/* SPDX-License-Identifier: GPL-2.0+ */
/*
 * Copyright (C) 2012 Freescale Semiconductor, Inc.
 * Copyright 2018 NXP
 *
 * Configuration settings for the Freescale i.MX6Q SabreSD board.
 */

#ifndef __MX6QSABRE_COMMON_CONFIG_H
#define __MX6QSABRE_COMMON_CONFIG_H

#include "mx6_common.h"
#include "imx_env.h"

#define CONFIG_IMX_THERMAL

/* Size of malloc() pool */
#define CONFIG_SYS_MALLOC_LEN		(16 * SZ_1M)

#define CONFIG_MXC_UART

/* MMC Configs */
#define CONFIG_SYS_FSL_ESDHC_ADDR      0

#define CONFIG_FEC_MXC
#define CONFIG_FEC_XCV_TYPE		RGMII
#define CONFIG_ETHPRIME			"eth0"

#define CONFIG_PHY_ATHEROS

#ifdef CONFIG_MX6S
#define SYS_NOSMP "nosmp"
#else
#define SYS_NOSMP
#endif

#ifdef CONFIG_NAND_BOOT
#define MFG_NAND_PARTITION "mtdparts=8000000.nor:1m(boot),-(rootfs)\\;gpmi-nand:64m(nandboot),16m(nandkernel),16m(nanddtb),16m(nandtee),-(nandrootfs)"
#else
#define MFG_NAND_PARTITION ""
#endif

#define CONFIG_CMD_READ
#define CONFIG_SERIAL_TAG
#define CONFIG_FASTBOOT_USB_DEV 0

#define CONFIG_MFG_ENV_SETTINGS \
	CONFIG_MFG_ENV_SETTINGS_DEFAULT \
	"initrd_addr=0x12C00000\0" \
	"initrd_high=0xffffffff\0" \
	"emmc_dev=3\0"\
	"sd_dev=2\0" \
	"weim_uboot=0x08001000\0"\
	"weim_base=0x08000000\0"\
	"spi_bus=0\0"\
	"spi_uboot=0x400\0" \
	"mtdparts=" MFG_NAND_PARTITION \
	"\0"\

#ifdef CONFIG_SUPPORT_EMMC_BOOT
#define EMMC_ENV \
	"emmcdev=2\0" \
	"update_emmc_firmware=" \
		"if test ${ip_dyn} = yes; then " \
			"setenv get_cmd dhcp; " \
		"else " \
			"setenv get_cmd tftp; " \
		"fi; " \
		"if ${get_cmd} ${update_sd_firmware_filename}; then " \
			"if mmc dev ${emmcdev} 1; then "	\
				"setexpr fw_sz ${filesize} / 0x200; " \
				"setexpr fw_sz ${fw_sz} + 1; "	\
				"mmc write ${loadaddr} 0x2 ${fw_sz}; " \
			"fi; "	\
		"fi\0"
#else
#define EMMC_ENV ""
#endif

#define CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG

#if defined(CONFIG_NAND_BOOT)
	/*
	 * The dts also enables the WEIN NOR which is mtd0.
	 * So the partions' layout for NAND is:
	 *     mtd1: 16M      (uboot)
	 *     mtd2: 16M      (kernel)
	 *     mtd3: 16M      (dtb)
	 *     mtd4: left     (rootfs)
	 */
#define CONFIG_EXTRA_ENV_SETTINGS \
	CONFIG_MFG_ENV_SETTINGS \
	TEE_ENV \
	"fdt_addr=0x18000000\0" \
	"tee_addr=0x20000000\0" \
	"fdt_high=0xffffffff\0"	  \
	"splashimage=0x28000000\0" \
	"console=" CONSOLE_DEV "\0" \
	"bootargs=console=" CONSOLE_DEV ",115200 ubi.mtd=nandrootfs "  \
		"root=ubi0:nandrootfs rootfstype=ubifs "		     \
		MFG_NAND_PARTITION \
		"\0" \
	"bootcmd=nand read ${loadaddr} 0x4000000 0xc00000;"\
		"nand read ${fdt_addr} 0x5000000 0x100000;"\
		"if test ${tee} = yes; then " \
			"nand read ${tee_addr} 0x4000000 0x400000;"\
			"bootm ${tee_addr} - ${fdt_addr};" \
		"else " \
			"bootz ${loadaddr} - ${fdt_addr};" \
		"fi\0"

