summaryrefslogtreecommitdiff
path: root/include/configs/db-88f6820-gp.h
AgeCommit message (Collapse)Author
2016-01-14arm: mvebu: Move SoC selection (A38X vs AXP) into KconfigStefan Roese
Until now, the SoC selection for the ARCH_MVEBU platforms has been done in the config header. Using CONFIG_ARMADA_XP in a non-clear way. As it needed to get selected for AXP and A38x based boards. This patch now changes this to move the SoC selection to Kconfig. And also uses CONFIG_ARCH_MVEBU as a common define for both AXP and A38x. This makes things a bit clearer - especially for new board additions. Additionally the defines CONFIG_SYS_MVEBU_DDR_AXP and CONFIG_SYS_MVEBU_DDR_A38X are replaced with the already available CONFIG_ARMADA_38X and CONFIG_ARMADA_XP. And CONFIG_DDR3 is removed, as its not referenced anywhere. Signed-off-by: Stefan Roese <sr@denx.de> Cc: Luka Perkov <luka.perkov@sartura.hr>
2016-01-14arm: mvebu: Move some defines to common include fileStefan Roese
This patch moves some config options to the mvebu common include file. Making it easier to not forget these defines for new boards. Signed-off-by: Stefan Roese <sr@denx.de> Cc: Luka Perkov <luka.perkov@sartura.hr> Cc: Dirk Eibach <dirk.eibach@gdsys.cc>
2016-01-14net: mvneta: Convert to driver modelStefan Roese
Update this driver to support driver model. As all MVEBU boards using this driver are converted with this patch, the non-driver-model code can be removed completely. This is also the reason why this patch is quite big and includes a) the driver change and b) the platform change. As its not git-bisect save otherwise. With this conversion, some parameters are now extracted from the DT instread of using the config header defines. The supported properties right now are: PHY-mode ("phy-mode") and PHY-address ("reg"). The base addresses for the ethernet controllers can be removed from the header files as well. Please note that this patch also removes the E1000 network driver from some MVEBU config headers. This is necessary, as with DM_ETH configured and the e1000 driver enabled, the PCI driver also needs to support DM. But the MVEBU PCI(e) driver still needs to get ported to DM. When this is done, the E1000 driver can be enabled again. Signed-off-by: Stefan Roese <sr@denx.de> Cc: Luka Perkov <luka.perkov@sartura.hr> Cc: Dirk Eibach <dirk.eibach@gdsys.cc> Cc: Joe Hershberger <joe.hershberger@ni.com> Cc: Simon Glass <sjg@chromium.org>
2016-01-14arm: mvebu: Add SPI driver model supportStefan Roese
This patch enables the DM support for the SPI driver and the SPI NOR flash chips. Some MVEBU boards boot from SPI NOR, so adding the aliases and enabling CONFIG_DM_SEQ_ALIAS is needed here. Signed-off-by: Stefan Roese <sr@denx.de> Cc: Luka Perkov <luka.perkov@sartura.hr> Cc: Dirk Eibach <dirk.eibach@gdsys.cc> Cc: Simon Glass <sjg@chromium.org>
2016-01-14arm: mvebu: Add DM and OF_CONTROL support to SPLStefan Roese
This patch adds full DM support to the SPL on MVEBU. Currently only serial is supported. Other drivers will follow. This patch also adds the necessary config values for the DEBUG UART to the MVEBU defconfig files. This came in handy while implementing this DM support. Additionally, the mvebu specific SPL linker script is removed and this common one is used instead: arch/arm/cpu/u-boot-spl.lds This common linker script already handles all special cases. No need to reinvent the wheel for MVEBU here. Signed-off-by: Stefan Roese <sr@denx.de> Cc: Luka Perkov <luka.perkov@sartura.hr> Cc: Dirk Eibach <dirk.eibach@gdsys.cc> Cc: Simon Glass <sjg@chromium.org>
2015-11-25sf: Move SPI flash drivers to defconfigBin Meng
There are already Kconfig options for SPI flash drivers, but we have not moved them from config.h to defconfig files. This commit does this in a batch. Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
2015-10-24arm, powerpc: select SYS_GENERIC_BOARDMasahiro Yamada
We have finished Generic Board conversion for ARM and PowerPC, i.e. all the boards have been converted except OpenRISC, SuperH, SPARC, which have not supported Generic Board framework yet. Select SYS_GENERIC_BOARD in arch/Kconfig and delete all the macro defines in include/configs/*.h. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2015-10-21arm: mvebu: Enable DM_USB on AXP / A38x boardsStefan Roese
This patch enables DM_USB on the Marvell AXP / A38x eval boards. Signed-off-by: Stefan Roese <sr@denx.de> Cc: Simon Glass <sjg@chromium.org> Cc: Luka Perkov <luka.perkov@sartura.hr>
2015-10-21arm: mvebu: Only set CONFIG_SKIP_LOWLEVEL_INIT for SPLStefan Roese
When running on the AXP I sometimes noticed a strange behavior. As some characters are not echoed on the U-Boot prompt. Not disabling the lowlevel_init code, especially calling cpu_init_cp15() in the main U-Boot seems to solve this issue. Signed-off-by: Stefan Roese <sr@denx.de>
2015-08-17arm: mvebu: db-88f6820-gp: Enable PCI supportStefan Roese
