=0 no_console_suspend=1 console=tty1 " \
+		"console=${console},${baudrate}n8\0 " \
+	"setupdate=run setsdupdate || run setusbupdate || run setethupdate\0" \
+	"setusbupdate=usb start && setenv interface usb; setenv drive 0; " \
+		"load ${interface} ${drive}:1 ${loadaddr} flash_blk.img && " \
+		"source ${loadaddr}\0" \
+	"splashpos=m,m\0" \
+	"vidargs=mxc_hdmi.only_cea=1 " \
+		"video=mxcfb0:dev=hdmi,1920x1080M@60,if=RGB24 " \
+		"video=mxcfb1:off video=mxcfb2:off video=mxcfb3:off " \
+		"fbmem=32M\0 "
+
+/* Miscellaneous configurable options */
+#define CONFIG_SYS_LONGHELP
+#define CONFIG_AUTO_COMPLETE
+#undef CONFIG_SYS_CBSIZE
+#define CONFIG_SYS_CBSIZE		1024
+#undef CONFIG_SYS_MAXARGS
+#define CONFIG_SYS_MAXARGS		48
+
+#define CONFIG_SYS_ALT_MEMTEST
+#define CONFIG_SYS_MEMTEST_START	0x10000000
+#define CONFIG_SYS_MEMTEST_END		0x10010000
+#define CONFIG_SYS_MEMTEST_SCRATCH	0x10800000
+
+#define CONFIG_SYS_LOAD_ADDR		CONFIG_LOADADDR
+
+#define CONFIG_CMDLINE_EDITING
+
+/* Physical Memory Map */
+#define CONFIG_NR_DRAM_BANKS		1
+#define PHYS_SDRAM			MMDC0_ARB_BASE_ADDR
+
+#define CONFIG_SYS_SDRAM_BASE		PHYS_SDRAM
+#define CONFIG_SYS_INIT_RAM_ADDR	IRAM_BASE_ADDR
+#define CONFIG_SYS_INIT_RAM_SIZE	IRAM_SIZE
+
+#define CONFIG_SYS_INIT_SP_OFFSET \
+	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_ADDR \
+	(CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
+
+/* FLASH and environment organization */
+#define CONFIG_SYS_NO_FLASH
+
+#define CONFIG_ENV_SIZE			(8 * 1024)
+
+#define CONFIG_ENV_IS_IN_MMC
+
+#if defined(CONFIG_ENV_IS_IN_MMC)
+/* Environment in eMMC, before config block at the end of 1st "boot sector" */
+#define CONFIG_ENV_OFFSET		(-CONFIG_ENV_SIZE + \
+					 CONFIG_TDX_CFG_BLOCK_OFFSET)
+#define CONFIG_SYS_MMC_ENV_DEV		0
+#define CONFIG_SYS_MMC_ENV_PART		1
+#endif
+
+#define CONFIG_OF_SYSTEM_SETUP
+
+#define CONFIG_CMD_TIME
+
+#define CONFIG_SUPPORT_RAW_INITRD
+
+#define CONFIG_CRC32_VERIFY
+
+#endif	/* __CONFIG_H */
diff --git a/include/configs/colibri_imx6.h b/include/configs/colibri_imx6.h
new file mode 100644
index 0000000000..86ed4d243d
--- /dev/null
+++ b/include/configs/colibri_imx6.h
@@ -0,0 +1,305 @@
+/*
+ * Copyright 2013-2015 Toradex, Inc.
+ *
+ * Configuration settings for the Toradex Colibri iMX6
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+#include "mx6_common.h"
+#define CONFIG_SYS_THUMB_BUILD
+
+#undef CONFIG_DISPLAY_BOARDINFO
+#define CONFIG_DISPLAY_BOARDINFO_LATE	/* Calls show_board_info() */
+
+#define CONFIG_SYS_GENERIC_BOARD
+
+#include <asm/arch/imx-regs.h>
+#include <asm/imx-common/gpio.h>
+
+#ifdef CONFIG_SPL
+#include "imx6_spl.h"
+#define CONFIG_SPL_PAD_TO		0x11000 /* 4k IVT/DCD, 64k SPL */
+#endif
+
+#define CONFIG_CMDLINE_TAG
+#define CONFIG_SETUP_MEMORY_TAGS
+#define CONFIG_INITRD_TAG
+#define CONFIG_REVISION_TAG
+#define CONFIG_SERIAL_TAG
+
+/* Size of malloc() pool */
+#define CONFIG_SYS_MALLOC_LEN		(32 * 1024 * 1024)
+
+#define CONFIG_BOARD_EARLY_INIT_F
+#define CONFIG_BOARD_LATE_INIT
+#define CONFIG_MISC_INIT_R
+
+#define CONFIG_MXC_UART
+#define CONFIG_MXC_UART_BASE		UART1_BASE
+
+/* Make the HW version stuff available in U-Boot env */
+#define CONFIG_VERSION_VARIABLE		/* ver environment variable */
+#define CONFIG_ENV_VARS_UBOOT_CONFIG
+#define CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG
+
+/* I2C Configs */
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_MXC
+#define CONFIG_SYS_I2C_MXC_I2C1         /* enable I2C bus 1 */
+#define CONFIG_SYS_I2C_MXC_I2C2         /* enable I2C bus 2 */
+#define CONFIG_SYS_I2C_MXC_I2C3         /* enable I2C bus 3 */
+#define CONFIG_SYS_I2C_SPEED		100000
+
+/* OCOTP Configs */
+#define CONFIG_CMD_FUSE
+#ifdef CONFIG_CMD_FUSE
+#define CONFIG_MXC_OCOTP
+#endif
+
+/* MMC Configs */
+#define CONFIG_FSL_ESDHC
+#define CONFIG_FSL_USDHC
+#define CONFIG_SYS_FSL_ESDHC_ADDR	0
+#define CONFIG_SYS_FSL_USDHC_NUM	2
+
+#define CONFIG_SUPPORT_EMMC_BOOT	/* eMMC specific */
+#define CONFIG_MMC
+#define CONFIG_GENERIC_MMC
+#define CONFIG_BOUNCE_BUFFER
+#define CONFIG_FAT_WRITE
+#define CONFIG_DOS_PARTITION
+
+/* Network */
+#define CONFIG_FEC_MXC
+#define CONFIG_MII
+#define IMX_FEC_BASE			ENET_BASE_ADDR
+#define CONFIG_FEC_XCV_TYPE		RMII
+#define CONFIG_ETHPRIME			"FEC"
+#define CONFIG_FEC_MXC_PHYADDR		1
+#define CONFIG_PHYLIB
+#define CONFIG_PHY_MICREL
+#define CONFIG_IP_DEFRAG
+#define CONFIG_TFTP_BLOCKSIZE		16352
+#define CONFIG_TFTP_TSIZE
+
+/* USB Configs */
+/* Host */
+#define CONFIG_USB_HOST_ETHER
+#define CONFIG_USB_MAX_CONTROLLER_COUNT		2
+#define CONFIG_EHCI_HCD_INIT_AFTER_RESET	/* For OTG port */
+#define CONFIG_MXC_USB_PORTSC		(PORT_PTS_UTMI | PORT_PTS_PTW)
+#define CONFIG_MXC_USB_FLAGS		0
+#define CONFIG_USB_KEYBOARD
+#ifdef CONFIG_USB_KEYBOARD
