summaryrefslogtreecommitdiff
path: root/drivers
AgeCommit message (Collapse)Author
2013-07-19LogicPD Support for OMAP3/DM3/AM3 boards 2.4 Update Release 22011.06-omap3logic-ts4Justin Waters
2013-05-14LogicPD Support for OMAP3/DM3/AM3 boards 2.4 UpdateJustin Waters
2013-04-24LogicPD Support for OMAP3/DM3/AM3 boards 2.3 UpdateJustin Waters
2013-04-24LogicPD Support for OMAP3/DM3/AM3 boards 2.2 UpdateJustin Waters
2013-04-24LogicPD Support for OMAP3/DM3/AM3 boards 2.1 UpdateJustin Waters
2012-04-17LogicPD Support for OMAP3/DM3/AM3 boardsJustin Waters
From Logic BSP-2.0-5-01
2011-06-25usb: convert to partial linkingMike Frysinger
Looks like this was missed during the conversion to partial linking. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2011-06-25ehci-pci: Fix PCI EHCI driver for 36-bitZhao Chenhui
Convert the PCI base address into a virtual address. Signed-off-by: Zhao Chenhui <b35336@freescale.com> Signed-off-by: Li Yang <leoli@freescale.com>
2011-06-25musb: process control messages after roothub accepted itCliff Cai
When dealing with non-multipoint devices, if the software root hub code accepted the message, then we still need to process it normally. So only return quickly when the root hub skipped the message or is otherwise in an error state. Signed-off-by: Cliff Cai <cliff.cai@analog.com> Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2011-06-23Merge branch 'master' of git://git.denx.de/u-boot-armWolfgang Denk
* 'master' of git://git.denx.de/u-boot-arm: run arm_pci_init after relocation IXP42x PCI rewrite update/fix PDNB3 board update/fix IXDP425 / IXDPG425 boards add dvlhost (dLAN 200 AV Wireless G) board IXP NPE: add support for fixed-speed MII ports update/fix AcTux4 board update/fix AcTux3 board update/fix AcTux2 board update/fix AcTux1 board use -ffunction-sections / --gc-sections on IXP42x support CONFIG_SYS_LDSCRIPT on ARM fix "depend" target in npe directory Fix IXP code to work after relocation was added trigger hardware watchdog in IXP42x serial driver add support for IXP42x Rev. B1 and newer add XScale sub architecture (IXP/PXA) to maintainer list Conflicts: arch/arm/lib/board.c Signed-off-by: Wolfgang Denk <wd@denx.de>
2011-06-23IXP42x PCI rewriteMichael Schwingen
clean up IXP PCI handling: get rid of IXP-private bus scan, BAR assign etc. code and use u-boot's PCI infrastructure instead. Move board-specific PCI setup code (clock/reset) to board directory. Signed-off-by: Michael Schwingen <michael@schwingen.org>
2011-06-23trigger hardware watchdog in IXP42x serial driverMichael Schwingen
Signed-off-by: Michael Schwingen <michael@schwingen.org>
2011-06-22ARM: drop unsupported 'trab' boardWolfgang Denk
The 'trab' board configuration is broken, and there is nobody who is interested and willing to fix it. Drop it. This includes support for VFD displays which have always been used by this board only. Signed-off-by: Wolfgang Denk <wd@denx.de>
2011-06-21macb: fix compile warningandreas.devel@googlemail.com
This patch fixes following compile warning: ---8<--- macb.c: In function 'macb_write_hwaddr': macb.c:525:2: warning: dereferencing type-punned pointer will break strict-aliasing rules --->8--- Signed-off-by: Andreas Bießmann <andreas.devel@gmail.com>
2011-06-21at91_emac: fix compile warningandreas.devel@googlemail.com
This patch removes the warning ---8<--- at91_emac.c: In function 'at91emac_write_hwaddr': at91_emac.c:487:2: warning: dereferencing type-punned pointer will break strict-aliasing rules --->8--- Signed-off-by: Andreas Bießmann <andreas.devel@gmail.com>
2011-06-21ATMEL spi_dataflash driver - fix to build againReinhard Meyer
The rework effort for ATMEL (AT91/AVR32) accidentially broke build of this driver. Fix this to make it build again. However this driver should be reworked as soon as possible! Signed-off-by: Reinhard Meyer <u-boot@emk-elektronik.de>
2011-06-21update arm/at91rm9200 work with rework rework110202Jens Scharsig
* convert at91rm9200ek and eb_cpux9k2 board to ATMEL_xxx name scheme * Fix: timer.c compile error io.h not found with arm/at91rm9200 * update arm920t/at91 to ATMEL_xxx name scheme * update arm920t/at91 soc lib * update at91_emac driver Signed-off-by: Jens Scharsig <js_at_ng@scharsoft.de> Tested-by: Andreas Bießmann <andreas.devel@gmail.com>
2011-06-21mxc_spi.c: typo fixedHelmut Raiger
Signed-off-by: Helmut Raiger <helmut.raiger@hale.at>
2011-06-01sf: kick watchdog when pollingPatrick Sestier
