diff options
| -rw-r--r-- | board/sbc8548/law.c | 8 | ||||
| -rw-r--r-- | board/sbc8548/sbc8548.c | 2 | ||||
| -rw-r--r-- | board/sbc8548/tlb.c | 19 | ||||
| -rw-r--r-- | doc/README.sbc8548 | 34 | ||||
| -rw-r--r-- | include/configs/sbc8548.h | 106 |
5 files changed, 142 insertions, 27 deletions
diff --git a/board/sbc8548/law.c b/board/sbc8548/law.c index febb6829c3..c263191c3d 100644 --- a/board/sbc8548/law.c +++ b/board/sbc8548/law.c @@ -41,13 +41,21 @@ * 0xf8b0_0000 0xf80f_ffff EEPROM 1M * 0xff80_0000 0xffff_ffff FLASH (boot bank) 8M * + * If swapped CS0/CS6 via JP12+SW2.8: + * 0xef80_0000 0xefff_ffff FLASH (2nd bank) 8M + * 0xfc00_0000 0xffff_ffff FLASH (boot bank) 64M + * * Notes: * CCSRBAR and L2-as-SRAM don't need a configured Local Access Window. * If flash is 8M at default position (last 8M), no LAW needed. */ struct law_entry law_table[] = { +#ifdef CONFIG_SYS_ALT_BOOT + SET_LAW(CONFIG_SYS_ALT_FLASH, LAW_SIZE_8M, LAW_TRGT_IF_LBC), +#else SET_LAW(CONFIG_SYS_ALT_FLASH, LAW_SIZE_64M, LAW_TRGT_IF_LBC), +#endif #ifndef CONFIG_SPD_EEPROM SET_LAW(CONFIG_SYS_DDR_SDRAM_BASE, LAW_SIZE_256M, LAW_TRGT_IF_DDR), #endif diff --git a/board/sbc8548/sbc8548.c b/board/sbc8548/sbc8548.c index 26095a5455..63d504d61d 100644 --- a/board/sbc8548/sbc8548.c +++ b/board/sbc8548/sbc8548.c @@ -113,7 +113,7 @@ void lbc_sdram_init(void) puts(" SDRAM: "); - print_size (CONFIG_SYS_LBC_SDRAM_SIZE * 1024 * 1024, "\n"); + print_size(CONFIG_SYS_LBC_SDRAM_SIZE * 1024 * 1024, "\n"); /* * Setup SDRAM Base and Option Registers diff --git a/board/sbc8548/tlb.c b/board/sbc8548/tlb.c index e9cedc7c0d..4bf72147ba 100644 --- a/board/sbc8548/tlb.c +++ b/board/sbc8548/tlb.c @@ -104,6 +104,7 @@ struct fsl_e_tlb_entry tlb_table[] = { MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, 0, 5, BOOKE_PAGESZ_16M, 1), +#ifndef CONFIG_SYS_ALT_BOOT /* * TLB 6: 64M Non-cacheable, guarded * 0xec000000 64M 64MB user FLASH @@ -111,6 +112,24 @@ struct fsl_e_tlb_entry tlb_table[] = { SET_TLB_ENTRY(1, CONFIG_SYS_ALT_FLASH, CONFIG_SYS_ALT_FLASH, MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, 0, 6, BOOKE_PAGESZ_64M, 1), +#else + /* + * TLB 6: 4M Non-cacheable, guarded + * 0xef800000 4M 1st 1/2 8MB soldered FLASH + */ + SET_TLB_ENTRY(1, CONFIG_SYS_ALT_FLASH, CONFIG_SYS_ALT_FLASH, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 6, BOOKE_PAGESZ_4M, 1), + + /* + * TLB 7: 4M Non-cacheable, guarded + * 0xefc00000 4M 2nd half 8MB soldered FLASH + */ + SET_TLB_ENTRY(1, CONFIG_SYS_ALT_FLASH + 0x400000, + CONFIG_SYS_ALT_FLASH + 0x400000, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 7, BOOKE_PAGESZ_4M, 1), +#endif }; diff --git a/doc/README.sbc8548 b/doc/README.sbc8548 index 5fa9c93685..e6b8abe2b3 100644 --- a/doc/README.sbc8548 +++ b/doc/README.sbc8548 @@ -86,6 +86,33 @@ The "md" steps in the above are just a precautionary step that allow you to confirm the u-boot version that was downloaded, and then confirm that it was copied to flash. +The above assumes that you are using the default board settings which +have u-boot in the 8MB flash, tied to /CS0. + +If you are running the default 8MB /CS0 settings but want to store an +image in the SODIMM that is built with CONFIG_SYS_ALT_BOOT enabled, +(as a backup, etc) then