+#define CONFIG_SYS_USB_EVENT_POLL
+#endif /* CONFIG_USB_KEYBOARD */
+/* Client */
+#define CONFIG_USB_GADGET_VBUS_DRAW	2
+#define CONFIG_USBD_HS
+
+#define CONFIG_USB_GADGET_MASS_STORAGE
+#define CONFIG_USB_FUNCTION_MASS_STORAGE
+#define CONFIG_G_DNL_MANUFACTURER	"Toradex"
+/* USB DFU */
+#define CONFIG_DFU_MMC
+
+/* Miscellaneous commands */
+#define CONFIG_CMD_BMODE
+#define CONFIG_MXC_GPIO
+
+/* Framebuffer and LCD */
+#define CONFIG_VIDEO_IPUV3
+#define CONFIG_SYS_CONSOLE_IS_IN_ENV
+#define CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE
+#define CONFIG_VIDEO_BMP_RLE8
+#define CONFIG_SPLASH_SCREEN
+#define CONFIG_SPLASH_SCREEN_ALIGN
+#define CONFIG_BMP_16BPP
+#define CONFIG_VIDEO_LOGO
+#define CONFIG_VIDEO_BMP_LOGO
+#define CONFIG_IPUV3_CLK		260000000
+#define CONFIG_CMD_HDMIDETECT
+#define CONFIG_CONSOLE_MUX
+#define CONFIG_IMX_HDMI
+#define CONFIG_IMX_VIDEO_SKIP
+#define CONFIG_CMD_BMP
+
+/* allow to overwrite serial and ethaddr */
+#define CONFIG_ENV_OVERWRITE
+#define CONFIG_CONS_INDEX		1
+#define CONFIG_BAUDRATE			115200
+
+/* Command definition */
+#undef CONFIG_CMD_LOADB
+#undef CONFIG_CMD_LOADS
+#undef CONFIG_CMD_NFS
+#undef CONFIG_CMD_FLASH
+
+#undef CONFIG_IPADDR
+#define CONFIG_IPADDR			192.168.10.2
+#define CONFIG_NETMASK			255.255.255.0
+#undef CONFIG_SERVERIP
+#define CONFIG_SERVERIP			192.168.10.1
+
+#define CONFIG_LOADADDR			0x12000000
+#define CONFIG_SYS_TEXT_BASE		0x17800000
+
+#ifdef CONFIG_CMD_MMC
+#define CONFIG_DRIVE_MMC "mmc "
+#else
+#define CONFIG_DRIVE_MMC
+#endif
+
+#define CONFIG_DRIVE_TYPES CONFIG_DRIVE_MMC
+
+#define DFU_ALT_EMMC_INFO \
+	"u-boot.imx raw 0x2 0x3ff mmcpart 0;" \
+	"boot part 0 1;" \
+	"rootfs part 0 2;" \
+	"uImage fat 0 1;" \
+	"imx6q-colibri-eval-v3.dtb fat 0 1;" \
+	"imx6q-colibri-cam-eval-v3.dtb fat 0 1"
+
+#define EMMC_BOOTCMD \
+	"emmcargs=ip=off root=/dev/mmcblk0p2 rw,noatime rootfstype=ext3 " \
+		"rootwait\0" \
+	"emmcboot=run setup; " \
+		"setenv bootargs ${defargs} ${emmcargs} ${setupargs} " \
+		"${vidargs}; echo Booting from internal eMMC chip...; "	\
+		"run emmcdtbload; load mmc 0:1 ${kernel_addr_r} " \
+		"${boot_file} && run fdt_fixup && " \
+		"bootm ${kernel_addr_r} ${dtbparam}\0" \
+	"emmcdtbload=setenv dtbparam; load mmc 0:1 ${fdt_addr_r} " \
+		"${fdt_file} && setenv dtbparam \" - ${fdt_addr_r}\" && true\0"
+
+#define MEM_LAYOUT_ENV_SETTINGS \
+	"fdt_addr_r=0x12000000\0" \
+	"fdt_high=0xffffffff\0" \
+	"initrd_high=0xffffffff\0" \
+	"kernel_addr_r=0x11000000\0" \
+	"ramdisk_addr_r=0x12100000\0"
+
+#define NFS_BOOTCMD \
+	"nfsargs=ip=:::::eth0:on root=/dev/nfs rw\0" \
+	"nfsboot=run setup; " \
+		"setenv bootargs ${defargs} ${nfsargs} ${setupargs} " \
+		"${vidargs}; echo Booting via DHCP/TFTP/NFS...; " \
+		"run nfsdtbload; dhcp ${kernel_addr_r} " \
+		"&& run fdt_fixup && bootm ${kernel_addr_r} ${dtbparam}\0" \
+	"nfsdtbload=setenv dtbparam; tftp ${fdt_addr_r} ${fdt_file} " \
+		"&& setenv dtbparam \" - ${fdt_addr_r}\" && true\0"
+
+#define SD_BOOTCMD						\
+	"sdargs=ip=off root=/dev/mmcblk1p2 rw,noatime rootfstype=ext3 " \
+		"rootwait\0" \
+	"sdboot=run setup; " \
+		"setenv bootargs ${defargs} ${sdargs} ${setupargs} " \
+		"${vidargs}; echo Booting from SD card; " \
+		"run sddtbload; load mmc 1:1 ${kernel_addr_r} " \
+		"${boot_file} && run fdt_fixup && " \
+		"bootm ${kernel_addr_r} ${dtbparam}\0" \
+	"sddtbload=setenv dtbparam; load mmc 1:1 ${fdt_addr_r} " \
+		"${fdt_file} && setenv dtbparam \" - ${fdt_addr_r}\" && true\0"
+
+#define USB_BOOTCMD \
+	"usbargs=ip=off root=/dev/sda2 rw,noatime rootfstype=ext3 " \
+		"rootwait\0" \
+	"usbboot=run setup; setenv bootargs ${defargs} ${setupargs} " \
+		"${usbargs} ${vidargs}; echo Booting from USB stick...; " \
+		"usb start && run usbdtbload; load usb 0:1 ${kernel_addr_r} " \
+		"${boot_file} && run fdt_fixup && " \
+		"bootm ${kernel_addr_r} ${dtbparam}\0" \
+	"usbdtbload=setenv dtbparam; load usb 0:1 ${fdt_addr_r} " \
+		"${fdt_file} && setenv dtbparam \" - ${fdt_addr_r}\" && true\0"
+
+#define FDT_FILE "imx6dl-colibri-eval-v3.dtb"
+#define CONFIG_EXTRA_ENV_SETTINGS \
+	"bootcmd=run emmcboot ; echo ; echo emmcboot failed ; " \
+		"run nfsboot ; echo ; echo nfsboot failed ; " \
+		"usb start ;" \
+		"setenv stdout serial,vga ; setenv stdin serial,usbkbd\0" \
+	"boot_file=uImage\0" \
+	"console=ttymxc0\0" \
+	"defargs=enable_wait_mode=off galcore.contiguousSize=50331648\0" \
+	"dfu_alt_info=" DFU_ALT_EMMC_INFO "\0" \
+	EMMC_BOOTCMD \
+	"fdt_file=" FDT_FILE "\0" \
+	"fdt_fixup=;\0" \
+	MEM_LAYOUT_ENV_SETTINGS \
+	NFS_BOOTCMD \
+	SD_BOOTCMD \
+	"setethupdate=if env exists ethaddr; then; else setenv ethaddr " \
+		"00:14:2d:00:00:00; fi; tftpboot ${loadaddr} " \
+		"flash_eth.img && source ${loadaddr}\0" \