The status polling can take a while, so make sure we kick the watchdog after each successful poll. Signed-off-by: Patrick Sestier <psestier@mircom.com> Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2011-06-01I2C: Add driver for ST-Ericsson U8500 i2cMichael Brandt
Signed-off-by: John Rigby <john.rigby@linaro.org> CC: Heiko Schocher <hs@denx.de>
2011-05-31mvgbe: enable configurability of PORT_SERIAL_CONTROL_VALUEValentin Longchamp
This allows this configuration to be defined differently for some boards that request it. Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com> cc: Holger Brunck <holger.brunck@keymile.com> cc: Heiko Schocher <hs@denx.de> cc: Wolfgang Denk <wd@denx.de> cc: Detlev Zundel <dzu@denx.de> cc: Prafulla Wadaskar <prafulla@marvell.com>
2011-05-26S5P: add set_mmc_clk for external clock controlJaehoon Chung
This patch added set_mmc_clk for external clock control. c210 didn't support host clock control. So We need external_clock_control function for c210. Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
2011-05-26MMC S5P: Fix typoDirk Behme
Fix typo resulting in the compilation error s5p_mmc.c: In function 's5p_mmc_initialize': s5p_mmc.c:469: error: 'struct mmc' has no member named 'm_bmax' introduced by commit "MMC: make b_max unconditional" (8feafcc49c0b7a9c541904f95a43dbef2fecc38b) Signed-off-by: Dirk Behme <dirk.behme@googlemail.com> CC: John Rigby <john.rigby@linaro.org> CC: Andy Fleming <afleming@freescale.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2011-05-23mvsata: issue hard reset on initializationMichael Walle
Before the actual initialization do a hard reset of the SATA port and the connected device. changes v1->v2: - add comment for udelay Signed-off-by: Michael Walle <michael@walle.cc> Cc: Prafulla Wadaskar <prafulla@marvell.com> Cc: Albert Aribaud <albert.u.boot@aribaud.net>
2011-05-19Minor coding style cleanup.Wolfgang Denk
Signed-off-by: Wolfgang Denk <wd@denx.de>
2011-05-18MMC: omap_hsmmc.c: Add missing prototype headerDirk Behme
Add missing header file to fix compilation warning omap_hsmmc.c: In function 'omap_mmc_init': omap_hsmmc.c:474: warning: implicit declaration of function 'get_cpu_family' omap_hsmmc.c:474: warning: implicit declaration of function 'get_cpu_rev' introduced by commit "MMC: omap_hsmmc.c: disable multiblock rw on old rev omap34xx silicon" (4ca9244d74f146a0605f5bee28a66e39aae88d3e) Signed-off-by: Dirk Behme <dirk.behme@googlemail.com> CC: Andy Fleming <afleming@freescale.com> CC: John Rigby <john.rigby@linaro.org>
2011-05-18fsl_esdhc: Initialize mmc->b_maxFabio Estevam
commit 262951(MMC: make b_max unconditional) missed to update fsl_esdhc. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: Stefano Babic <sbabic@denx.de>
2011-05-18mmc: enable partition switch function for emmcLei Wen
For emmc, it may have up to 7 partitions: two boot partitions, one user partition, one RPMB partition and four general purpose partitions. (Refer to JESD84-A44.pdf/page 154) As bootloader may need to read out or reflashing images on those different partitions, it is better to enable the partition switch with console command support. Also for partition would be restore to user partition(part 0) when CMD0 is used, so change mmc_init routine to perform normal initialization only once for each slot, unless use the rescan command to force init again. Signed-off-by: Lei Wen <leiwen@marvell.com> Acked-by: Andy Fleming <afleming@freescale.com>
2011-05-18cmd_mmc: eliminate device num in the mmc commandLei Wen
mmc command applied device, like ide and usb... Signed-off-by: Lei Wen <leiwen@marvell.com> Acked-by: Andy Fleming <afleming@freescale.com>
2011-05-18mmc_spi: generate response for send status commandThomas Chou
A "send status" command is added with the commit "mmc: checking status after commands with R1b response". But the status register returned from send status command of SPI protocol is different from that of MMC/SD protocol. We do a simple test and generate a response in stead of full bit-by-bit translation. Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
2011-05-18AT91: fix at91sam_wdt.c to reworked header filesReinhard Meyer
Signed-off-by: Reinhard Meyer <u-boot@emk-elektronik.de>
2011-05-18ATMEL: fix dataflash (dirty) this file should be converted to struct SoC accessReinhard Meyer
Signed-off-by: Reinhard Meyer <u-boot@emk-elektronik.de>
2011-05-18AT91: change includes from asm/arch/io.h to asm/io.hReinhard Meyer
and remove the now unused asm/arch-at91/io.h Signed-off-by: Reinhard Meyer <u-boot@emk-elektronik.de>
