diff options
Diffstat (limited to 'drivers/mtd/nand/mxc_nd2.c')
| -rw-r--r-- | drivers/mtd/nand/mxc_nd2.c | 1756 |
1 files changed, 1756 insertions, 0 deletions
diff --git a/drivers/mtd/nand/mxc_nd2.c b/drivers/mtd/nand/mxc_nd2.c new file mode 100644 index 000000000000..6b362ce05bb3 --- /dev/null +++ b/drivers/mtd/nand/mxc_nd2.c @@ -0,0 +1,1756 @@ +/* + * Copyright 2004-2010 Freescale Semiconductor, Inc. All Rights Reserved. + */ + +/* + * The code contained herein is licensed under the GNU General Public + * License. You may obtain a copy of the GNU General Public License + * Version 2 or later at the following locations: + * + * http://www.opensource.org/licenses/gpl-license.html + * http://www.gnu.org/copyleft/gpl.html + */ + +#include <linux/delay.h> +#include <linux/slab.h> +#include <linux/init.h> +#include <linux/io.h> +#include <linux/module.h> +#include <linux/mtd/mtd.h> +#include <linux/mtd/nand.h> +#include <linux/interrupt.h> +#include <linux/device.h> +#include <linux/platform_device.h> +#include <linux/clk.h> +#include <linux/err.h> +#include <linux/mtd/partitions.h> +#include <asm/mach/flash.h> +#include "mxc_nd2.h" +#include "nand_device_info.h" + +#define DVR_VER "3.0" + +/* Global address Variables */ +static void __iomem *nfc_axi_base, *nfc_ip_base; +static int nfc_irq; + +struct mxc_mtd_s { + struct mtd_info mtd; + struct nand_chip nand; + struct mtd_partition *parts; + struct device *dev; + int disable_bi_swap; /* disable bi swap */ + int ignore_bad_block; /* ignore bad block marker */ + void *saved_bbt; + int (*saved_block_bad)(struct mtd_info *mtd, loff_t ofs, int getchip); + int clk_active; +}; + +static struct mxc_mtd_s *mxc_nand_data; + +/* + * Define delay timeout value + */ +#define TROP_US_DELAY (1000 * 1000) + +struct nand_info { + bool bStatusRequest; + u16 colAddr; +}; + +static struct nand_info g_nandfc_info; + +#ifdef CONFIG_MTD_NAND_MXC_SWECC +static int hardware_ecc; +#else +static int hardware_ecc = 1; +#endif + +static u8 num_of_interleave = 1; + +static u8 *data_buf; +static u8 *oob_buf; + +static int g_page_mask; + +static struct clk *nfc_clk; + +/* + * OOB placement block for use with hardware ecc generation + */ +static struct nand_ecclayout nand_hw_eccoob_512 = { + .eccbytes = 9, + .eccpos = {7, 8, 9, 10, 11, 12, 13, 14, 15}, + .oobavail = 4, + .oobfree = {{0, 4} } +}; + +static struct nand_ecclayout nand_hw_eccoob_2k = { + .eccbytes = 9, + .eccpos = {7, 8, 9, 10, 11, 12, 13, 14, 15}, + .oobavail = 4, + .oobfree = {{2, 4} } +}; + +static struct nand_ecclayout nand_hw_eccoob_4k = { + .eccbytes = 9, + .eccpos = {7, 8, 9, 10, 11, 12, 13, 14, 15}, + .oobavail = 4, + .oobfree = {{2, 4} } +}; + +/*! + * @defgroup NAND_MTD NAND Flash MTD Driver for MXC processors + */ + +/*! + * @file mxc_nd2.c + * + * @brief This file contains the hardware specific layer for NAND Flash on + * MXC processor + * + * @ingroup NAND_MTD + */ + +#ifdef CONFIG_MTD_PARTITIONS +static const char *part_probes[] = { "RedBoot", "cmdlinepart", NULL }; +#endif + +static wait_queue_head_t irq_waitq; + +static irqreturn_t mxc_nfc_irq(int irq, void *dev_id) +{ + /* Disable Interuupt */ + raw_write(raw_read(REG_NFC_INTRRUPT) | NFC_INT_MSK, REG_NFC_INTRRUPT); + wake_up(&irq_waitq); + + return IRQ_HANDLED; +} + +static void mxc_nand_bi_swap(struct mtd_info *mtd) +{ + u16 ma, sa, nma, nsa; + + if (!IS_LARGE_PAGE_NAND) + return; + + /* Disable bi swap if the user set disable_bi_swap at sys entry */ + if (mxc_nand_data->disable_bi_swap) + return; + + ma = __raw_readw(BAD_BLK_MARKER_MAIN); + sa = __raw_readw(BAD_BLK_MARKER_SP); + + nma = (ma & 0xFF00) | (sa >> 8); + nsa = (sa & 0x00FF) | (ma << 8); + + __raw_writew(nma, BAD_BLK_MARKER_MAIN); + __raw_writew(nsa, BAD_BLK_MARKER_SP); +} + +static void nfc_memcpy(void *dest, void *src, int len) +{ + u8 *d = dest; + u8 *s = src; + + while (len > 0) { + if (len >= 4) { + *(u32 *)d = *(u32 *)s; + d += 4; + s += 4; + len -= 4; + } else { + *(u16 *)d = *(u16 *)s; + len -= 2; + break; + } + } + + if (len) + BUG(); +} + +/* + * Functions to transfer data to/from spare erea. + */ +static void +copy_spare(struct mtd_info *mtd, void *pbuf, void *pspare, int len, bool bfrom) +{ + u16 i, j; + u16 m = mtd->oobsize; + u16 n = mtd->writesize >> 9; + u8 *d = (u8 *) pbuf; + u8 *s = (u8 *) pspare; + u16 t = SPARE_LEN; + + m /= num_of_interleave; + n /= num_of_interleave; + + j = (m / n >> 1) << 1; + + if (bfrom) { + for (i = 0; i < n - 1; i++) + nfc_memcpy(&d[i * j], &s[i * t], j); + + /* the last section */ + nfc_memcpy(&d[i * j], &s[i * t], len - i * j); + } else { + for (i = 0; i < n - 1; i++) + nfc_memcpy(&s[i * t], &d[i * j], j); + + /* the last section */ + nfc_memcpy(&s[i * t], &d[i * j], len - i * j); + } +} + +/*! + * This function polls the NFC to wait for the basic operation to complete by + * checking the INT bit of config2 register. + * + * @param maxRetries number of retry attempts (separated by 1 us) + * @param useirq True if IRQ should be used rather than polling + */ +static void wait_op_done(int maxRetries, bool useirq) +{ + if (useirq) { + if ((raw_read(REG_NFC_OPS_STAT) & NFC_OPS_STAT) == 0) { + /* enable interrupt */ + raw_write(raw_read(REG_NFC_INTRRUPT) & ~NFC_INT_MSK, + REG_NFC_INTRRUPT); + if (!wait_event_timeout(irq_waitq, + (raw_read(REG_NFC_OPS_STAT) & NFC_OPS_STAT), + msecs_to_jiffies(TROP_US_DELAY / 1000)) > 0) { + /* disable interrupt */ + raw_write(raw_read(REG_NFC_INTRRUPT) + | NFC_INT_MSK, REG_NFC_INTRRUPT); + + printk(KERN_WARNING "%s(%d): INT not set\n", + __func__, __LINE__); + return; + } + } + WRITE_NFC_IP_REG((raw_read(REG_NFC_OPS_STAT) & + ~NFC_OPS_STAT), REG_NFC_OPS_STAT); + } else { + while (1) { + maxRetries--; + if (raw_read(REG_NFC_OPS_STAT) & NFC_OPS_STAT) { + WRITE_NFC_IP_REG((raw_read(REG_NFC_OPS_STAT) & + ~NFC_OPS_STAT), + REG_NFC_OPS_STAT); + break; + } + udelay(1); + if (maxRetries <= 0) { + printk(KERN_WARNING "%s(%d): INT not set\n", + __func__, __LINE__); + break; + } + } + } +} + +static inline void send_atomic_cmd(u16 cmd, bool useirq) +{ + /* fill command */ + raw_write(cmd, REG_NFC_FLASH_CMD); + + /* send out command */ + raw_write(NFC_CMD, REG_NFC_OPS); + + /* Wait for operation to complete */ + wait_op_done(TROP_US_DELAY, useirq); +} + +static void mxc_do_addr_cycle(struct mtd_info *mtd, int column, int page_addr); +static int mxc_check_ecc_status(struct mtd_info *mtd); + +#ifdef NFC_AUTO_MODE_ENABLE +/*! + * This function handle the interleave related work + * @param mtd mtd info + * @param cmd command + */ +static void auto_cmd_interleave(struct mtd_info *mtd, u16 cmd) +{ + u32 i, page_addr, ncs; + u32 j = num_of_interleave; + struct nand_chip *this = mtd->priv; + u32 addr_low = raw_read(NFC_FLASH_ADDR0); + u32 addr_high = raw_read(NFC_FLASH_ADDR8); + u8 *dbuf = data_buf; + u8 *obuf = oob_buf; + u32 dlen = mtd->writesize / j; + u32 olen = mtd->oobsize / j; + + /* adjust the addr value + * since ADD_OP mode is 01 + */ + if (cmd == NAND_CMD_ERASE2) + page_addr = addr_low; + else + page_addr = addr_low >> 16 | addr_high << 16; + + ncs = NFC_GET_NFC_ACTIVE_CS(); + + if (j > 1) { + page_addr *= j; + } else { + page_addr *= this->numchips; + page_addr += ncs; + } + + switch (cmd) { + case NAND_CMD_PAGEPROG: + for (i = 0; i < j; i++) { + /* reset addr cycle */ + mxc_do_addr_cycle(mtd, 0, page_addr++); + + /* data transfer */ + memcpy(MAIN_AREA0, dbuf, dlen); + copy_spare(mtd, obuf, SPARE_AREA0, olen, false); + mxc_nand_bi_swap(mtd); + + /* update the value */ + dbuf += dlen; + obuf += olen; + + NFC_SET_RBA(0); + raw_write(NFC_AUTO_PROG, REG_NFC_OPS); + + /* wait auto_prog_done bit set */ + while (!(raw_read(REG_NFC_OPS_STAT) & NFC_OP_DONE)) + ; + } + + wait_op_done(TROP_US_DELAY, true); + while (!(raw_read(REG_NFC_OPS_STAT) & NFC_RB)); + + break; + case NAND_CMD_READSTART: + for (i = 0; i < j; i++) { + /* reset addr cycle */ + mxc_do_addr_cycle(mtd, 0, page_addr++); + + NFC_SET_RBA(0); + raw_write(NFC_AUTO_READ, REG_NFC_OPS); + wait_op_done(TROP_US_DELAY, true); + + /* check ecc error */ + mxc_check_ecc_status(mtd); + + /* data transfer */ + mxc_nand_bi_swap(mtd); + memcpy(dbuf, MAIN_AREA0, dlen); + copy_spare(mtd, obuf, SPARE_AREA0, olen, true); + + /* update the value */ + dbuf += dlen; + obuf += olen; + } + break; + case NAND_CMD_ERASE2: + for (i = 0; i < j; i++) { + mxc_do_addr_cycle(mtd, -1, page_addr++); + raw_write(NFC_AUTO_ERASE, REG_NFC_OPS); + wait_op_done(TROP_US_DELAY, true); + } + break; + case NAND_CMD_RESET: + for (i = 0; i < j; i++) { + if (j > 1) + NFC_SET_NFC_ACTIVE_CS(i); + send_atomic_cmd(cmd, false); + } + break; + default: + break; + } +} +#endif + +static void send_addr(u16 addr, bool useirq); + +/*! + * This function issues the specified command to the NAND device and + * waits for completion. + * + * @param cmd command for NAND Flash + * @param useirq True if IRQ should be used rather than polling + */ +static void send_cmd(struct mtd_info *mtd, u16 cmd, bool useirq) +{ + DEBUG(MTD_DEBUG_LEVEL3, "send_cmd(0x%x, %d)\n", cmd, useirq); + +#ifdef NFC_AUTO_MODE_ENABLE + switch (cmd) { + case NAND_CMD_READ0: + case NAND_CMD_READOOB: + raw_write(NAND_CMD_READ0, REG_NFC_FLASH_CMD); + break; + case NAND_CMD_SEQIN: + case NAND_CMD_ERASE1: + raw_write(cmd, REG_NFC_FLASH_CMD); + break; + case NAND_CMD_PAGEPROG: + case NAND_CMD_ERASE2: + case NAND_CMD_READSTART: + raw_write(raw_read(REG_NFC_FLASH_CMD) | cmd << NFC_CMD_1_SHIFT, + REG_NFC_FLASH_CMD); + auto_cmd_interleave(mtd, cmd); + break; + case NAND_CMD_READID: + send_atomic_cmd(cmd, useirq); + send_addr(0, false); + break; + case NAND_CMD_RESET: + auto_cmd_interleave(mtd, cmd); + break; + case NAND_CMD_STATUS: + send_atomic_cmd(cmd, useirq); + break; + default: + break; + } +#else + send_atomic_cmd(cmd, useirq); +#endif +} + +/*! + * This function sends an address (or partial address) to the + * NAND device. The address is used to select the source/destination for + * a NAND command. + * + * @param addr address to be written to NFC. + * @param useirq True if IRQ should be used rather than polling + */ +static void send_addr(u16 addr, bool useirq) +{ + DEBUG(MTD_DEBUG_LEVEL3, "send_addr(0x%x %d)\n", addr, useirq); + + /* fill address */ + raw_write((addr << NFC_FLASH_ADDR_SHIFT), REG_NFC_FLASH_ADDR); + + /* send out address */ + raw_write(NFC_ADDR, REG_NFC_OPS); + + /* Wait for operation to complete */ + wait_op_done(TROP_US_DELAY, useirq); +} + +/*! + * This function requests the NFC to initate the transfer + * of data currently in the NFC RAM