+	"setsdupdate=setenv interface mmc; setenv drive 1; mmc rescan; load " \
+		"${interface} ${drive}:1 ${loadaddr} flash_blk.img && " \
+		"source ${loadaddr}\0" \
+	"setup=setenv setupargs fec_mac=${ethaddr} " \
+		"consoleblank=0 no_console_suspend=1 console=tty1 " \
+		"console=${console},${baudrate}n8\0 " \
+	"setupdate=run setsdupdate || run setusbupdate || run setethupdate\0" \
+	"setusbupdate=usb start && setenv interface usb; setenv drive 0; " \
+		"load ${interface} ${drive}:1 ${loadaddr} flash_blk.img && " \
+		"source ${loadaddr}\0" \
+	"splashpos=m,m\0" \
+	"vidargs=video=mxcfb0:dev=lcd,640x480M@60,if=RGB666 " \
+		"video=mxcfb1:off fbmem=8M\0 "
+
+/* Miscellaneous configurable options */
+#define CONFIG_SYS_LONGHELP
+#define CONFIG_AUTO_COMPLETE
+#undef CONFIG_SYS_CBSIZE
+#define CONFIG_SYS_CBSIZE		1024
+#undef CONFIG_SYS_MAXARGS
+#define CONFIG_SYS_MAXARGS		48
+
+#define CONFIG_SYS_ALT_MEMTEST
+#define CONFIG_SYS_MEMTEST_START	0x10000000
+#define CONFIG_SYS_MEMTEST_END		0x10010000
+#define CONFIG_SYS_MEMTEST_SCRATCH	0x10800000
+
+#define CONFIG_SYS_LOAD_ADDR		CONFIG_LOADADDR
+
+#define CONFIG_CMDLINE_EDITING
+
+/* Physical Memory Map */
+#define CONFIG_NR_DRAM_BANKS		1
+#define PHYS_SDRAM			MMDC0_ARB_BASE_ADDR
+
+#define CONFIG_SYS_SDRAM_BASE		PHYS_SDRAM
+#define CONFIG_SYS_INIT_RAM_ADDR	IRAM_BASE_ADDR
+#define CONFIG_SYS_INIT_RAM_SIZE	IRAM_SIZE
+
+#define CONFIG_SYS_INIT_SP_OFFSET \
+	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_ADDR \
+	(CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
+
+/* FLASH and environment organization */
+#define CONFIG_SYS_NO_FLASH
+
+#define CONFIG_ENV_SIZE			(8 * 1024)
+
+#define CONFIG_ENV_IS_IN_MMC
+
+#if defined(CONFIG_ENV_IS_IN_MMC)
+/* Environment in eMMC, before config block at the end of 1st "boot sector" */
+#define CONFIG_ENV_OFFSET		(-CONFIG_ENV_SIZE + \
+					 CONFIG_TDX_CFG_BLOCK_OFFSET)
+#define CONFIG_SYS_MMC_ENV_DEV		0
+#define CONFIG_SYS_MMC_ENV_PART		1
+#endif
+
+#define CONFIG_OF_SYSTEM_SETUP
+
+#define CONFIG_CMD_TIME
+
+#define CONFIG_SUPPORT_RAW_INITRD
+
+#define CONFIG_CRC32_VERIFY
+
+#endif	/* __CONFIG_H */
diff --git a/include/configs/colibri_vf.h b/include/configs/colibri_vf.h
index 47dea625ed..62131c7359 100644
--- a/include/configs/colibri_vf.h
+++ b/include/configs/colibri_vf.h
@@ -97,7 +97,7 @@
 	"${setupargs} ${vidargs}; echo Booting from MMC/SD card...; " \
 	"load mmc 0:2 ${kernel_addr_r} /boot/${kernel_file} && " \
 	"load mmc 0:2 ${fdt_addr_r} /boot/${soc}-colibri-${fdt_board}.dtb && " \
-	"bootz ${kernel_addr_r} - ${fdt_addr_r}\0" \
+	"run fdt_fixup && bootz ${kernel_addr_r} - ${fdt_addr_r}\0" \
 
 #define NFS_BOOTCMD \
 	"nfsargs=ip=:::::eth0: root=/dev/nfs\0"	\
@@ -106,7 +106,7 @@
 	"${setupargs} ${vidargs}; echo Booting from NFS...;" \
 	"dhcp ${kernel_addr_r} && "	\
 	"tftp ${fdt_addr_r} ${soc}-colibri-${fdt_board}.dtb && " \
-	"bootz ${kernel_addr_r} - ${fdt_addr_r}\0" \
+	"run fdt_fixup && bootz ${kernel_addr_r} - ${fdt_addr_r}\0" \
 
 #define UBI_BOOTCMD	\
 	"ubiargs=ubi.mtd=ubi root=ubi0:rootfs rootfstype=ubifs " \
@@ -117,7 +117,7 @@
 	"ubi part ubi && " \
 	"ubi read ${kernel_addr_r} kernel && " \
 	"ubi read ${fdt_addr_r} dtb && " \
-	"bootz ${kernel_addr_r} - ${fdt_addr_r}\0" \
+	"run fdt_fixup && bootz ${kernel_addr_r} - ${fdt_addr_r}\0" \
 
 #define CONFIG_BOOTCOMMAND "run ubiboot; run sdboot; run nfsboot"
 
@@ -129,6 +129,7 @@
 	"kernel_file=zImage\0" \
 	"fdt_file=${soc}-colibri-${fdt_board}.dtb\0" \
 	"fdt_board=eval-v3\0" \
+	"fdt_fixup=;\0" \
 	"defargs=\0" \
 	"console=ttyLP0\0" \
 	"setup=setenv setupargs " \
diff --git a/include/configs/imx6qdl_icore.h b/include/configs/imx6qdl_icore.h
index f8a1263eed..204e96e017 100644
--- a/include/configs/imx6qdl_icore.h
+++ b/include/configs/imx6qdl_icore.h
@@ -37,6 +37,7 @@
 /* Default environment */
 #define CONFIG_EXTRA_ENV_SETTINGS \
 	"script=boot.scr\0" \
+	"splashpos=m,m\0" \
 	"image=zImage\0" \
 	"console=ttymxc3\0" \
 	"fdt_high=0xffffffff\0" \
@@ -149,6 +150,19 @@
 # define CONFIG_PHY_SMSC
 #endif
 
+/* Framebuffer */
+#ifdef CONFIG_VIDEO_IPUV3
+# define CONFIG_IPUV3_CLK		260000000
+# define CONFIG_IMX_VIDEO_SKIP
+
+# define CONFIG_SPLASH_SCREEN
+# define CONFIG_SPLASH_SCREEN_ALIGN
+# define CONFIG_BMP_16BPP
+# define CONFIG_VIDEO_BMP_RLE8
+# define CONFIG_VIDEO_LOGO
+# define CONFIG_VIDEO_BMP_LOGO
+#endif
+
 /* SPL */
 #ifdef CONFIG_SPL
 # ifdef CONFIG_NAND_MXS
diff --git a/include/configs/imx6qdl_icore_rqs.h b/include/configs/imx6qdl_icore_rqs.h
new file mode 100644
index 0000000000..01215631b6
--- /dev/null
+++ b/include/configs/imx6qdl_icore_rqs.h
@@ -0,0 +1,135 @@
+/*
+ * Copyright (C) 2016 Amarula Solutions B.V.
+ * Copyright (C) 2016 Engicam S.r.l.
+ *
+ * Configuration settings for the Engicam i.CoreM6 QDL RQS Starter Kits.