2011-05-18ATMEL: fix related common atmel driver filesReinhard Meyer
Signed-off-by: Reinhard Meyer <u-boot@emk-elektronik.de>
2011-05-18AT91: fix related at91 driver filesReinhard Meyer
Signed-off-by: Reinhard Meyer <u-boot@emk-elektronik.de>
2011-05-18avr32: fixup definitions to ATMEL_BASE_xxxAndreas Bießmann
Signed-off-by: Andreas Bießmann <biessmann@corscience.de>
2011-05-18avr32: rename memory-map.h -> hardware.hAndreas Bießmann
Signed-off-by: Andreas Bießmann <biessmann@corscience.de>
2011-05-12ftsmc020: fix relocationMacpaul Lin
Avoid relocation problem by fix global declaration. Signed-off-by: Macpaul Lin <macpaul@andestech.com>
2011-05-12ftide020: add faraday ide ahb controllerMacpaul Lin
Faraday's ftide020_s is an IDE-AHB controller for SoC design. This patch add the u-boot driver (PIO) of ftide020 ATA (IDE) driver. IDE commands include read, info, and other functions has been implemented. Because this IDE controller support AHB interface only which is differ from other most IDE controller supports PCI interface. Some registers access is required during CMD/DATA I/O. Hence a configuration "CONFIG_IDE_AHB" is required to be defined according to the feature in cmd_ide.c. Signed-off-by: Macpaul Lin <macpaul@andestech.com>
2011-05-12hwmon: Extend lm63.c to support LM64Dirk Eibach
This patch adds support for the National LM64 temperature sensor with integrated fan control to lm63.c. Main difference between LM63 and LM64 is 16°C offset in sensor readings. Signed-off-by: Dirk Eibach <eibach@gdsys.de>
2011-05-12net: xilinx emaclite: Fix return valuesMichal Simek
Fix return values for initialize/init/recv/send functions Signed-off-by: Michal Simek <monstr@monstr.eu>
2011-05-12NET: pass source IP address to packet handlersLuca Ceresoli
This is needed for the upcoming TFTP server implementation. This also simplifies PingHandler() and fixes rxhand_f documentation. Signed-off-by: Luca Ceresoli <luca.ceresoli@comelit.it> Cc: Wolfgang Denk <wd@denx.de> Acked-by: Detlev Zundel <dzu@denx.de>
2011-05-12Merge branch 'master' of git://git.denx.de/u-boot-armWolfgang Denk
2011-05-12Serial: p1011: new vendor init optionsJohn Rigby
Two new options: CONFIG_PL011_SERIAL_RLCR Some vendor versions of PL011 serial ports (e.g. ST-Ericsson U8500) have separate receive and transmit line control registers. Set this variable to initialize the extra register. CONFIG_PL011_SERIAL_FLUSH_ON_INIT On some platforms (e.g. U8500) U-Boot is loaded by a second stage boot loader that has already initialized the UART. Define this variable to flush the UART at init time. empty fifo on init Signed-off-by: John Rigby <john.rigby@linaro.org> Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
2011-05-11gpio: imx: Fix return value on errorFabio Estevam
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2011-04-30Merge branch 'master' of git://git.denx.de/u-boot-mpc85xxWolfgang Denk
2011-04-30spi: add new driver for OpenCores tiny_spiThomas Chou
This patch adds support for OpenCores tiny_spi. http://opencores.org/project,tiny_spi Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
2011-04-29Merge branch 'master' of git://git.denx.de/u-boot-mmcWolfgang Denk
2011-04-29powerpc: eSPI and eSPI controller supportMingkai Hu
Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com> Singed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com> Signed-off-by: Shaohui Xie <b21989@freescale.com> Cc: Mike Frysinger <vapier@gentoo.org> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-04-29fsl_esdhc: Fix multi-block read restriction on i.MX53 eSDHCv2Jason Liu
For freescale i.MX53 eSDHCv2, when using CMD12, cmdtype need to be set to ABORT, otherwise, next read command will hang. This is a software Software Restrictions in i.MX53 reference manual: 29.7.8 Multi-block Read For pre-defined multi-block read operation, that is,the number of blocks to read has been defined by previous CMD23 for MMC, or pre-defined number of blocks in CMD53 for SDIO/SDCombo,or whatever multi-block read without abort command at card side, an abort command, either automatic or manual CMD12/CMD52, is still required by ESDHC after the pre-defined number of blocks are done, to drive the internal state machine to idle mode. In this case, the card may not respond to this extra abort command and ESDHC will get Response Timeout. It is recommended to manually send an abort command with RSPTYP[1:0] both bits cleared. Signed-off-by: Jason Liu <jason.hui@linaro.org>
generated by cgit v1.2.3 (git 2.0.4) at 2024-06-20 23:35:34 +0000