This patch enabled the MVEBU PCIe support on the db-88f6820-gp A38x eval board. It also enabled the Intel E1000 driver support and adds the initialization of PCIe network controllers to the board code. Signed-off-by: Stefan Roese <sr@denx.de> Cc: Anton Schubert <anton.schubert@gmx.de> Cc: Luka Perkov <luka.perkov@sartura.hr> Cc: Dirk Eibach <eibach@gdsys.de>
2015-08-17arm: mvebu: Move CONFIG_SYS_TEXT_BASE to an address < 16 MiBStefan Roese
This patch moves CONFIG_SYS_TEXT_BASE to 0x00800000 for all Armada XP / 38x boards in mainline U-Boot. This is done in preparation for the ECC SDRAM scrubbing that needs to be done in the main U-Boot. The SPL (previously bin_hdr) has already scrubbed the area: 0x0000.0000 - 0x0100.0000 In this area this main U-Boot needs to get loaded. The main U-Boot then can scrub the remaining SDRAM area while running from this location. Signed-off-by: Stefan Roese <sr@denx.de> Cc: Luka Perkov <luka.perkov@sartura.hr>
2015-07-24arm: mvebu: db-88f6820-gp: Add SDIO/MMC SPL boot supportStefan Roese
This patch adds the configuration options to boot via SDIO/MMC on the Marvell DB-88F6820-GP Armada A38x board. The default boot device is still SPI NOR flash. To enable MMC booting on this board 2 things need to be changes: a) Change kwbimage.cfg BOOT_FROM sdio b) In the config header select #define CONFIG_SPL_BOOT_DEVICE SPL_BOOT_SDIO_MMC_CARD The generated image needs to be copied to the first bootable MMC partition: dd if=u-boot-spl.kwb of=/dev/sdX1 Signed-off-by: Stefan Roese <sr@denx.de> Cc: Luka Perkov <luka.perkov@sartura.hr> Cc: Dirk Eibach <eibach@gdsys.de>
2015-07-23arm: mvebu: db-88f6820: Add SPL support with DDR init codeStefan Roese
This patch adds SPL support for the Marvell DB-88F6820-GP board. With this change, the bin_hdr from the original Marvell U-boot is not needed any more on this board. The sources from bin_hdr (SERDES/PHY and DDR setup) are now integrated in mainline U-Boot. And this patch enables them for this board. Signed-off-by: Stefan Roese <sr@denx.de>
2015-07-10arm: mvebu: db-88f6820-gp: Add USB/EHCI supportStefan Roese
This patch enabled the USB/EHCI support for the Marvell DB-88F6820-GP eval board. Signed-off-by: Stefan Roese <sr@denx.de> Cc: Marek Vasut <marex@denx.de> Cc: Luka Perkov <luka.perkov@sartura.hr>
2015-07-10arm: mvebu: db-88f6820-gp.h: Add SATA/SCSI (AHCI) supportStefan Roese
Configure and enable the SATA/SCSI (AHCI) support for the Marvell DB-88F6820-GP eval board. Signed-off-by: Stefan Roese <sr@denx.de> Cc: Luka Perkov <luka.perkov@sartura.hr>
2015-07-10arm: mvebu: Add SATA/SCSI (AHCI) support for Armada A38xStefan Roese
This patch adds support for the common AHCI controller on the Marvell Armada 38x. Tested on the Marvell DB-88F6820-GP eval board. Signed-off-by: Stefan Roese <sr@denx.de> Cc: Luka Perkov <luka.perkov@sartura.hr>
2015-07-10arm: mvebu: db-88f6820-gp: Add MMC/SDIO supportStefan Roese
This patch adds MMC/SDIO support to the Marvell DB-88F6820-GP board configuration. Including support for the common partitions and filesystems. Signed-off-by: Stefan Roese <sr@denx.de> Cc: Pantelis Antoniou <panto@antoniou-consulting.com> Cc: Luka Perkov <luka.perkov@sartura.hr>
2015-06-28db-88f6820-gp.h: Load data blobs into lower memoryKevin Smith
By default on this platform, u-boot loads data into high memory in the range of 0x7Fxxxxxx, which generates a data abort when the kernel tries to read it. Config the u-boot environment to load the device tree and initrd image into lower memory to make them accessible to the kernel. Signed-off-by: Kevin Smith <kevin.smith@elecsyscorp.com> Acked-by: Stefan Roese <sr@denx.de>
2015-06-25Move defaults from config_cmd_default.h to KconfigJoe Hershberger
This sets the default commands Kconfig to match include/config_cmd_default.h commands in the common/Kconfig and removes them from include/configs. Signed-off-by: Joe Hershberger <joe.hershberger@ni.com> [trini: rastaban, am43xx_evm_usbhost_boot, am43xx_evm_ethboot updates] Signed-off-by: Tom Rini <trini@konsulko.com>
2015-05-05arm: mvebu: Add Armada A38x DB-88F6820-GP board supportStefan Roese
This patch adds support for the Marvell DB-88F6820-GP Armada A38x evaluation board. Supported peripherals are: - UART - Ethernet (mvneta) - I2C - SPI (including SPI NOR flash) Please note that this board support right now only supports the main U-Boot. Without the bin_hdr integration (DDR training etc). This will be added in a few days / weeks to complete this board port. But till then this U-Boot version can be run on the target via the original Marvell U-Boot via this command: tftpboot 4000000 db-88f6820-gp/u-boot.bin;go 4000000 Signed-off-by: Stefan Roese <sr@denx.de> Tested-by: Kevin Smith <kevin.smith@elecsyscorp.com> Tested-by: Dirk Eibach <dirk.eibach@gdsys.cc>
generated by cgit v1.2.3 (git 2.0.4) at 2024-05-10 04:42:27 +0000