#elif defined(CONFIG_SATA_BOOT)

#define CONFIG_EXTRA_ENV_SETTINGS \
		CONFIG_MFG_ENV_SETTINGS \
		TEE_ENV \
		"image=zImage\0" \
		"fdt_file=undefined\0" \
		"fdt_addr=0x18000000\0" \
		"fdt_high=0xffffffff\0"   \
		"splashimage=0x28000000\0" \
		"tee_addr=0x20000000\0" \
		"tee_file=undefined\0" \
		"findfdt="\
			"if test $fdt_file = undefined; then " \
				"if test $board_name = SABREAUTO && test $board_rev = MX6QP; then " \
					"setenv fdt_file imx6qp-sabreauto.dtb; fi; " \
				"if test $board_name = SABREAUTO && test $board_rev = MX6Q; then " \
					"setenv fdt_file imx6q-sabreauto.dtb; fi; " \
				"if test $board_name = SABREAUTO && test $board_rev = MX6DL; then " \
					"setenv fdt_file imx6dl-sabreauto.dtb; fi; " \
				"if test $board_name = SABRESD && test $board_rev = MX6QP; then " \
					"setenv fdt_file imx6qp-sabresd.dtb; fi; " \
				"if test $board_name = SABRESD && test $board_rev = MX6Q; then " \
					"setenv fdt_file imx6q-sabresd.dtb; fi; " \
				"if test $board_name = SABRESD && test $board_rev = MX6DL; then " \
					"setenv fdt_file imx6dl-sabresd.dtb; fi; " \
				"if test $fdt_file = undefined; then " \
					"echo WARNING: Could not determine dtb to use; " \
				"fi; " \
			"fi;\0" \
		"findtee="\
			"if test $tee_file = undefined; then " \
				"if test $board_name = SABREAUTO && test $board_rev = MX6QP; then " \
					"setenv tee_file uTee-6qpauto; fi; " \
				"if test $board_name = SABREAUTO && test $board_rev = MX6Q; then " \
					"setenv tee_file uTee-6qauto; fi; " \
				"if test $board_name = SABREAUTO && test $board_rev = MX6DL; then " \
					"setenv tee_file uTee-6dlauto; fi; " \
				"if test $board_name = SABRESD && test $board_rev = MX6QP; then " \
					"setenv tee_file uTee-6qpsdb; fi; " \
				"if test $board_name = SABRESD && test $board_rev = MX6Q; then " \
					"setenv tee_file uTee-6qsdb; fi; " \
				"if test $board_name = SABRESD && test $board_rev = MX6DL; then " \
					"setenv tee_file uTee-6dlsdb; fi; " \
				"if test $tee_file = undefined; then " \
					"echo WARNING: Could not determine tee to use; fi; " \
			"fi;\0" \
		"bootargs=console=" CONSOLE_DEV ",115200 \0"\
		"bootargs_sata=setenv bootargs ${bootargs} " \
			"root=/dev/sda2 rootwait rw \0" \
		"bootcmd_sata=run bootargs_sata; scsi scan; " \
			"run findfdt; run findtee;" \
			"fatload scsi 0:1 ${loadaddr} ${image}; " \
			"fatload scsi 0:1 ${fdt_addr} ${fdt_file}; " \
			"if test ${tee} = yes; then " \
				"fatload scsi 0:1 ${tee_addr} ${tee_file}; " \
				"bootm ${tee_addr} - ${fdt_addr}; " \
			"else " \
				"bootz ${loadaddr} - ${fdt_addr}; " \
			"fi \0"\
		"bootcmd=run bootcmd_sata \0"