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#ifndef __IMX6QLD_ICORE_RQS_CONFIG_H
+#define __IMX6QLD_ICORE_RQS_CONFIG_H
+
+#include <linux/sizes.h>
+#include "mx6_common.h"
+
+/* Size of malloc() pool */
+#define CONFIG_SYS_MALLOC_LEN		(16 * SZ_1M)
+
+/* Total Size of Environment Sector */
+#define CONFIG_ENV_SIZE			SZ_128K
+
+/* Allow to overwrite serial and ethaddr */
+#define CONFIG_ENV_OVERWRITE
+
+/* Environment */
+#ifndef CONFIG_ENV_IS_NOWHERE
+/* Environment in MMC */
+# if defined(CONFIG_ENV_IS_IN_MMC)
+#  define CONFIG_ENV_OFFSET		0x100000
+# endif
+#endif
+
+/* Default environment */
+#define CONFIG_EXTRA_ENV_SETTINGS \
+	"script=boot.scr\0" \
+	"image=zImage\0" \
+	"console=ttymxc3\0" \
+	"fdt_high=0xffffffff\0" \
+	"fdt_file=" CONFIG_DEFAULT_FDT_FILE "\0" \
+	"fdt_addr=0x18000000\0" \
+	"boot_fdt=try\0" \
+	"mmcdev=0\0" \
+	"mmcpart=1\0" \
+	"mmcroot=/dev/mmcblk0p2 rootwait rw\0" \
+	"mmcautodetect=yes\0" \
+	"mmcargs=setenv bootargs console=${console},${baudrate} " \
+		"root=${mmcroot}\0" \
+	"loadbootscript=" \
+		"fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${script};\0" \
+	"bootscript=echo Running bootscript from mmc ...; " \
+		"source\0" \
+	"loadimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${image}\0" \
+	"loadfdt=fatload mmc ${mmcdev}:${mmcpart} ${fdt_addr} ${fdt_file}\0" \
+	"mmcboot=echo Booting from mmc ...; " \
+		"run mmcargs; " \
+		"if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
+			"if run loadfdt; then " \
+				"bootz ${loadaddr} - ${fdt_addr}; " \
+			"else " \
+				"if test ${boot_fdt} = try; then " \
+					"bootz; " \
+				"else " \
+					"echo WARN: Cannot load the DT; " \
+				"fi; " \
+			"fi; " \
+		"else " \
+			"bootz; " \
+		"fi\0"
+
+#define CONFIG_BOOTCOMMAND \
+	   "mmc dev ${mmcdev};" \
+	   "mmc dev ${mmcdev}; if mmc rescan; then " \
+		   "if run loadbootscript; then " \
+			   "run bootscript; " \
+		   "else " \
+			"if run loadimage; then " \
+				"run mmcboot; " \
+			"fi; " \
+		   "fi; " \
+	   "fi"
+
+/* Miscellaneous configurable options */
+#define CONFIG_SYS_MEMTEST_START	0x80000000
+#define CONFIG_SYS_MEMTEST_END		(CONFIG_SYS_MEMTEST_START + 0x8000000)
+
+#define CONFIG_SYS_LOAD_ADDR		CONFIG_LOADADDR
+#define CONFIG_SYS_HZ			1000
+
+/* Physical Memory Map */
+#define CONFIG_NR_DRAM_BANKS		1
+#define PHYS_SDRAM			MMDC0_ARB_BASE_ADDR
+
+#define CONFIG_SYS_SDRAM_BASE		PHYS_SDRAM
+#define CONFIG_SYS_INIT_RAM_ADDR	IRAM_BASE_ADDR
+#define CONFIG_SYS_INIT_RAM_SIZE	IRAM_SIZE
+
+#define CONFIG_SYS_INIT_SP_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - \
+					GENERATED_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_ADDR		(CONFIG_SYS_INIT_RAM_ADDR + \
+					CONFIG_SYS_INIT_SP_OFFSET)
+
+/* UART */
+#ifdef CONFIG_MXC_UART
+# define CONFIG_MXC_UART_BASE		UART4_BASE
+#endif
+
+/* MMC */
+#ifdef CONFIG_FSL_USDHC
+# define CONFIG_SYS_MMC_ENV_DEV		0
+# define CONFIG_SYS_FSL_USDHC_NUM	1
+# define CONFIG_SYS_FSL_ESDHC_ADDR	0
+#endif
+
+/* Ethernet */
+#ifdef CONFIG_FEC_MXC
+# define CONFIG_FEC_MXC_PHYADDR		3
+# define CONFIG_FEC_XCV_TYPE		RGMII
+
+# define CONFIG_MII
+# define CONFIG_PHYLIB
+# define CONFIG_PHY_MICREL
+# define CONFIG_PHY_MICREL_KSZ9021
+#endif
+
+/* SPL */
+#ifdef CONFIG_SPL
+# define CONFIG_SPL_MMC_SUPPORT
+# include "imx6_spl.h"
+# ifdef CONFIG_SPL_BUILD
+#  undef CONFIG_DM_GPIO
+#  undef CONFIG_DM_MMC
+# endif
+#endif
+
+#endif /* __IMX6QLD_ICORE_RQS_CONFIG_H */
diff --git a/include/configs/imx6ul_geam.h b/include/configs/imx6ul_geam.h
new file mode 100644
index 0000000000..48b1120910
--- /dev/null
+++ b/include/configs/imx6ul_geam.h
@@ -0,0 +1,165 @@
+/*
+ * Copyright (C) 2016 Amarula Solutions B.V.
+ * Copyright (C) 2016 Engicam S.r.l.
+ *
+ * Configuration settings for the Engicam GEAM6UL  Starter Kits.
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#ifndef __IMX6UL_GEAM_CONFIG_H
+#define __IMX6UL_GEAM_CONFIG_H
+
+#include <linux/sizes.h>
+#include "mx6_common.h"
+
+/* Size of malloc() pool */
+#define CONFIG_SYS_MALLOC_LEN		(16 * SZ_1M)
+
+/* Total Size of Environment Sector */
+#define CONFIG_ENV_SIZE			SZ_128K
+
+/* Allow to overwrite serial and ethaddr */
+#define CONFIG_ENV_OVERWRITE
+
+/* Environment */
+#ifndef CONFIG_ENV_IS_NOWHERE
+/* Environment in MMC */
+# if defined(CONFIG_ENV_IS_IN_MMC)
+#  define CONFIG_ENV_OFFSET		0x100000
+/* Environment in NAND */
+# elif defined(CONFIG_ENV_IS_IN_NAND)
+#  define CONFIG_ENV_OFFSET		0x400000
+#  define CONFIG_ENV_SECT_SIZE		CONFIG_ENV_SIZE
+# endif
+#endif
+
+/* Default environment */
+#define CONFIG_EXTRA_ENV_SETTINGS \
+	"script=boot.scr\0" \
+	"image=zImage\0" \
+	"console=ttymxc0\0" \
+	"fdt_high=0xffffffff\0" \
+	"fdt_file=" CONFIG_DEFAULT_FDT_FILE "\0" \
+	"fdt_addr=0x87800000\0" \
+	"boot_fdt=try\0" \
+	"mmcdev=0\0" \
+	"mmcpart=1\0" \
+	"mmcroot=/dev/mmcblk0p2 rootwait rw\0" \
+	"mmcautodetect=yes\0" \
+	"mmcargs=setenv bootargs console=${console},${baudrate} " \
+		"root=${mmcroot}\0" \
+	"loadbootscript=" \
+		"fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${script};\0" \
