diff options
Diffstat (limited to 'arch/arm/dts/bcm2837-rpi-3-b.dts')
| -rw-r--r-- | arch/arm/dts/bcm2837-rpi-3-b.dts | 128 |
1 files changed, 125 insertions, 3 deletions
diff --git a/arch/arm/dts/bcm2837-rpi-3-b.dts b/arch/arm/dts/bcm2837-rpi-3-b.dts index 20725ca487..ce71f578c5 100644 --- a/arch/arm/dts/bcm2837-rpi-3-b.dts +++ b/arch/arm/dts/bcm2837-rpi-3-b.dts @@ -1,6 +1,7 @@ +// SPDX-License-Identifier: GPL-2.0 /dts-v1/; #include "bcm2837.dtsi" -#include "bcm2835-rpi.dtsi" +#include "bcm2836-rpi.dtsi" #include "bcm283x-rpi-smsc9514.dtsi" #include "bcm283x-rpi-usb-host.dtsi" @@ -8,15 +9,122 @@ compatible = "raspberrypi,3-model-b", "brcm,bcm2837"; model = "Raspberry Pi 3 Model B"; - memory { + chosen { + /* 8250 auxiliary UART instead of pl011 */ + stdout-path = "serial1:115200n8"; + }; + + memory@0 { reg = <0 0x40000000>; }; leds { act { - gpios = <&gpio 47 0>; + gpios = <&expgpio 2 GPIO_ACTIVE_HIGH>; }; }; + + wifi_pwrseq: wifi-pwrseq { + compatible = "mmc-pwrseq-simple"; + reset-gpios = <&expgpio 1 GPIO_ACTIVE_LOW>; + }; +}; + +&firmware { + expgpio: gpio { + compatible = "raspberrypi,firmware-gpio"; + gpio-controller; + #gpio-cells = <2>; + gpio-line-names = "BT_ON", + "WL_ON", + "STATUS_LED", + "LAN_RUN", + "HDMI_HPD_N", + "CAM_GPIO0", + "CAM_GPIO1", + "PWR_LOW_N"; + status = "okay"; + }; +}; + +&gpio { + /* + * Taken from rpi_SCH_3b_1p2_reduced.pdf and + * the official GPU firmware DT blob. + * + * Legend: + * "NC" = not connected (no rail from the SoC) + * "FOO" = GPIO line named "FOO" on the schematic + * "FOO_N" = GPIO line named "FOO" on schematic, active low + */ + gpio-line-names = "ID_SDA", + "ID_SCL", + "SDA1", + "SCL1", + "GPIO_GCLK", + "GPIO5", + "GPIO6", + "SPI_CE1_N", + "SPI_CE0_N", + "SPI_MISO", + "SPI_MOSI", + "SPI_SCLK", + "GPIO12", + "GPIO13", + /* Serial port */ + "TXD1", + "RXD1", + "GPIO16", + "GPIO17", + "GPIO18", + "GPIO19", + "GPIO20", + "GPIO21", + "GPIO22", + "GPIO23", + "GPIO24", + "GPIO25", + "GPIO26", + "GPIO27", + "", /* GPIO 28 */ + "LAN_RUN_BOOT", + /* Used by BT module */ + "CTS0", + "RTS0", + "TXD0", + "RXD0", + /* Used by Wifi */ + "SD1_CLK", + "SD1_CMD", + "SD1_DATA0", + "SD1_DATA1", + "SD1_DATA2", + "SD1_DATA3", + "PWM0_OUT", + "PWM1_OUT", + "ETHCLK", + "WIFI_CLK", + "SDA0", + "SCL0", + "SMPS_SCL", + "SMPS_SDA", + /* Used by SD Card */ + "SD_CLK_R", + "SD_CMD_R", + "SD_DATA0_R", + "SD_DATA1_R", + "SD_DATA2_R", + "SD_DATA3_R"; +}; + +&pwm { + pinctrl-names = "default"; + pinctrl-0 = <&pwm0_gpio40 &pwm1_gpio41>; + status = "okay"; +}; + +&hdmi { + hpd-gpios = <&expgpio 4 GPIO_ACTIVE_LOW>; }; /* uart0 communicates with the BT module */ @@ -24,6 +132,12 @@ pinctrl-names = "default"; pinctrl-0 = <&uart0_gpio32 &gpclk2_gpio43>; status = "okay"; + + bluetooth { + compatible = "brcm,bcm43438-bt"; + max-speed = <2000000>; + shutdown-gpios = <&expgpio 0 GPIO_ACTIVE_HIGH>; + }; }; /* uart1 is mapped to the pin header */ @@ -35,11 +149,19 @@ /* SDHCI is used to control the SDIO for wireless */ &sdhci { + #address-cells = <1>; + #size-cells = <0>; pinctrl-names = "default"; pinctrl-0 = <&emmc_gpio34>; status = "okay"; bus-width = <4>; non-removable; + mmc-pwrseq = <&wifi_pwrseq>; + + brcmf: wifi@1 { + reg = <1>; + compatible = "brcm,bcm4329-fmac"; + }; }; /* SDHOST is used to drive the SD card */ |