#else

#define CONFIG_EXTRA_ENV_SETTINGS \
	CONFIG_MFG_ENV_SETTINGS \
	TEE_ENV \
	"epdc_waveform=epdc_splash.bin\0" \
	"script=boot.scr\0" \
	"image=zImage\0" \
	"fdt_file=undefined\0" \
	"fdt_addr=0x18000000\0" \
	"tee_addr=0x20000000\0" \
	"tee_file=undefined\0" \
	"boot_fdt=try\0" \
	"ip_dyn=yes\0" \
	"console=" CONSOLE_DEV "\0" \
	"dfuspi=dfu 0 sf 0:0:10000000:0\0" \
	"dfu_alt_info_spl=spl raw 0x400\0" \
	"dfu_alt_info_img=u-boot raw 0x10000\0" \
	"dfu_alt_info=spl raw 0x400\0" \
	"fdt_high=0xffffffff\0"	  \
	"initrd_high=0xffffffff\0" \
	"splashimage=0x28000000\0" \
	"mmcdev=" __stringify(CONFIG_SYS_MMC_ENV_DEV) "\0" \
	"mmcpart=1\0" \
	"finduuid=part uuid mmc ${mmcdev}:2 uuid\0" \
	"mmcroot=" CONFIG_MMCROOT " rootwait rw\0" \
	"mmcautodetect=yes\0" \
	"update_sd_firmware=" \
		"if test ${ip_dyn} = yes; then " \
			"setenv get_cmd dhcp; " \
		"else " \
			"setenv get_cmd tftp; " \
		"fi; " \
		"if mmc dev ${mmcdev}; then "	\
			"if ${get_cmd} ${update_sd_firmware_filename}; then " \
				"setexpr fw_sz ${filesize} / 0x200; " \
				"setexpr fw_sz ${fw_sz} + 1; "	\
				"mmc write ${loadaddr} 0x2 ${fw_sz}; " \
			"fi; "	\
		"fi\0" \
	EMMC_ENV	  \
	"smp=" SYS_NOSMP "\0"\
	"mmcargs=setenv bootargs console=${console},${baudrate} ${smp} " \
		"root=${mmcroot}\0" \
	"loadbootscript=" \
		"fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${script};\0" \
	"bootscript=echo Running bootscript from mmc ...; " \
		"source\0" \
	"loadimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${image}\0" \
	"loadfdt=fatload mmc ${mmcdev}:${mmcpart} ${fdt_addr} ${fdt_file}\0" \
	"loadtee=fatload mmc ${mmcdev}:${mmcpart} ${tee_addr} ${tee_file}\0" \
	"mmcboot=echo Booting from mmc ...; " \
		"run mmcargs; " \
		"if test ${tee} = yes; then " \
			"run loadfdt; run loadtee; bootm ${tee_addr} - ${fdt_addr}; " \
		"else " \
			"if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
				"if run loadfdt; then " \
					"bootz ${loadaddr} - ${fdt_addr}; " \
				"else " \
					"if test ${boot_fdt} = try; then " \
						"bootz; " \
					"else " \
						"echo WARN: Cannot load the DT; " \
					"fi; " \
				"fi; " \
			"else " \
				"bootz; " \
			"fi;" \
		"fi;\0" \
	"netargs=setenv bootargs console=${console},${baudrate} ${smp} " \
		"root=/dev/nfs " \
		"ip=dhcp nfsroot=${serverip}:${nfsroot},v3,tcp\0" \
	"netboot=echo Booting from net ...; " \
		"run netargs; " \
		"if test ${ip_dyn} = yes; then " \