+	"bootscript=echo Running bootscript from mmc ...; " \
+		"source\0" \
+	"loadimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${image}\0" \
+	"loadfdt=fatload mmc ${mmcdev}:${mmcpart} ${fdt_addr} ${fdt_file}\0" \
+	"mmcboot=echo Booting from mmc ...; " \
+		"run mmcargs; " \
+		"if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
+			"if run loadfdt; then " \
+				"bootz ${loadaddr} - ${fdt_addr}; " \
+			"else " \
+				"if test ${boot_fdt} = try; then " \
+					"bootz; " \
+				"else " \
+					"echo WARN: Cannot load the DT; " \
+				"fi; " \
+			"fi; " \
+		"else " \
+			"bootz; " \
+		"fi\0"
+
+#define CONFIG_BOOTCOMMAND \
+	   "mmc dev ${mmcdev};" \
+	   "mmc dev ${mmcdev}; if mmc rescan; then " \
+		   "if run loadbootscript; then " \
+			   "run bootscript; " \
+		   "else " \
+			"if run loadimage; then " \
+				"run mmcboot; " \
+			"fi; " \
+		   "fi; " \
+	   "fi"
+
+/* Miscellaneous configurable options */
+#define CONFIG_SYS_MEMTEST_START	0x80000000
+#define CONFIG_SYS_MEMTEST_END		(CONFIG_SYS_MEMTEST_START + 0x8000000)
+
+#define CONFIG_SYS_LOAD_ADDR		CONFIG_LOADADDR
+#define CONFIG_SYS_HZ			1000
+
+/* Physical Memory Map */
+#define CONFIG_NR_DRAM_BANKS		1
+#define PHYS_SDRAM			MMDC0_ARB_BASE_ADDR
+
+#define CONFIG_SYS_SDRAM_BASE		PHYS_SDRAM
+#define CONFIG_SYS_INIT_RAM_ADDR	IRAM_BASE_ADDR
+#define CONFIG_SYS_INIT_RAM_SIZE	IRAM_SIZE
+
+#define CONFIG_SYS_INIT_SP_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - \
+					GENERATED_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_ADDR		(CONFIG_SYS_INIT_RAM_ADDR + \
+					CONFIG_SYS_INIT_SP_OFFSET)
+
+/* UART */
+#ifdef CONFIG_MXC_UART
+# define CONFIG_MXC_UART_BASE		UART1_BASE
+#endif
+
+/* MMC */
+#ifdef CONFIG_FSL_USDHC
+# define CONFIG_SYS_MMC_ENV_DEV		0
+# define CONFIG_SYS_FSL_USDHC_NUM	1
+# define CONFIG_SYS_FSL_ESDHC_ADDR	USDHC2_BASE_ADDR
+#endif
+
+/* NAND */
+#ifdef CONFIG_NAND_MXS
+# define CONFIG_SYS_MAX_NAND_DEVICE	1
+# define CONFIG_SYS_NAND_BASE		0x40000000
+# define CONFIG_SYS_NAND_5_ADDR_CYCLE
+# define CONFIG_SYS_NAND_ONFI_DETECTION
+# define CONFIG_SYS_NAND_U_BOOT_START	CONFIG_SYS_TEXT_BASE
+# define CONFIG_SYS_NAND_U_BOOT_OFFS	0x200000
+
+/* MTD device */
+# define CONFIG_MTD_DEVICE
+# define CONFIG_CMD_MTDPARTS
+# define CONFIG_MTD_PARTITIONS
+# define MTDIDS_DEFAULT			"nand0=nand"
+# define MTDPARTS_DEFAULT		"mtdparts=nand:2m(spl),2m(uboot)," \
+					"1m(env),4m(kernel),1m(dtb),-(rootfs)"
+
+# define CONFIG_APBH_DMA
+# define CONFIG_APBH_DMA_BURST
+# define CONFIG_APBH_DMA_BURST8
+#endif
+
+/* Ethernet */
+#ifdef CONFIG_FEC_MXC
+# define CONFIG_FEC_MXC_PHYADDR		0
+# define CONFIG_FEC_XCV_TYPE		RMII
+
+# define CONFIG_MII
+# define CONFIG_PHYLIB
+# define CONFIG_PHY_SMSC
+#endif
+
+/* SPL */
+#ifdef CONFIG_SPL
+# ifdef CONFIG_NAND_MXS
+#  define CONFIG_SPL_NAND_SUPPORT
+# else
+#  define CONFIG_SPL_MMC_SUPPORT
+# endif
+
+# include "imx6_spl.h"
+# ifdef CONFIG_SPL_BUILD
+#  undef CONFIG_DM_GPIO
+#  undef CONFIG_DM_MMC
+# endif
+#endif
+
+#endif /* __IMX6UL_GEAM_CONFIG_H */
diff --git a/include/configs/liteboard.h b/include/configs/liteboard.h
new file mode 100644
index 0000000000..a55d76760c
--- /dev/null
+++ b/include/configs/liteboard.h
@@ -0,0 +1,171 @@
+/*
+ * Copyright (C) 2015 Freescale Semiconductor, Inc.
+ * Copyright (C) 2016 Grinn
+ *
+ * Configuration settings for the Grinn liteBoard (i.MX6UL).
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+#ifndef __LITEBOARD_CONFIG_H
+#define __LITEBOARD_CONFIG_H
+
+#include <asm/arch/imx-regs.h>
+#include <linux/sizes.h>
+#include "mx6_common.h"
+
+/* SPL options */
+#include "imx6_spl.h"
+
+/* Size of malloc() pool */
+#define CONFIG_SYS_MALLOC_LEN		(16 * SZ_1M)
+
+#define CONFIG_BOARD_EARLY_INIT_F
+#define CONFIG_BOARD_LATE_INIT
+
+#define CONFIG_MXC_UART
+#define CONFIG_MXC_UART_BASE		UART1_BASE
+
+/* MMC Configs */
+#ifdef CONFIG_FSL_USDHC
+#define CONFIG_SYS_FSL_ESDHC_ADDR	USDHC1_BASE_ADDR
+#define CONFIG_SUPPORT_EMMC_BOOT
+#endif
+
+#define CONFIG_SYS_MMC_IMG_LOAD_PART	1
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+	"script=boot.scr\0" \
+	"image=zImage\0" \
+	"console=ttymxc0\0" \
+	"fdt_high=0xffffffff\0" \
+	"initrd_high=0xffffffff\0" \
+	"fdt_file=" CONFIG_DEFAULT_FDT_FILE "\0" \
+	"fdt_addr=0x83000000\0" \
+	"boot_fdt=try\0" \
+	"ip_dyn=yes\0" \
+	"mmcdev="__stringify(CONFIG_SYS_MMC_ENV_DEV)"\0" \
+	"mmcpart=" __stringify(CONFIG_SYS_MMC_IMG_LOAD_PART) "\0" \
+	"mmcroot=" CONFIG_MMCROOT " rootwait rw\0" \
+	"mmcautodetect=yes\0" \
+	"mmcargs=setenv bootargs console=${console},${baudrate} " \
+		"root=${mmcroot}\0" \
+	"loadbootscript=" \
+		"fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${script};\0" \
+	"bootscript=echo Running bootscript from mmc ...; " \
+		"source\0" \
+	"loadimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${image}\0" \
+	"loadfdt=fatload mmc ${mmcdev}:${mmcpart} ${fdt_addr} ${fdt_file}\0" \
+	"mmcboot=echo Booting from mmc ...; " \
+		"run mmcargs; " \
+		"if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