buffer to the NAND device. + * + * @param buf_id Specify Internal RAM Buffer number + */ +static void send_prog_page(u8 buf_id) +{ +#ifndef NFC_AUTO_MODE_ENABLE + DEBUG(MTD_DEBUG_LEVEL3, "%s\n", __FUNCTION__); + + /* set ram buffer id */ + NFC_SET_RBA(buf_id); + + /* transfer data from NFC ram to nand */ + raw_write(NFC_INPUT, REG_NFC_OPS); + + /* Wait for operation to complete */ + wait_op_done(TROP_US_DELAY, true); +#endif +} + +/*! + * This function requests the NFC to initated the transfer + * of data from the NAND device into in the NFC ram buffer. + * + * @param buf_id Specify Internal RAM Buffer number + */ +static void send_read_page(u8 buf_id) +{ +#ifndef NFC_AUTO_MODE_ENABLE + DEBUG(MTD_DEBUG_LEVEL3, "%s(%d)\n", __FUNCTION__, buf_id); + + /* set ram buffer id */ + NFC_SET_RBA(buf_id); + + /* transfer data from nand to NFC ram */ + raw_write(NFC_OUTPUT, REG_NFC_OPS); + + /* Wait for operation to complete */ + wait_op_done(TROP_US_DELAY, true); +#endif +} + +/*! + * This function requests the NFC to perform a read of the + * NAND device ID. + */ +static void send_read_id(void) +{ + /* Set RBA bits for BUFFER0 */ + NFC_SET_RBA(0); + + /* Read ID into main buffer */ + raw_write(NFC_ID, REG_NFC_OPS); + + /* Wait for operation to complete */ + wait_op_done(TROP_US_DELAY, false); + +} + +#ifdef NFC_AUTO_MODE_ENABLE +static inline void read_dev_status(u16 *status) +{ + u32 mask = 0xFF << 16; + + /* use atomic mode to read status instead + of using auto mode,auto-mode has issues + and the status is not correct. + */ + raw_write(NFC_STATUS, REG_NFC_OPS); + + wait_op_done(TROP_US_DELAY, true); + + *status = (raw_read(NFC_CONFIG1) & mask) >> 16; + +} +#endif + +/*! + * This function requests the NFC to perform a read of the + * NAND device status and returns the current status. + * + * @return device status + */ +static u16 get_dev_status(void) +{ +#ifdef NFC_AUTO_MODE_ENABLE + int i; + u16 status = 0; + int cs = NFC_GET_NFC_ACTIVE_CS(); + + for (i = 0; i < num_of_interleave; i++) { + + /* set ative cs */ + NFC_SET_NFC_ACTIVE_CS(i); + + /* FIXME, NFC Auto erase may have + * problem, have to pollingit until + * the nand get idle, otherwise + * it may get error + */ + read_dev_status(&status); + if (status & NAND_STATUS_FAIL) + break; + } + + /* Restore active CS */ + NFC_SET_NFC_ACTIVE_CS(cs); + + return status; +#else + volatile u16 *mainBuf = MAIN_AREA1; + u8 val = 1; + u16 ret; + + /* Set ram buffer id */ + NFC_SET_RBA(val); + + /* Read status into main buffer */ + raw_write(NFC_STATUS, REG_NFC_OPS); + + /* Wait for operation to complete */ + wait_op_done(TROP_US_DELAY, true); + + /* Status is placed in first word of main buffer */ + /* get status, then recovery area 1 data */ + ret = *mainBuf; + + return ret; +#endif +} + +static void mxc_nand_enable_hwecc(struct mtd_info *mtd, int mode) +{ + raw_write((raw_read(REG_NFC_ECC_EN) | NFC_ECC_EN), REG_NFC_ECC_EN); + return; +} + +/* + * Function to record the ECC corrected/uncorrected errors resulted + * after a page read. This NFC detects and corrects upto to 4 symbols + * of 9-bits each. + */ +static int mxc_check_ecc_status(struct mtd_info *mtd) +{ + u32 ecc_stat, err; + int no_subpages = 1; + int ret = 0; + u8 ecc_bit_mask = 0xf; + + no_subpages = mtd->writesize >> 9; + + no_subpages /= num_of_interleave; + + ecc_stat = GET_NFC_ECC_STATUS(); + do { + err = ecc_stat & ecc_bit_mask; + if (err == ecc_bit_mask) { + mtd->ecc_stats.failed++; + printk(KERN_WARNING "UnCorrectable RS-ECC Error\n"); + return -1; + } else { + ret += err; + } + ecc_stat >>= 4; + } while (--no_subpages); + + pr_debug("Correctable ECC Error(%d)\n", ret); + + return ret; +} + +/* + * Function to correct the detected errors. This NFC corrects all the errors + * detected. So this function just return 0. + */ +static int mxc_nand_correct_data(struct mtd_info *mtd, u_char *dat, + u_char *read_ecc, u_char *calc_ecc) +{ + return 0; +} + +/* + * Function to calculate the ECC for the data to be stored in the Nand device. + * This NFC has a hardware RS(511,503) ECC engine together with the RS ECC + * CONTROL blocks are responsible for detection and correction of up to + * 8 symbols of 9 bits each in 528 byte page. + * So this function is just return 0. + */ + +static int mxc_nand_calculate_ecc(struct mtd_info *mtd, const u_char *dat, + u_char *ecc_code) +{ + return 0; +} + +/*! + * This function id is used to read the data buffer from the NAND Flash. To + * read the data from NAND Flash first the data output cycle is initiated by + * the NFC, which copies the data to RAMbuffer. This data of length \b len is + * then copied to buffer \b buf. + * + * @param mtd MTD structure for the NAND Flash + * @param buf data to be read from NAND Flash + * @param len number of bytes to be read + */ +static void mxc_nand_read_buf(struct mtd_info *mtd, u_char * buf, int len) +{ + u16 col = g_nandfc_info.colAddr; + + if (mtd->writesize) { + + int j = mtd->writesize - col; + int n = mtd->oobsize + j; + + n = min(n, len); + + if (j > 0) { + if (n > j) { + memcpy(buf, &data_buf[col], j); + memcpy(buf + j, &oob_buf[0], n - j); + } else { + memcpy(buf, &data_buf[col], n); + } + } else { + col -= mtd->writesize; + memcpy(buf, &oob_buf[col], len); + } + + /* update */ + g_nandfc_info.colAddr += n; + + } else { + /* At flash identify phase, + * mtd->writesize has not been + * set correctly, it should + * be zero.And len will less 2 + */ + memcpy(buf, &data_buf[col], len); + + /* update */ + g_nandfc_info.colAddr += len; + } + +} + +/*! + * This function reads byte from the NAND Flash + * + * @param mtd MTD structure for the NAND Flash + * + * @return data read from the NAND Flash + */ +static uint8_t mxc_nand_read_byte(struct mtd_info *mtd) +{ + uint8_t ret; + + /* Check for status request */ + if (g_nandfc_info.bStatusRequest) { + return get_dev_status() & 0xFF; + } + + mxc_nand_read_buf(mtd, &ret, 1); + + return ret; +} + +/*! + * This function reads word from the NAND Flash + * + * @param mtd MTD structure for the NAND Flash + * + * @return data read from the NAND Flash + */ +static u16 mxc_nand_read_word(struct mtd_info *mtd) +{ + u16 ret; + + mxc_nand_read_buf(mtd, (uint8_t *) &ret, sizeof(u16)); + + return ret; +} + +/*! + * This function reads byte from the NAND Flash + * + * @param mtd MTD structure for the NAND Flash + * + * @return data read from the NAND Flash + */ +static u_char mxc_nand_read_byte16(struct mtd_info *mtd) +{ + /* Check for status request */ + if (g_nandfc_info.bStatusRequest) { + return get_dev_status() & 0xFF; + } + + return mxc_nand_read_word(mtd) & 0xFF; +} + +/*! + * This function writes data of length \b len from buffer \b buf to the NAND + * internal RAM buffer's MAIN area 0. + * + * @param mtd MTD structure for the NAND Flash + * @param buf data to be written to NAND Flash + * @param len number of bytes to be written + */ +static void mxc_nand_write_buf(struct mtd_info *mtd, + const u_char *buf, int len) +{ + u16 col = g_nandfc_info.colAddr; + int j = mtd->writesize - col; + int n = mtd->oobsize + j; + + n = min(n, len); + + if (j > 0) { + if (n > j) { + memcpy(&data_buf[col], buf, j); + memcpy(&oob_buf[0], buf + j, n - j); + } else { + memcpy(&data_buf[col], buf, n); + } + } else { + col -= mtd->writesize; + memcpy(&oob_buf[col], buf, len); + } + + /* update */ + g_nandfc_info.colAddr += n; +} + +/*! + * This function is used by the upper layer to verify the data in NAND Flash + * with the data in the \b buf. + * + * @param mtd MTD structure for the NAND Flash + * @param buf data to be verified + * @param len length of the data to be verified + * + * @return -EFAULT if error else 0 + * + */ +static int mxc_nand_verify_buf(struct mtd_info *mtd, const u_char * buf, + int len) +{ + u_char *s = data_buf; + + const u_char *p = buf; + + for (; len > 0; len--) { + if (*p++ != *s++) + return -EFAULT; + } + + return 0; +} + +/*! + * This function will enable NFC clock + * + */ +static inline void mxc_nand_clk_enable(void) +{ + if (!mxc_nand_data->clk_active) { + clk_enable(nfc_clk); + mxc_nand_data->clk_active = 1; + } +} + +/*! + * This function will disable NFC clock + * + */ +static inline void mxc_nand_clk_disable(void) +{ + if (mxc_nand_data->clk_active) { + clk_disable(nfc_clk); + mxc_nand_data->clk_active = 0; + } +} + +/*! + * This function is used by upper layer for select and deselect of the NAND + * chip + * + * @param mtd MTD structure for the NAND Flash + * @param chip val indicating select or deselect + */ +static void mxc_nand_select_chip(struct mtd_info *mtd, int chip) +{ + + switch (chip) { + case -1: + /* Disable the NFC clock */ + mxc_nand_clk_disable(); + + break; + case 0 ... NFC_GET_MAXCHIP_SP(): + /* Enable the NFC clock */ + mxc_nand_clk_enable(); + NFC_SET_NFC_ACTIVE_CS(chip); + + break; + + default: + break; + } +} + +/* + * Function to perform the address cycles. + */ +static void mxc_do_addr_cycle(struct mtd_info *mtd, int column, int page_addr) +{ +#ifdef NFC_AUTO_MODE_ENABLE + + if (page_addr != -1 && column != -1) { + u32 mask = 0xFFFF; + /* the column address */ + raw_write(column & mask, NFC_FLASH_ADDR0); + raw_write((raw_read(NFC_FLASH_ADDR0) | + ((page_addr & mask) << 16)), NFC_FLASH_ADDR0); + /* the row address */ + raw_write(((raw_read(NFC_FLASH_ADDR8) & (mask << 16)) | + ((page_addr & (mask << 16)) >> 16)), + NFC_FLASH_ADDR8); + } else if (page_addr != -1) { + raw_write(page_addr, NFC_FLASH_ADDR0); + raw_write(0, NFC_FLASH_ADDR8); + } + + DEBUG(MTD_DEBUG_LEVEL3, + "AutoMode:the ADDR REGS value is (0x%x, 0x%x)\n", + raw_read(NFC_FLASH_ADDR0), raw_read(NFC_FLASH_ADDR8)); +#else + + u32 page_mask = g_page_mask; + + if (column != -1) { + send_addr(column & 0xFF, true); + if (IS_2K_PAGE_NAND) { + /* another col addr cycle for 2k page */ + send_addr((column >> 8) & 0xF, true); + } else if (IS_4K_PAGE_NAND) { + /* another col addr cycle for 4k page */ + send_addr((column >> 8) & 0x1F, true); + } + } + if (page_addr != -1) { + do { + send_addr((page_addr & 0xff), true); + page_mask >>= 8; + page_addr >>= 8; + } while (page_mask != 0); + } +#endif +} + +/*! + * This function is used by the upper layer to write command to NAND Flash for + * different operations to be carried out on NAND Flash + * + * @param mtd MTD structure for the NAND Flash + * @param command command for NAND Flash + * @param column column offset for the page read + * @param page_addr page to be read from NAND Flash + */ +static void mxc_nand_command(struct mtd_info *mtd, unsigned