			"setenv get_cmd dhcp; " \
		"else " \
			"setenv get_cmd tftp; " \
		"fi; " \
		"${get_cmd} ${image}; " \
		"if test ${tee} = yes; then " \
			"${get_cmd} ${tee_addr} ${tee_file}; " \
			"${get_cmd} ${fdt_addr} ${fdt_file}; " \
			"bootm ${tee_addr} - ${fdt_addr}; " \
		"else " \
			"if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
				"if ${get_cmd} ${fdt_addr} ${fdt_file}; then " \
					"bootz ${loadaddr} - ${fdt_addr}; " \
				"else " \
					"if test ${boot_fdt} = try; then " \
						"bootz; " \
					"else " \
						"echo WARN: Cannot load the DT; " \
					"fi; " \
				"fi; " \
			"else " \
				"bootz; " \
			"fi; " \
		"fi;\0" \
		"findfdt="\
			"if test $fdt_file = undefined; then " \
				"if test $board_name = SABREAUTO && test $board_rev = MX6QP; then " \
					"setenv fdt_file imx6qp-sabreauto.dtb; fi; " \
				"if test $board_name = SABREAUTO && test $board_rev = MX6Q; then " \
					"setenv fdt_file imx6q-sabreauto.dtb; fi; " \
				"if test $board_name = SABREAUTO && test $board_rev = MX6DL; then " \
					"setenv fdt_file imx6dl-sabreauto.dtb; fi; " \
				"if test $board_name = SABRESD && test $board_rev = MX6QP; then " \
					"setenv fdt_file imx6qp-sabresd.dtb; fi; " \
				"if test $board_name = SABRESD && test $board_rev = MX6Q; then " \
					"setenv fdt_file imx6q-sabresd.dtb; fi; " \
				"if test $board_name = SABRESD && test $board_rev = MX6DL; then " \
					"setenv fdt_file imx6dl-sabresd.dtb; fi; " \
				"if test $fdt_file = undefined; then " \
					"echo WARNING: Could not determine dtb to use; fi; " \
			"fi;\0" \
		"findtee="\
			"if test $tee_file = undefined; then " \
				"if test $board_name = SABREAUTO && test $board_rev = MX6QP; then " \
					"setenv tee_file uTee-6qpauto; fi; " \
				"if test $board_name = SABREAUTO && test $board_rev = MX6Q; then " \
					"setenv tee_file uTee-6qauto; fi; " \
				"if test $board_name = SABREAUTO && test $board_rev = MX6DL; then " \
					"setenv tee_file uTee-6dlauto; fi; " \
				"if test $board_name = SABRESD && test $board_rev = MX6QP; then " \
					"setenv tee_file uTee-6qpsdb; fi; " \
				"if test $board_name = SABRESD && test $board_rev = MX6Q; then " \
					"setenv tee_file uTee-6qsdb; fi; " \
				"if test $board_name = SABRESD && test $board_rev = MX6DL; then " \
					"setenv tee_file uTee-6dlsdb; fi; " \
				"if test $tee_file = undefined; then " \
					"echo WARNING: Could not determine tee to use; fi; " \
			"fi;\0" \