+			"if run loadfdt; then " \
+				"bootz ${loadaddr} - ${fdt_addr}; " \
+			"else " \
+				"if test ${boot_fdt} = try; then " \
+					"bootz; " \
+				"else " \
+					"echo WARN: Cannot load the DT; " \
+				"fi; " \
+			"fi; " \
+		"else " \
+			"bootz; " \
+		"fi;\0" \
+	"netargs=setenv bootargs console=${console},${baudrate} " \
+		"root=/dev/nfs " \
+	"ip=dhcp nfsroot=${serverip}:${nfsroot},v3,tcp\0" \
+	"netboot=echo Booting from net ...; " \
+		"run netargs; " \
+		"if test ${ip_dyn} = yes; then " \
+			"setenv get_cmd dhcp; " \
+		"else " \
+			"setenv get_cmd tftp; " \
+		"fi; " \
+		"${get_cmd} ${image}; " \
+		"if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
+			"if ${get_cmd} ${fdt_addr} ${fdt_file}; then " \
+				"bootz ${loadaddr} - ${fdt_addr}; " \
+			"else " \
+				"if test ${boot_fdt} = try; then " \
+					"bootz; " \
+				"else " \
+					"echo WARN: Cannot load the DT; " \
+				"fi; " \
+			"fi; " \
+		"else " \
+			"bootz; " \
+		"fi;\0"
+
+#define CONFIG_BOOTCOMMAND \
+	   "mmc dev ${mmcdev};" \
+	   "if mmc rescan; then " \
+		   "if run loadbootscript; then " \
+			   "run bootscript; " \
+		   "else " \
+			   "if run loadimage; then " \
+				   "run mmcboot; " \
+			   "else run netboot; " \
+			   "fi; " \
+		   "fi; " \
+	   "else run netboot; fi"
+
+/* Miscellaneous configurable options */
+#define CONFIG_SYS_MEMTEST_START	0x80000000
+#define CONFIG_SYS_MEMTEST_END		(CONFIG_SYS_MEMTEST_START + SZ_128M)
+
+#define CONFIG_SYS_LOAD_ADDR		CONFIG_LOADADDR
+#define CONFIG_SYS_HZ			1000
+
+#define CONFIG_CMDLINE_EDITING
+#define CONFIG_STACKSIZE		SZ_128K
+
+/* Physical Memory Map */
+#define CONFIG_NR_DRAM_BANKS		1
+#define PHYS_SDRAM			MMDC0_ARB_BASE_ADDR
+
+#define CONFIG_SYS_SDRAM_BASE		PHYS_SDRAM
+#define CONFIG_SYS_INIT_RAM_ADDR	IRAM_BASE_ADDR
+#define CONFIG_SYS_INIT_RAM_SIZE	IRAM_SIZE
+
+#define CONFIG_SYS_INIT_SP_OFFSET \
+	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_ADDR \
+	(CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
+
+/* FLASH and environment organization */
+#define CONFIG_ENV_SIZE			SZ_8K
+#define CONFIG_ENV_IS_IN_MMC
+#define CONFIG_ENV_OFFSET		(8 * SZ_64K)
+#define CONFIG_SYS_MMC_ENV_DEV		0
+#define CONFIG_SYS_MMC_ENV_PART		0
+#define CONFIG_MMCROOT			"/dev/mmcblk0p2"
+
+#define CONFIG_CMD_BMODE
+
+/* USB Configs */
+#ifdef CONFIG_CMD_USB
+#define CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_MX6
+#define CONFIG_USB_STORAGE
+#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
+#define CONFIG_MXC_USB_PORTSC  (PORT_PTS_UTMI | PORT_PTS_PTW)
+#define CONFIG_MXC_USB_FLAGS   0
+#define CONFIG_USB_MAX_CONTROLLER_COUNT 1
+#endif
+
+#ifdef CONFIG_CMD_NET
+#define CONFIG_FEC_MXC
+#define CONFIG_MII
+#define CONFIG_FEC_ENET_DEV		0
+
+#define IMX_FEC_BASE			ENET_BASE_ADDR
+#define CONFIG_FEC_MXC_PHYADDR		0x0
+#define CONFIG_FEC_XCV_TYPE		RMII
+#define CONFIG_ETHPRIME			"FEC"
+
+#define CONFIG_PHYLIB
+#define CONFIG_PHY_SMSC
+#endif
+
+#define CONFIG_IMX_THERMAL
+
+#endif
diff --git a/include/configs/mx53cx9020.h b/include/configs/mx53cx9020.h
new file mode 100644
index 0000000000..87c75d4e53
--- /dev/null
+++ b/include/configs/mx53cx9020.h
@@ -0,0 +1,198 @@
+/*
+ * Copyright (C) 2015  Beckhoff Automation GmbH & Co. KG
+ * Patrick Bruenn <p.bruenn@beckhoff.com>
+ *
+ * Configuration settings for Beckhoff CX9020.
+ *
+ * Based on Freescale's Linux i.MX mx53loco.h file:
+ * Copyright (C) 2010-2011 Freescale Semiconductor.
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+#include <asm/arch/imx-regs.h>
+
+#define CONFIG_CMDLINE_TAG
+#define CONFIG_SETUP_MEMORY_TAGS
+#define CONFIG_INITRD_TAG
+
+#define CONFIG_SYS_FSL_CLK
+
+/* Size of malloc() pool */
+#define CONFIG_SYS_MALLOC_LEN		(10 * 1024 * 1024)
+
+#define CONFIG_BOARD_EARLY_INIT_F
+#define CONFIG_BOARD_LATE_INIT
+#define CONFIG_MXC_GPIO
+#define CONFIG_REVISION_TAG
+
+#define CONFIG_MXC_UART_BASE UART2_BASE
+
+#define CONFIG_FPGA_COUNT 1
+
+/* MMC Configs */
+#define CONFIG_FSL_ESDHC
+#define CONFIG_SYS_FSL_ESDHC_ADDR	0
+#define CONFIG_SYS_FSL_ESDHC_NUM	2
+
+#define CONFIG_MMC
+#define CONFIG_GENERIC_MMC
+
+/* bootz: zImage/initrd.img support */
+#define CONFIG_DOS_PARTITION
+
+/* Eth Configs */
+#define CONFIG_MII
+#define IMX_FEC_BASE	FEC_BASE_ADDR
+#define CONFIG_ETHPRIME		"FEC0"
+#define CONFIG_FEC_MXC_PHYADDR	0x1F
+
+/* USB Configs */
+#define CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_MX5
+#define CONFIG_USB_STORAGE
+#define CONFIG_USB_HOST_ETHER
+#define CONFIG_USB_ETHER_ASIX
+#define CONFIG_USB_ETHER_MCS7830
+#define CONFIG_USB_ETHER_SMSC95XX
+#define CONFIG_MXC_USB_PORT	1
+#define CONFIG_MXC_USB_PORTSC	(PORT_PTS_UTMI | PORT_PTS_PTW)
+#define CONFIG_MXC_USB_FLAGS	0
+
+/* allow to overwrite serial and ethaddr */
+#define CONFIG_ENV_OVERWRITE
+#define CONFIG_CONS_INDEX		1
+#define CONFIG_BAUDRATE			115200
+
+/* Command definition */
+#define CONFIG_SUPPORT_RAW_INITRD
+
+#define CONFIG_LOADADDR		0x70010000	/* loadaddr env var */
+#define CONFIG_SYS_TEXT_BASE    0x77800000