command, + int column, int page_addr) +{ + bool useirq = true; + + DEBUG(MTD_DEBUG_LEVEL3, + "mxc_nand_command (cmd = 0x%x, col = 0x%x, page = 0x%x)\n", + command, column, page_addr); + /* + * Reset command state information + */ + g_nandfc_info.bStatusRequest = false; + + /* + * Command pre-processing step + */ + switch (command) { + case NAND_CMD_STATUS: + g_nandfc_info.colAddr = 0; + g_nandfc_info.bStatusRequest = true; + break; + + case NAND_CMD_READ0: + g_nandfc_info.colAddr = column; + break; + + case NAND_CMD_READOOB: + g_nandfc_info.colAddr = column; + command = NAND_CMD_READ0; + break; + + case NAND_CMD_SEQIN: + if (column != 0) { + + /* FIXME: before send SEQIN command for + * partial write,We need read one page out. + * FSL NFC does not support partial write + * It alway send out 512+ecc+512+ecc ... + * for large page nand flash. But for small + * page nand flash, it did support SPARE + * ONLY operation. But to make driver + * simple. We take the same as large page,read + * whole page out and update. As for MLC nand + * NOP(num of operation) = 1. Partial written + * on one programed page is not allowed! We + * can't limit it on the driver, it need the + * upper layer applicaiton take care it + */ + + mxc_nand_command(mtd, NAND_CMD_READ0, 0, page_addr); + } + + g_nandfc_info.colAddr = column; + column = 0; + + break; + + case NAND_CMD_PAGEPROG: +#ifndef NFC_AUTO_MODE_ENABLE + /* FIXME:the NFC interal buffer + * access has some limitation, it + * does not allow byte access. To + * make the code simple and ease use + * not every time check the address + * alignment.Use the temp buffer + * to accomadate the data.since We + * know data_buf will be at leat 4 + * byte alignment, so we can use + * memcpy safely + */ + nfc_memcpy(MAIN_AREA0, data_buf, mtd->writesize); + copy_spare(mtd, oob_buf, SPARE_AREA0, mtd->oobsize, false); + mxc_nand_bi_swap(mtd); +#endif + + if (IS_LARGE_PAGE_NAND) + PROG_PAGE(); + else + send_prog_page(0); + + break; + + case NAND_CMD_ERASE1: + break; + case NAND_CMD_ERASE2: + break; + } + + /* + * Write out the command to the device. + */ + send_cmd(mtd, command, useirq); + + mxc_do_addr_cycle(mtd, column, page_addr); + + /* + * Command post-processing step + */ + switch (command) { + + case NAND_CMD_READOOB: + case NAND_CMD_READ0: + if (IS_LARGE_PAGE_NAND) { + /* send read confirm command */ + send_cmd(mtd, NAND_CMD_READSTART, true); + /* read for each AREA */ + READ_PAGE(); + } else { + send_read_page(0); + } + +#ifndef NFC_AUTO_MODE_ENABLE + /* FIXME, the NFC interal buffer + * access has some limitation, it + * does not allow byte access. To + * make the code simple and ease use + * not every time check the address + * alignment.Use the temp buffer + * to accomadate the data.since We + * know data_buf will be at leat 4 + * byte alignment, so we can use + * memcpy safely + */ + mxc_nand_bi_swap(mtd); + nfc_memcpy(data_buf, MAIN_AREA0, mtd->writesize); + copy_spare(mtd, oob_buf, SPARE_AREA0, mtd->oobsize, true); +#endif + + break; + + case NAND_CMD_READID: + send_read_id(); + g_nandfc_info.colAddr = column; + nfc_memcpy(data_buf, MAIN_AREA0, 2048); + + break; + } +} + +static int mxc_nand_read_oob(struct mtd_info *mtd, + struct nand_chip *chip, int page, int sndcmd) +{ + if (sndcmd) { + + chip->cmdfunc(mtd, NAND_CMD_READ0, 0x00, page); + sndcmd = 0; + } + + memcpy(chip->oob_poi, oob_buf, mtd->oobsize); + + return sndcmd; +} + +static int mxc_nand_read_page(struct mtd_info *mtd, struct nand_chip *chip, + uint8_t *buf, int page) +{ + +#ifndef NFC_AUTO_MODE_ENABLE + mxc_check_ecc_status(mtd); +#endif + + memcpy(buf, data_buf, mtd->writesize); + memcpy(chip->oob_poi, oob_buf, mtd->oobsize); + + return 0; +} + +static void mxc_nand_write_page(struct mtd_info *mtd, struct nand_chip *chip, + const uint8_t *buf) +{ + memcpy(data_buf, buf, mtd->writesize); + memcpy(oob_buf, chip->oob_poi, mtd->oobsize); + +} + +/*! + * mxc_nand_block_bad - Claims all blocks are good + * In principle, this function is *only* called when the NAND Flash MTD system + * isn't allowed to keep an in-memory bad block table, so it is forced to ask + * the driver for bad block information. + * + * In fact, we permit the NAND Flash MTD system to have an in-memory BBT, so + * this function is *only* called when we take it away. + * + * We take away the in-memory BBT when the user sets the "ignorebad" parameter, + * which indicates that all blocks should be reported good. + * + * Thus, this function is only called when we want *all* blocks to look good, + * so it *always* return success. + * + * @mtd: Ignored. + * @ofs: Ignored. + * @getchip: Ignored. + */ +static int mxc_nand_block_bad(struct mtd_info *mtd, loff_t ofs, int getchip) +{ + return 0; +} + +/* Define some generic bad / good block scan pattern which are used + * while scanning a device for factory marked good / bad blocks. */ +static uint8_t scan_ff_pattern[] = { 0xff, 0xff }; + +static struct nand_bbt_descr smallpage_memorybased = { + .options = NAND_BBT_SCAN2NDPAGE, + .offs = 5, + .len = 1, + .pattern = scan_ff_pattern +}; + +static struct nand_bbt_descr largepage_memorybased = { + .options = 0, + .offs = 0, + .len = 2, + .pattern = scan_ff_pattern +}; + +/* Generic flash bbt decriptors +*/ +static uint8_t bbt_pattern[] = { 'B', 'b', 't', '0' }; +static uint8_t mirror_pattern[] = { '1', 't', 'b', 'B' }; + +static struct nand_bbt_descr bbt_main_descr = { + .options = NAND_BBT_LASTBLOCK | NAND_BBT_CREATE | NAND_BBT_WRITE + | NAND_BBT_2BIT | NAND_BBT_VERSION, + .offs = 0, + .len = 4, + .veroffs = 4, + .maxblocks = 4, + .pattern = bbt_pattern +}; + +static struct nand_bbt_descr bbt_mirror_descr = { + .options = NAND_BBT_LASTBLOCK | NAND_BBT_CREATE | NAND_BBT_WRITE + | NAND_BBT_2BIT | NAND_BBT_VERSION, + .offs = 0, + .len = 4, + .veroffs = 4, + .maxblocks = 4, + .pattern = mirror_pattern +}; + +static int mxc_nand_scan_bbt(struct mtd_info *mtd) +{ + struct nand_chip *this = mtd->priv; + + g_page_mask = this->pagemask; + + if (IS_2K_PAGE_NAND) { + NFC_SET_NFMS(1 << NFMS_NF_PG_SZ); + this->ecc.layout = &nand_hw_eccoob_2k; + } else if (IS_4K_PAGE_NAND) { + NFC_SET_NFMS(1 << NFMS_NF_PG_SZ); + this->ecc.layout = &nand_hw_eccoob_4k; + } else { + this->ecc.layout = &nand_hw_eccoob_512; + } + + /* propagate ecc.layout to mtd_info */ + mtd->ecclayout = this->ecc.layout; + + /* jffs2 not write oob */ + mtd->flags &= ~MTD_OOB_WRITEABLE; + + /* fix up the offset */ + largepage_memorybased.offs = BAD_BLK_MARKER_OOB_OFFS; + + /* keep compatible for bbt table with old soc */ + if (cpu_is_mx53()) { + bbt_mirror_descr.offs = BAD_BLK_MARKER_OOB_OFFS + 2; + bbt_main_descr.offs = BAD_BLK_MARKER_OOB_OFFS + 2; + bbt_mirror_descr.veroffs = bbt_mirror_descr.offs + 4; + bbt_main_descr.veroffs = bbt_main_descr.offs + 4; + } + + /* use flash based bbt */ + this->bbt_td = &bbt_main_descr; + this->bbt_md = &bbt_mirror_descr; + + /* update flash based bbt */ + this->options |= NAND_USE_FLASH_BBT; + + if (!this->badblock_pattern) { + this->badblock_pattern = (mtd->writesize > 512) ? + &largepage_memorybased : &smallpage_memorybased; + } + + /* Build bad block table */ + return nand_scan_bbt(mtd, this->badblock_pattern); +} + +static int mxc_get_resources(struct platform_device *pdev) +{ + struct resource *r; + int error = 0; + +#define MXC_NFC_NO_IP_REG \ + (cpu_is_mx25() || cpu_is_mx31() || cpu_is_mx32() || cpu_is_mx35()) + + r = platform_get_resource(pdev, IORESOURCE_MEM, 0); + if (!r) { + error = -ENXIO; + goto out_0; + } + nfc_axi_base = ioremap(r->start, resource_size(r)); + + if (!MXC_NFC_NO_IP_REG) { + r = platform_get_resource(pdev, IORESOURCE_MEM, 1); + if (!r) { + error = -ENXIO; + goto out_1; + } + } + nfc_ip_base = ioremap(r->start, resource_size(r)); + + r = platform_get_resource(pdev, IORESOURCE_IRQ, 0); + if (!r) { + error = -ENXIO; + goto out_2; + } + nfc_irq = r->start; + + init_waitqueue_head(&irq_waitq); + error = request_irq(nfc_irq, mxc_nfc_irq, 0, "mxc_nd", NULL); + if (error) + goto out_3; + + return 0; +out_3: +out_2: + if (!MXC_NFC_NO_IP_REG) + iounmap(nfc_ip_base); +out_1: + iounmap(nfc_axi_base); +out_0: + return error; +} + +static void mxc_nfc_init(void) +{ + /* Disable interrupt */ + raw_write((raw_read(REG_NFC_INTRRUPT) | NFC_INT_MSK), REG_NFC_INTRRUPT); + + /* disable spare enable */ + raw_write(raw_read(REG_NFC_SP_EN) & ~NFC_SP_EN, REG_NFC_SP_EN); + + /* Unlock the internal RAM Buffer */ + raw_write(NFC_SET_BLS(NFC_BLS_UNLCOKED), REG_NFC_BLS); + + if (!(cpu_is_mx53())) { + /* Blocks to be unlocked */ + UNLOCK_ADDR(0x0, 0xFFFF); + + /* Unlock Block Command for given address range */ + raw_write(NFC_SET_WPC(NFC_WPC_UNLOCK), REG_NFC_WPC); + } + + /* Enable symetric mode by default except mx37TO1.0 */ + if (!(cpu_is_mx37_rev(CHIP_REV_1_0) == 1)) + raw_write(raw_read(REG_NFC_ONE_CYCLE) | + NFC_ONE_CYCLE, REG_NFC_ONE_CYCLE); +} + +static int mxc_alloc_buf(void) +{ + int err = 0; + + data_buf = kzalloc(NAND_MAX_PAGESIZE, GFP_KERNEL); + if (!data_buf) { + printk(KERN_ERR "%s: failed to allocate data_buf\n", __func__); + err = -ENOMEM; + goto out; + } + oob_buf = kzalloc(NAND_MAX_OOBSIZE, GFP_KERNEL); + if (!oob_buf) { + printk(KERN_ERR "%s: failed to allocate oob_buf\n", __func__); + err = -ENOMEM; + goto out; + } + + out: + return err; +} + +static void mxc_free_buf(void) +{ + kfree(data_buf); + kfree(oob_buf); +} + +int nand_scan_mid(struct mtd_info *mtd) +{ + int i; + uint8_t id_bytes[NAND_DEVICE_ID_BYTE_COUNT]; + struct nand_chip *this = mtd->priv; + struct nand_device_info *dev_info; + + if (!IS_LARGE_PAGE_NAND) + return 0; + + /* Read ID bytes from the first NAND Flash chip. */ + this->select_chip(mtd, 0); + + this->cmdfunc(mtd, NAND_CMD_READID, 0x00, -1); + + for (i = 0; i < NAND_DEVICE_ID_BYTE_COUNT; i++) + id_bytes[i] = this->read_byte(mtd); + + /* Get information about this device, based on the ID bytes. */ + dev_info = nand_device_get_info(id_bytes); + + /* Check if we understand this device. */ + if (!dev_info) { + printk(KERN_ERR "Unrecognized NAND Flash device.