#define CONFIG_BOOTCOMMAND \
	"run findfdt;" \
	"run findtee;" \
	"mmc dev ${mmcdev};" \
	"if mmc rescan; then " \
		"if run loadbootscript; then " \
		"run bootscript; " \
		"else " \
			"if run loadimage; then " \
				"run mmcboot; " \
			"else run netboot; " \
			"fi; " \
		"fi; " \
	"else run netboot; fi"
#endif

#define CONFIG_ARP_TIMEOUT     200UL

#define CONFIG_SYS_MEMTEST_START       0x10000000
#define CONFIG_SYS_MEMTEST_END         0x10010000
#define CONFIG_SYS_MEMTEST_SCRATCH     0x10800000

/* Physical Memory Map */
#define PHYS_SDRAM                     MMDC0_ARB_BASE_ADDR

#define CONFIG_SYS_SDRAM_BASE          PHYS_SDRAM
#define CONFIG_SYS_INIT_RAM_ADDR       IRAM_BASE_ADDR
#define CONFIG_SYS_INIT_RAM_SIZE       IRAM_SIZE

#define CONFIG_SYS_INIT_SP_OFFSET \
	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
#define CONFIG_SYS_INIT_SP_ADDR \
	(CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)

#ifdef CONFIG_MTD_NOR_FLASH
#define CONFIG_SYS_FLASH_BASE           WEIM_ARB_BASE_ADDR
#define CONFIG_SYS_FLASH_SECT_SIZE      (128 * 1024)
#define CONFIG_SYS_MAX_FLASH_BANKS 1    /* max number of memory banks */
#define CONFIG_SYS_MAX_FLASH_SECT 256   /* max number of sectors on one chip */
#define CONFIG_SYS_FLASH_CFI            /* Flash memory is CFI compliant */
#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE /* Use buffered writes*/
#define CONFIG_SYS_FLASH_EMPTY_INFO
#define CONFIG_SYS_FLASH_CFI_WIDTH	FLASH_CFI_16BIT
#endif

#ifdef CONFIG_NAND_MXS

#define CONFIG_SYS_MAX_NAND_DEVICE     1
#define CONFIG_SYS_NAND_BASE           0x40000000
#define CONFIG_SYS_NAND_5_ADDR_CYCLE
#define CONFIG_SYS_NAND_ONFI_DETECTION
#define CONFIG_SYS_NAND_USE_FLASH_BBT

/* DMA stuff, needed for GPMI/MXS NAND support */
#endif

#if defined(CONFIG_ENV_IS_IN_MMC)
#elif defined(CONFIG_ENV_IS_IN_SPI_FLASH)
#define CONFIG_ENV_SPI_BUS             CONFIG_SF_DEFAULT_BUS
#define CONFIG_ENV_SPI_CS              CONFIG_SF_DEFAULT_CS
#define CONFIG_ENV_SPI_MODE            CONFIG_SF_DEFAULT_MODE
#define CONFIG_ENV_SPI_MAX_HZ          CONFIG_SF_DEFAULT_SPEED
#elif defined(CONFIG_ENV_IS_IN_FLASH)
#elif defined(CONFIG_ENV_IS_IN_NAND)
#elif defined(CONFIG_ENV_IS_IN_SATA)
#define CONFIG_SYS_SATA_ENV_DEV		0
#endif

/* I2C Configs */
#ifndef CONFIG_DM_I2C
#define CONFIG_SYS_I2C
#endif
#ifdef CONFIG_CMD_I2C
#define CONFIG_SYS_I2C_MXC
#define CONFIG_SYS_I2C_MXC_I2C1		/* enable I2C bus 1 */
#define CONFIG_SYS_I2C_MXC_I2C2		/* enable I2C bus 2 */
#define CONFIG_SYS_I2C_MXC_I2C3		/* enable I2C bus 3 */
#define CONFIG_SYS_I2C_SPEED		  100000
#endif

/* PMIC */
#ifndef CONFIG_DM_PMIC
#define CONFIG_POWER
#define CONFIG_POWER_I2C
#define CONFIG_POWER_PFUZE100
#define CONFIG_POWER_PFUZE100_I2C_ADDR 0x08
#endif

/* Framebuffer */
#define CONFIG_VIDEO_BMP_RLE8
#define CONFIG_SPLASH_SCREEN
#define CONFIG_SPLASH_SCREEN_ALIGN
#define CONFIG_BMP_16BPP
#define CONFIG_CMD_BMP
#define CONFIG_VIDEO_LOGO
#define CONFIG_VIDEO_BMP_LOGO
#define CONFIG_IMX_HDMI
#define CONFIG_IMX_VIDEO_SKIP

#if defined(CONFIG_ANDROID_SUPPORT)
#include "mx6sabreandroid_common.h"
#else
#define CONFIG_USBD_HS

#endif /* CONFIG_ANDROID_SUPPORT */
#endif                         /* __MX6QSABRE_COMMON_CONFIG_H */