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+	"fdt_addr=0x71ff0000\0" \
+	"rdaddr=0x72000000\0" \
+	"console=ttymxc1,115200\0" \
+	"uenv=/boot/uEnv.txt\0" \
+	"optargs=\0" \
+	"cmdline=\0" \
+	"mmcdev=0\0" \
+	"mmcpart=1\0" \
+	"mmcrootfstype=ext4 rootwait fixrtc\0" \
+	"mmcargs=setenv bootargs console=${console} " \
+		"${optargs} " \
+		"root=/dev/mmcblk${mmcdev}p${mmcpart} ro " \
+		"rootfstype=${mmcrootfstype} " \
+		"${cmdline}\0" \
+	"loadimage=load mmc ${bootpart} ${loadaddr} ${bootdir}/${bootfile}\0" \
+	"loadrd=load mmc ${bootpart} ${rdaddr} ${bootdir}/${rdfile};" \
+		"setenv rdsize ${filesize}\0" \
+	"loadfdt=echo loading ${fdt_path} ...;" \
+		"load mmc ${bootpart} ${fdt_addr} ${fdt_path}\0" \
+	"mmcboot=mmc dev ${mmcdev}; " \
+		"if mmc rescan; then " \
+			"echo SD/MMC found on device ${mmcdev};" \
+			"echo Checking for: ${uenv} ...;" \
+			"setenv bootpart ${mmcdev}:${mmcpart};" \
+			"if test -e mmc ${bootpart} ${uenv}; then " \
+				"load mmc ${bootpart} ${loadaddr} ${uenv};" \
+				"env import -t ${loadaddr} ${filesize};" \
+				"echo Loaded environment from ${uenv};" \
+				"if test -n ${dtb}; then " \
+					"setenv fdt_file ${dtb};" \
+					"echo Using: dtb=${fdt_file} ...;" \
+				"fi;" \
+				"echo Checking for uname_r in ${uenv}...;" \
+				"if test -n ${uname_r}; then " \
+					"echo Running uname_boot ...;" \
+					"run uname_boot;" \
+				"fi;" \
+			"fi;" \
+		"fi;\0" \
+	"uname_boot="\
+		"setenv bootdir /boot; " \
+		"setenv bootfile vmlinuz-${uname_r}; " \
+		"setenv ccatfile /boot/ccat.rbf; " \
+		"echo loading CCAT firmware from ${ccatfile}; " \
+		"load mmc ${bootpart} ${loadaddr} ${ccatfile}; " \
+		"fpga load 0 ${loadaddr} ${filesize}; " \
+		"if test -e mmc ${bootpart} ${bootdir}/${bootfile}; then " \
+			"echo loading ${bootdir}/${bootfile} ...; " \
+			"run loadimage;" \
+			"setenv fdt_path /boot/dtbs/${uname_r}/${fdt_file}; " \
+			"if test -e mmc ${bootpart} ${fdt_path}; then " \
+				"run loadfdt;" \
+			"else " \
+				"echo; echo unable to find ${fdt_file} ...;" \
+				"echo booting legacy ...;"\
+				"run mmcargs;" \
+				"echo debug: [${bootargs}] ... ;" \
+				"echo debug: [bootz ${loadaddr}] ... ;" \
+				"bootz ${loadaddr}; " \
+			"fi;" \
+			"run mmcargs;" \
+			"echo debug: [${bootargs}] ... ;" \
+			"echo debug: [bootz ${loadaddr} - ${fdt_addr}] ... ;" \
+			"bootz ${loadaddr} - ${fdt_addr}; " \
+		"fi;\0"
+
+#define CONFIG_BOOTCOMMAND \
+	"run mmcboot;"
+
+#define CONFIG_ARP_TIMEOUT	200UL
+
+/* Miscellaneous configurable options */
+#define CONFIG_SYS_LONGHELP	/* undef to save memory */
+#define CONFIG_AUTO_COMPLETE
+#define CONFIG_SYS_CBSIZE		512	/* Console I/O Buffer Size */
+
+#define CONFIG_SYS_MAXARGS	16	/* max number of command args */
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE	/* Boot Argument Buffer Size */
+
+#define CONFIG_SYS_MEMTEST_START       0x70000000
+#define CONFIG_SYS_MEMTEST_END         0x70010000
+
+#define CONFIG_SYS_LOAD_ADDR		CONFIG_LOADADDR
+
+#define CONFIG_CMDLINE_EDITING
+
+/* Physical Memory Map */
+#define CONFIG_NR_DRAM_BANKS	2
+#define PHYS_SDRAM_1			CSD0_BASE_ADDR
+#define PHYS_SDRAM_1_SIZE		(gd->bd->bi_dram[0].size)
+#define PHYS_SDRAM_2			CSD1_BASE_ADDR
+#define PHYS_SDRAM_2_SIZE		(gd->bd->bi_dram[1].size)
+#define PHYS_SDRAM_SIZE			(gd->ram_size)
+
+#define CONFIG_SYS_SDRAM_BASE		(PHYS_SDRAM_1)
+#define CONFIG_SYS_INIT_RAM_ADDR	(IRAM_BASE_ADDR)
+#define CONFIG_SYS_INIT_RAM_SIZE	(IRAM_SIZE)
+
+#define CONFIG_SYS_INIT_SP_OFFSET \
+	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_ADDR \
+	(CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
+
+/* FLASH and environment organization */
+#define CONFIG_SYS_NO_FLASH
+
+#define CONFIG_ENV_OFFSET      (6 * 64 * 1024)
+#define CONFIG_ENV_SIZE        (8 * 1024)
+#define CONFIG_ENV_IS_IN_MMC
+#define CONFIG_SYS_MMC_ENV_DEV 0
+
+/* Framebuffer and LCD */
+#define CONFIG_PREBOOT
+#define CONFIG_VIDEO_IPUV3
+#define CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE
+#define CONFIG_VIDEO_BMP_RLE8
+#define CONFIG_SPLASH_SCREEN
+#define CONFIG_BMP_16BPP
+#define CONFIG_VIDEO_LOGO
+#define CONFIG_IPUV3_CLK	200000000
+
+#endif /* __CONFIG_H */
diff --git a/include/configs/mx6_common.h b/include/configs/mx6_common.h
index d28654b2ed..e79ec21256 100644
--- a/include/configs/mx6_common.h
+++ b/include/configs/mx6_common.h
@@ -44,7 +44,8 @@
 #define CONFIG_REVISION_TAG
 
 /* Boot options */
-#if (defined(CONFIG_MX6SX) || defined(CONFIG_MX6SL) || defined(CONFIG_MX6UL))
+#if (defined(CONFIG_MX6SX) || defined(CONFIG_MX6SL) || \
+	defined(CONFIG_MX6UL) || defined(CONFIG_MX6SLL))
 #define CONFIG_LOADADDR		0x82000000
 #ifndef CONFIG_SYS_TEXT_BASE
 #define CONFIG_SYS_TEXT_BASE	0x87800000
diff --git a/include/configs/mx6sllevk.h b/include/configs/mx6sllevk.h
new file mode 100644
index 0000000000..b9f25cf0fc
--- /dev/null
+++ b/include/configs/mx6sllevk.h
@@ -0,0 +1,152 @@
+/*
+ * Copyright 2013-2016 Freescale Semiconductor, Inc.
+ *
+ * Configuration settings for the Freescale i.MX6SL EVK board.