the steps will become: + + tftp u-boot.bin + md 200000 10 + protect off all + era eff00000 efffffff + cp.b 200000 eff00000 100000 + md eff00000 10 + protect on all + +Finally, if you are running the alternate 64MB /CS0 settings and want +to update the in-use u-boot image, then (again with CONFIG_SYS_ALT_BOOT +enabled) the steps will become: + + tftp u-boot.bin + md 200000 10 + protect off all + era fff00000 ffffffff + cp.b 200000 fff00000 100000 + md fff00000 10 + protect on all + Hardware Reference: =================== @@ -127,10 +154,9 @@ JP19 PCI mode PCI PCI-X onto /CS0 and the SODIMM flash on /CS6 (default). When JP12 is jumpered parallel to the LBC-SDRAM, then /CS0 is for the SODIMM flash and /CS6 is for the boot flash. Note that in this -alternate setting, you also need to switch SW2.8 to ON. Currently -u-boot doesn't support booting off the SODIMM in this alternate -setting without manually altering BR0/OR0 and BR6/OR6 in the -board config file appropriately. +alternate setting, you also need to switch SW2.8 to ON. +See the setting CONFIG_SYS_ALT_BOOT if you want to use this setting +and boot u-boot from the 64MB SODIMM Switches: diff --git a/include/configs/sbc8548.h b/include/configs/sbc8548.h index cea017900f..fb07d09f3f 100644 --- a/include/configs/sbc8548.h +++ b/include/configs/sbc8548.h @@ -57,9 +57,19 @@ #define CONFIG_MPC8548 1 /* MPC8548 specific */ #define CONFIG_SBC8548 1 /* SBC8548 board specific */ +/* + * If you want to boot from the SODIMM flash, instead of the soldered + * on flash, set this, and change JP12, SW2:8 accordingly. + */ +#undef CONFIG_SYS_ALT_BOOT + #ifndef CONFIG_SYS_TEXT_BASE +#ifdef CONFIG_SYS_ALT_BOOT +#define CONFIG_SYS_TEXT_BASE 0xfff00000 +#else #define CONFIG_SYS_TEXT_BASE 0xfffa0000 #endif +#endif #undef CONFIG_RIO @@ -139,28 +149,54 @@ /* * FLASH on the Local Bus * Two banks, one 8MB the other 64MB, using the CFI driver. - * Boot from BR0/OR0 bank at 0xff80_0000 - * Alternate BR6/OR6 bank at 0xec00_0000 + * JP12+SW2.8 are used to swap CS0 and CS6, defaults are to have + * CS0 the 8MB boot flash, and CS6 the 64MB flash. * - * BR0: + * Default: + * ec00_0000 efff_ffff 64MB SODIMM + * ff80_0000 ffff_ffff 8MB soldered flash + * + * Alternate: + * ef80_0000 efff_ffff 8MB soldered flash + * fc00_0000 ffff_ffff 64MB SODIMM + * + * BR0_8M: * Base address 0 = 0xff80_0000 = BR0[0:16] = 1111 1111 1000 0000 0 * Port Size = 8 bits = BRx[19:20] = 01 * Use GPCM = BRx[24:26] = 000 * Valid = BRx[31] = 1 * - * 0 4 8 12 16 20 24 28 - * 1111 1111 1000 0000 0000 1000 0000 0001 = ff800801 BR0 - * - * BR6: - * Base address 6 = 0xec00_0000 = BR6[0:16] = 1110 1100 0000 0000 0 + * BR0_64M: + * Base address 0 = 0xfc00_0000 = BR0[0:16] = 1111 1100 0000 0000 0 * Port Size = 32 bits = BRx[19:20] = 11 + * + * 0 4 8 12 16 20 24 28 + * 1111 1111 1000 0000 0000 1000 0000 0001 = ff800801 BR0_8M + * 1111 1100 0000 0000 0001 1000 0000 0001 = fc001801 BR0_64M + */ +#define CONFIG_SYS_BR0_8M 0xff800801 +#define CONFIG_SYS_BR0_64M 0xfc001801 + +/* + * BR6_8M: + * Base address 6 = 0xef80_0000 = BR6[0:16] = 1110 1111 1000 0000 0 + * Port Size = 8 bits = BRx[19:20] = 01 * Use GPCM = BRx[24:26] = 000 * Valid = BRx[31] = 1 + + * BR6_64M: + * Base address 6 = 0xec00_0000 = BR6[0:16] = 1110 1100 0000 0000 0 + * Port Size = 32 bits = BRx[19:20] = 11 * * 0 4 8 12 16 20 24 28 - * 1110 1100 0000 0000 0001 1000 0000 0001 = ec001801 BR6 - * - * OR0: + * 1110 1111 1000 0000 0000 1000 0000 0001 = ef800801 BR6_8M + * 1110 1100 0000 0000 0001 1000 0000 0001 = ec001801 BR6_64M + */ +#define CONFIG_SYS_BR6_8M 0xef800801 +#define CONFIG_SYS_BR6_64M 0xec001801 + +/* + * OR0_8M: * Addr Mask = 8M = OR1[0:16] = 1111 1111 1000 0000 0 * XAM = OR0[17:18] = 11 * CSNT = OR0[20] = 1 @@ -169,11 +205,20 @@ * TRLX = use relaxed timing = OR0[29] = 1 * EAD = use external address latch delay = OR0[31] = 1 * - * 0 4 8 12 16 20 24 28 - * 1111 1111 1000 0000 0110 1110 0110 0101 = ff806e65 OR0 + * OR0_64M: + * Addr Mask = 64M = OR1[0:16] = 1111 1100 0000 0000 0 * - * OR6: - * Addr Mask = 64M = OR6[0:16] = 1111 1100 0000 0000 0 + * + * 0 4 8 12 16 20 24 28 + * 1111 1111 1000 0000 0110 1110 0110 0101 = ff806e65 OR0_8M + * 1111 1100 0000 0000 0110 1110 0110 0101 = fc006e65 OR0_64M + */ +#define CONFIG_SYS_OR0_8M 0xff806e65 +#define CONFIG_SYS_OR0_64M 0xfc006e65 + +/* + * OR6_8M: + * Addr Mask = 8M = OR6[0:16] = 1111 1111 1000 0000 0 * XAM = OR6[17:18] = 11 * CSNT = OR6[20] = 1 * ACS = half cycle delay = OR6[21:22] = 11 @@ -181,20 +226,37 @@ * TRLX = use relaxed timing = OR6[29] = 1 * EAD = use external address latch delay = OR6[31] = 1 * + * OR6_64M: + * Addr Mask = 64M = OR6[0:16] = 1111 1100 0000 0000 0 + * * 0 4 8 12 16 20 24 28 - * 1111 1100 0000 0000 0110 1110 0110 0101 = fc006e65 OR6 + * 1111 1111 1000 0000 0110 1110 0110 0101 = ff806e65 OR6_8M + * 1111 1100 0000 0000 0110 1110 0110 0101 = fc006e65 OR6_64M */ +#define CONFIG_SYS_OR6_8M 0xff806e65 +#define CONFIG_SYS_OR6_64M 0xfc006e65 +#ifndef CONFIG_SYS_ALT_BOOT /* JP12 in default position */ #define CONFIG_SYS_BOOT_BLOCK 0xff800000 /* start of 8MB Flash */ #define CONFIG_SYS_ALT_FLASH 0xec000000 /* 64MB "user" flash */ -#define CONFIG_SYS_FLASH_BASE CONFIG_SYS_BOOT_BLOCK /* start of FLASH 16M */ -#define CONFIG_SYS_BR0_PRELIM 0xff800801 -#define CONFIG_SYS_BR6_PRELIM 0xec001801 +#define CONFIG_SYS_BR0_PRELIM CONFIG_SYS_BR0_8M +#define CONFIG_SYS_OR0_PRELIM CONFIG_SYS_OR0_8M + +#define CONFIG_SYS_BR6_PRELIM CONFIG_SYS_BR6_64M +#define CONFIG_SYS_OR6_PRELIM CONFIG_SYS_OR6_64M +#else /* JP12 in alternate position */ +#define CONFIG_SYS_BOOT_BLOCK 0xfc000000 /* start 64MB Flash */ +#define CONFIG_SYS_ALT_FLASH 0xef800000 /* 8MB soldered flash */ -#define CONFIG_SYS_OR0_PRELIM 0xff806e65 -#define CONFIG_SYS_OR6_PRELIM 0xfc006e65 +#define CONFIG_SYS_BR0_PRELIM CONFIG_SYS_BR0_64M +#define CONFIG_SYS_OR0_PRELIM CONFIG_SYS_OR0_64M + +#define CONFIG_SYS_BR6_PRELIM CONFIG_SYS_BR6_8M +#define CONFIG_SYS_OR6_PRELIM CONFIG_SYS_OR6_8M +#endif +#define CONFIG_SYS_FLASH_BASE CONFIG_SYS_BOOT_BLOCK #define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE, \ CONFIG_SYS_ALT_FLASH} #define CONFIG_SYS_MAX_FLASH_BANKS 2 /* number of banks */ @@ -330,7 +392,7 @@ * thing for MONITOR_LEN in both cases. */ #define CONFIG_SYS_MONITOR_LEN (~CONFIG_SYS_TEXT_BASE + 1) -#define CONFIG_SYS_MALLOC_LEN (128 * 1024) /* Reserved for malloc */ +#define CONFIG_SYS_MALLOC_LEN (1024 * 1024) /* Reserved for malloc */ /* Serial Port */ #define CONFIG_CONS_INDEX 1 |