\n"); + return !0; + } + + /* Correct mtd setting */ + this->chipsize = dev_info->chip_size_in_bytes; + mtd->size = dev_info->chip_size_in_bytes * this->numchips; + mtd->writesize = dev_info->page_total_size_in_bytes & ~0x3ff; + mtd->oobsize = dev_info->page_total_size_in_bytes & 0x3ff; + mtd->erasesize = dev_info->block_size_in_pages * mtd->writesize; + + /* Calculate the address shift from the page size */ + this->page_shift = ffs(mtd->writesize) - 1; + /* Convert chipsize to number of pages per chip -1. */ + this->pagemask = (this->chipsize >> this->page_shift) - 1; + + this->bbt_erase_shift = this->phys_erase_shift = + ffs(mtd->erasesize) - 1; + this->chip_shift = ffs(this->chipsize) - 1; + + return 0; +} + +/*! + * show_device_disable_bi_swap() + * Shows the value of the 'disable_bi_swap' flag. + * + * @dev: The device of interest. + * @attr: The attribute of interest. + * @buf: A buffer that will receive a representation of the attribute. + */ +static ssize_t show_device_disable_bi_swap(struct device *dev, + struct device_attribute *attr, char *buf) +{ + return sprintf(buf, "%d\n", mxc_nand_data->disable_bi_swap); +} + +/*! + * store_device_disable_bi_swap() + * Sets the value of the 'disable_bi_swap' flag. + * + * @dev: The device of interest. + * @attr: The attribute of interest. + * @buf: A buffer containing a new attribute value. + * @size: The size of the buffer. + */ +static ssize_t store_device_disable_bi_swap(struct device *dev, + struct device_attribute *attr, const char *buf, size_t size) +{ + const char *p = buf; + unsigned long v; + + /* Try to make sense of what arrived from user space. */ + + if (strict_strtoul(p, 0, &v) < 0) + return size; + + if (v > 0) + v = 1; + mxc_nand_data->disable_bi_swap = v; + return size; + +} + +static DEVICE_ATTR(disable_bi_swap, 0644, + show_device_disable_bi_swap, store_device_disable_bi_swap); + +/*! + * show_device_ignorebad() + * Shows the value of the 'ignore_bad_block' flag. + * + * @dev: The device of interest. + * @attr: The attribute of interest. + * @buf: A buffer that will receive a representation of the attribute. + */ +static ssize_t show_device_ignorebad(struct device *dev, + struct device_attribute *attr, char *buf) +{ + return sprintf(buf, "%d\n", mxc_nand_data->ignore_bad_block); +} + +/*! + * store_device_ignorebad() + * Sets the value of the 'ignore_bad_block' flag. + * + * @dev: The device of interest. + * @attr: The attribute of interest. + * @buf: A buffer containing a new attribute value. + * @size: The size of the buffer. + */ +static ssize_t store_device_ignorebad(struct device *dev, + struct device_attribute *attr, const char *buf, size_t size) +{ + const char *p = buf; + unsigned long v; + + /* Try to make sense of what arrived from user space. */ + + if (strict_strtoul(p, 0, &v) < 0) + return size; + + if (v > 0) + v = 1; + + /* Only do something if the value is changing. */ + if (v != mxc_nand_data->ignore_bad_block) { + if (v) { + /* + * If control arrives here, we want to begin ignoring + * bad block marks. Reach into the NAND Flash MTD data + * structures and set the in-memory BBT pointer to NULL. + * This will cause the NAND Flash MTD code to believe + * that it never created a BBT and force it to call our + * block_bad function. + */ + mxc_nand_data->saved_bbt = mxc_nand_data->nand.bbt; + mxc_nand_data->nand.bbt = 0; + mxc_nand_data->saved_block_bad = + mxc_nand_data->nand.block_bad; + mxc_nand_data->nand.block_bad = + mxc_nand_block_bad; + } else { + /* + * If control arrives here, we want to stop ignoring + * bad block marks. Restore the NAND Flash MTD's pointer + * to its in-memory BBT. + */ + mxc_nand_data->nand.bbt = mxc_nand_data->saved_bbt; + mxc_nand_data->nand.block_bad = + mxc_nand_data->saved_block_bad; + } + mxc_nand_data->ignore_bad_block = v; + } + + return size; + +} + +static DEVICE_ATTR(ignorebad, 0644, + show_device_ignorebad, store_device_ignorebad); + + +static struct device_attribute *device_attributes[] = { + &dev_attr_disable_bi_swap, + &dev_attr_ignorebad, +}; +/*! + * manage_sysfs_files() - Creates/removes sysfs files for this device. + * + * @create: create/remove the sys entry. + */ +static void manage_sysfs_files(int create) +{ + struct device *dev = mxc_nand_data->dev; + int error; + unsigned int i; + struct device_attribute **attr; + + for (i = 0, attr = device_attributes; + i < ARRAY_SIZE(device_attributes); i++, attr++) { + + if (create) { + error = device_create_file(dev, *attr); + if (error) { + while (--attr >= device_attributes) + device_remove_file(dev, *attr); + return; + } + } else { + device_remove_file(dev, *attr); + } + } + +} + + +/*! + * This function is called during the driver binding process. + * + * @param pdev the device structure used to store device specific + * information that is used by the suspend, resume and + * remove functions + * + * @return The function always returns 0. + */ +static int __devinit mxcnd_probe(struct platform_device *pdev) +{ + struct nand_chip *this; + struct mtd_info *mtd; + struct flash_platform_data *flash = pdev->dev.platform_data; + int nr_parts = 0, err = 0; + + /* get the resource */ + err = mxc_get_resources(pdev); + if (err) + goto out; + + /* init the nfc */ + mxc_nfc_init(); + + /* init data buf */ + if (mxc_alloc_buf()) + goto out; + + /* Allocate memory for MTD device structure and private data */ + mxc_nand_data = kzalloc(sizeof(struct mxc_mtd_s), GFP_KERNEL); + if (!mxc_nand_data) { + printk(KERN_ERR "%s: failed to allocate mtd_info\n", + __FUNCTION__); + err = -ENOMEM; + goto out; + } + + memset((char *)&g_nandfc_info, 0, sizeof(g_nandfc_info)); + + mxc_nand_data->dev = &pdev->dev; + /* structures must be linked */ + this = &mxc_nand_data->nand; + mtd = &mxc_nand_data->mtd; + mtd->priv = this; + mtd->owner = THIS_MODULE; + + this->priv = mxc_nand_data; + this->cmdfunc = mxc_nand_command; + this->select_chip = mxc_nand_select_chip; + this->read_byte = mxc_nand_read_byte; + this->read_word = mxc_nand_read_word; + this->write_buf = mxc_nand_write_buf; + this->read_buf = mxc_nand_read_buf; + this->verify_buf = mxc_nand_verify_buf; + this->scan_bbt = mxc_nand_scan_bbt; + + /* NAND bus width determines access funtions used by upper layer */ + if (flash->width == 2) { + this->read_byte = mxc_nand_read_byte16; + this->options |= NAND_BUSWIDTH_16; + NFC_SET_NFMS(1 << NFMS_NF_DWIDTH); + } else { + NFC_SET_NFMS(0); + } + + nfc_clk = clk_get(&pdev->dev, "nfc_clk"); + clk_enable(nfc_clk); + mxc_nand_data->clk_active = 1; + + if (hardware_ecc) { + this->ecc.read_page = mxc_nand_read_page; + this->ecc.write_page = mxc_nand_write_page; + this->ecc.read_oob = mxc_nand_read_oob; + this->ecc.layout = &nand_hw_eccoob_512; + this->ecc.calculate = mxc_nand_calculate_ecc; + this->ecc.hwctl = mxc_nand_enable_hwecc; + this->ecc.correct = mxc_nand_correct_data; + this->ecc.mode = NAND_ECC_HW; + this->ecc.size = 512; + this->ecc.bytes = 9; + raw_write((raw_read(REG_NFC_ECC_EN) | NFC_ECC_EN), + REG_NFC_ECC_EN); + } else { + this->ecc.mode = NAND_ECC_SOFT; + raw_write((raw_read(REG_NFC_ECC_EN) & ~NFC_ECC_EN), + REG_NFC_ECC_EN); + } + + /* config the gpio */ + if (flash->init) + flash->init(); + + /* Reset NAND */ + this->cmdfunc(mtd, NAND_CMD_RESET, -1, -1); + + /* Scan to find existence of the device */ + if (nand_scan_ident(mtd, NFC_GET_MAXCHIP_SP(), NULL) + || nand_scan_mid(mtd) + || nand_scan_tail(mtd)) { + DEBUG(MTD_DEBUG_LEVEL0, + "MXC_ND2: Unable to find any NAND device.\n"); + err = -ENXIO; + goto out_1; + } + + /* Register the partitions */ +#ifdef CONFIG_MTD_PARTITIONS + nr_parts = + parse_mtd_partitions(mtd, part_probes, &mxc_nand_data->parts, 0); + if (nr_parts > 0) + add_mtd_partitions(mtd, mxc_nand_data->parts, nr_parts); + else if (flash->parts) + add_mtd_partitions(mtd, flash->parts, flash->nr_parts); + else +#endif + { + pr_info("Registering %s as whole device\n", mtd->name); + add_mtd_device(mtd); + } + + /* Create sysfs entries for this device. */ + manage_sysfs_files(true); + + platform_set_drvdata(pdev, mtd); + + return 0; + + out_1: + kfree(mxc_nand_data); + out: + return err; + +} + + /*! + * Dissociates the driver from the device. + * + * @param pdev the device structure used to give information on which + * + * @return The function always returns 0. + */ + +static int __exit mxcnd_remove(struct platform_device *pdev) +{ + struct mtd_info *mtd = platform_get_drvdata(pdev); + struct flash_platform_data *flash = pdev->dev.platform_data; + + if (flash->exit) + flash->exit(); + + manage_sysfs_files(false); + mxc_free_buf(); + + mxc_nand_clk_disable(); + clk_put(nfc_clk); + platform_set_drvdata(pdev, NULL); + + if (mxc_nand_data) { + nand_release(mtd); + free_irq(nfc_irq, NULL); + kfree(mxc_nand_data); + } + + return 0; +} + +#ifdef CONFIG_PM +/*! + * This function is called to put the NAND in a low power state. Refer to the + * document driver-model/driver.txt in the kernel source tree for more + * information. + * + * @param pdev the device information structure + * + * @param state the power state the device is entering + * + * @return The function returns 0 on success and -1 on failure + */ + +static int mxcnd_suspend(struct platform_device *pdev, pm_message_t state) +{ + DEBUG(MTD_DEBUG_LEVEL0, "MXC_ND2 : NAND suspend\n"); + + /* Disable the NFC clock */ + mxc_nand_clk_disable(); + + return 0; +} + +/*! + * This function is called to bring the NAND back from a low power state. Refer + * to the document driver-model/driver.txt in the kernel source tree for more + * information. + * + * @param pdev the device information structure + * + * @return The function returns 0 on success and -1 on failure + */ +static int mxcnd_resume(struct platform_device *pdev) +{ + DEBUG(MTD_DEBUG_LEVEL0, "MXC_ND2 : NAND resume\n"); + + /* Enable the NFC clock */ + mxc_nand_clk_enable(); + + return 0; +} + +#else +#define mxcnd_suspend NULL +#define mxcnd_resume NULL +#endif /* CONFIG_PM */ + +/*! + * This structure contains pointers to the power management callback functions. + */ +static struct platform_driver mxcnd_driver = { + .driver = { + .name = "mxc_nandv2_flash", + }, + .probe = mxcnd_probe, + .remove = __exit_p(mxcnd_remove), + .suspend = mxcnd_suspend, + .resume = mxcnd_resume, +}; + +/*! + * Main initialization routine + * @return 0 if successful; non-zero otherwise + */ +static int __init mxc_nd_init(void) +{ + /* Register the device driver structure. */ + pr_info("MXC MTD nand Driver %s\n", DVR_VER); + if (platform_driver_register(&mxcnd_driver) != 0) { + printk(KERN_ERR "Driver register failed for mxcnd_driver\n"); + return -ENODEV; + } + return 0; +} + +/*! + * Clean up routine + */ +static void __exit mxc_nd_cleanup(void) +{ + /* Unregister the device structure */ + platform_driver_unregister(&mxcnd_driver); +} + +module_init(mxc_nd_init); +module_exit(mxc_nd_cleanup); + +MODULE_AUTHOR("Freescale Semiconductor, Inc."); +MODULE_DESCRIPTION("MXC NAND MTD driver Version 2-5"); +MODULE_LICENSE("GPL"); |