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+#include "mx6_common.h"
+
+#ifdef CONFIG_SECURE_BOOT
+#ifndef CONFIG_CSF_SIZE
+#define CONFIG_CSF_SIZE 0x4000
+#endif
+#endif
+
+/* Size of malloc() pool */
+#define CONFIG_SYS_MALLOC_LEN		(16 * SZ_1M)
+
+#define CONFIG_BOARD_EARLY_INIT_F
+#define CONFIG_BOARD_LATE_INIT
+
+#define CONFIG_MXC_UART
+#define CONFIG_MXC_UART_BASE		UART1_BASE
+
+/* I2C Configs */
+#ifdef CONFIG_CMD_I2C
+#define CONFIG_SYS_I2C_MXC
+#define CONFIG_SYS_I2C_MXC_I2C1		/* enable I2C bus 1 */
+#define CONFIG_SYS_I2C_MXC_I2C2		/* enable I2C bus 2 */
+#define CONFIG_SYS_I2C_MXC_I2C3		/* enable I2C bus 3 */
+#define CONFIG_SYS_I2C_SPEED		  100000
+#endif
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+	"epdc_waveform=epdc_splash.bin\0" \
+	"script=boot.scr\0" \
+	"image=zImage\0" \
+	"console=ttymxc0\0" \
+	"fdt_high=0xffffffff\0" \
+	"initrd_high=0xffffffff\0" \
+	"fdt_file=imx6sll-evk.dtb\0" \
+	"fdt_addr=0x83000000\0" \
+	"boot_fdt=try\0" \
+	"ip_dyn=yes\0" \
+	"mmcdev="__stringify(CONFIG_SYS_MMC_ENV_DEV)"\0" \
+	"mmcpart=1\0" \
+	"mmcroot=" CONFIG_MMCROOT " rootwait rw\0" \
+	"mmcautodetect=yes\0" \
+	"mmcargs=setenv bootargs console=${console},${baudrate} " \
+		"root=${mmcroot}\0" \
+	"loadbootscript=" \
+		"fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${script};\0" \
+	"bootscript=echo Running bootscript from mmc ...; " \
+		"source\0" \
+	"loadimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${image}\0" \
+	"loadfdt=fatload mmc ${mmcdev}:${mmcpart} ${fdt_addr} ${fdt_file}\0" \
+	"mmcboot=echo Booting from mmc ...; " \
+		"run mmcargs; " \
+		"if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
+			"if run loadfdt; then " \
+				"bootz ${loadaddr} - ${fdt_addr}; " \
+			"else " \
+				"if test ${boot_fdt} = try; then " \
+					"bootz; " \
+				"else " \
+					"echo WARN: Cannot load the DT; " \
+				"fi; " \
+			"fi; " \
+		"else " \
+			"bootz; " \
+		"fi;\0" \
+	"netargs=setenv bootargs console=${console},${baudrate} " \
+		"root=/dev/nfs " \
+	"ip=dhcp nfsroot=${serverip}:${nfsroot},v3,tcp\0" \
+		"netboot=echo Booting from net ...; " \
+		"usb start; " \
+		"run netargs; " \
+		"if test ${ip_dyn} = yes; then " \
+			"setenv get_cmd dhcp; " \
+		"else " \
+			"setenv get_cmd tftp; " \
+		"fi; " \
+		"${get_cmd} ${image}; " \
+		"if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
+			"if ${get_cmd} ${fdt_addr} ${fdt_file}; then " \
+				"bootz ${loadaddr} - ${fdt_addr}; " \
+			"else " \
+				"if test ${boot_fdt} = try; then " \
+					"bootz; " \
+				"else " \
+					"echo WARN: Cannot load the DT; " \
+				"fi; " \
+			"fi; " \
+		"else " \
+			"bootz; " \
+		"fi;\0"
+
+#define CONFIG_BOOTCOMMAND \
+	   "mmc dev ${mmcdev};" \
+	   "mmc dev ${mmcdev}; if mmc rescan; then " \
+		   "if run loadbootscript; then " \
+			   "run bootscript; " \
+		   "else " \
+			   "if run loadimage; then " \
+				   "run mmcboot; " \
+			   "else run netboot; " \
+			   "fi; " \
+		   "fi; " \
+	   "else run netboot; fi"
+
+/* Miscellaneous configurable options */
+#define CONFIG_SYS_MEMTEST_START	0x80000000
+#define CONFIG_SYS_MEMTEST_END		(CONFIG_SYS_MEMTEST_START + SZ_128M)
+
+#define CONFIG_STACKSIZE		SZ_128K
+
+/* Physical Memory Map */
+#define CONFIG_NR_DRAM_BANKS		1
+#define PHYS_SDRAM			MMDC0_ARB_BASE_ADDR
+#define PHYS_SDRAM_SIZE			SZ_2G
+
+#define CONFIG_SYS_SDRAM_BASE		PHYS_SDRAM
+#define CONFIG_SYS_INIT_RAM_ADDR	IRAM_BASE_ADDR
+#define CONFIG_SYS_INIT_RAM_SIZE	IRAM_SIZE
+
+#define CONFIG_SYS_INIT_SP_OFFSET \
+	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_ADDR \
+	(CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
+
+/* Environment organization */
+#define CONFIG_ENV_SIZE			SZ_8K
+#define CONFIG_SYS_MMC_ENV_PART		0   /* user partition */
+#define CONFIG_MMCROOT			"/dev/mmcblk0p2"  /* USDHC1 */
+
+#define CONFIG_ENV_OFFSET		(12 * SZ_64K)
+#define CONFIG_ENV_IS_IN_MMC
+
+/* MMC Configs */
+#define CONFIG_SYS_FSL_ESDHC_ADDR	USDHC1_BASE_ADDR
+#define CONFIG_SYS_FSL_USDHC_NUM	3
+#define CONFIG_SYS_MMC_ENV_DEV		0   /* USDHC1 */
+
+#define CONFIG_IMX_THERMAL
+
+#define CONFIG_IOMUX_LPSR
+
+#endif				/* __CONFIG_H */
diff --git a/include/configs/udoo_neo.h b/include/configs/udoo_neo.h
index 81e04810eb..aec39db6c1 100644
--- a/include/configs/udoo_neo.h
+++ b/include/configs/udoo_neo.h
@@ -27,13 +27,11 @@
 
 /* Command definition */
 #define CONFIG_MXC_UART_BASE		UART1_BASE
-#define CONFIG_SYS_FSL_USDHC_NUM	2
 #define CONFIG_SYS_MMC_ENV_DEV		0  /*USDHC2*/
 
 /* Linux only */
 #define CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG
 #define CONFIG_EXTRA_ENV_SETTINGS \
-	"console=ttymxc0,115200\0" \
 	"fdt_high=0xffffffff\0" \
 	"initrd_high=0xffffffff\0" \
 	"fdt_file=undefined\0" \
@@ -41,7 +39,6 @@
 	"ip_dyn=yes\0" \
 	"mmcdev=0\0" \
 	"mmcrootfstype=ext4\0" \
-	"mmcautodetect=no\0" \
 	"findfdt="\
 		"if test $board_name = BASIC; then " \
 			"setenv fdt_file imx6sx-udoo-neo-basic.dtb; fi; " \
@@ -61,7 +58,8 @@
 	BOOTENV
 
 #define BOOT_TARGET_DEVICES(func) \
-	func(MMC, mmc, 0)
+	func(MMC, mmc, 0) \
+	func(DHCP, dhcp, na)
 
 #define CONFIG_BOOTCOMMAND \
 	"run findfdt; " \
@@ -91,4 +89,33 @@
 #define CONFIG_ENV_SIZE			SZ_8K
 #define CONFIG_ENV_IS_IN_MMC
 
+#define CONFIG_IMX_THERMAL
+
+/* I2C configs */
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_MXC
+#define CONFIG_SYS_I2C_MXC_I2C1
+#define CONFIG_SYS_I2C_SPEED		100000
+
+/* PMIC */
+#define CONFIG_POWER
+#define CONFIG_POWER_I2C
+#define CONFIG_POWER_PFUZE3000
+#define CONFIG_POWER_PFUZE3000_I2C_ADDR	0x08
+#define PFUZE3000_I2C_BUS	0
+
+/* Network */
+#define CONFIG_FEC_MXC
+#define CONFIG_MII
+
+#define CONFIG_FEC_ENET_DEV 0
+#define IMX_FEC_BASE			ENET_BASE_ADDR
+#define CONFIG_FEC_MXC_PHYADDR          0x0
+
+#define CONFIG_FEC_XCV_TYPE             RMII
+#define CONFIG_ETHPRIME                 "FEC0"
+
+#define CONFIG_PHYLIB
+#define CONFIG_PHY_MICREL
+
 #endif				/* __CONFIG_H */