summaryrefslogtreecommitdiff
AgeCommit message (Expand)Author
2013-11-07Code optimization for calculation of correct binning/skipping values for mt9p...Andrei Andreyanau
2013-11-07fec: tune RSEM and RSFL values for tapeout 1.0Eric Nelson
2013-11-07fec: enable tx/rx of pause frames for mx6qTroy Kisky
2013-11-07fec: fix rx error countsTroy Kisky
2013-11-07fec: stop the "rcv is not +last, " error messagesTroy Kisky
2013-11-07phyFLEX-i.MX6: Set pice reset gpioChristian Hemp
2013-11-07phyFLEX-imx6: Set SD3 WP to correct gpioChristian Hemp
2013-11-07phyflex-i.MX6: Mux GPIO 0 for usb1 enableChristian Hemp
2013-11-07phyFLEX-i.MX6: Set pice reset gpioChristian Hemp
2013-11-07phyFLEX-i.MX6: Added new GPIOsChristian Hemp
2013-11-07phyFLEX-i.MX6: Remove PEB codeChristian Hemp
2013-11-07phyFLEX-i.MX6: remove spi nor partionsChristian Hemp
2013-11-07phyflex-iMX6: Remove phyflex fixupChristian Hemp
2013-11-07phyflex-imx6: Remove NAND partition defenition from codeChristian Hemp
2013-11-07mt9m001: Fix the testpattern bit overwritten.Christian Hemp
2013-11-07phyflex: only use second ldb fb if hdmi is not usedDaniel Mierswa
2013-11-07phyflex: introduce pin define for hw introspectionDaniel Mierswa
2013-11-07imx6 power offChristian Hemp
2013-11-07phyflex-imx6: add selection for phyCAM-P and S+Christian Hemp
2013-11-07Add Display ETM0700G0DH6Christian Hemp
2013-11-07phyflex-imx6: Added etd touch driver to platfomChristian Hemp
2013-11-07EDT-FT5x06: named the requested gpiosEnrico Scholz
2013-11-07EDT-FT5x06: allow unconfigured reset gpioEnrico Scholz
2013-11-07EDT-FT5x06: kernel 3.0 adaptationsEnrico Scholz
2013-11-07EDT-FT5x06: initial checkin of upstream FT5x06 patchEnrico Scholz
2013-11-07phyFLEX-i.MX6: remove CONFIG_PHYFLEX_SOC_1362_0Christian Hemp
2013-11-07Fixed mt9p031 camera driver. Recalculated values for correct vblank/hblank. m...Andrei Andreyanau
2013-11-07Fixed clock rate for cameras to be close to 26MHzAndrei Andreyanau
2013-11-07Fixed parent clock source for cameras.Andrei Andreyanau
2013-11-07Remove rests of debug output in pmic initialization codeDmitry Lavnikevich
2013-11-07Fixed support for Micrel's ksz9031 Gigabit phy modified: drivers/net/phy/micr...Andrei Andreyanau
2013-11-07Added mt9p031 camera sensor supportRaman Tunik
2013-11-07Added support for powe-down the ksz9021 ethernet adapter modified: arch/arm/m...Andrei Andreyanau
2013-11-07Added default mx6 configAnatoly Palto
2013-11-07Fix for latest freescale patchesUladzimir Bely
2013-11-07Added support working two touch screens simultaneouslyAnatoly Palto
2013-11-07Old board ethernet fixesGrigory Milev
2013-11-07Fix ethernet for old 1362_0 modulesGrigory Milev
2013-11-07For phyFlex Fix conflict init interrupt tochscreen 1 and camera clk0 fo soc 1...Anatoly Palto
2013-11-07Added support for LVDS camera on 1st lvds portDmitry Lavnikevich
2013-11-07Minor cleanup: remove constRaman Tunik
2013-11-07Added default LVDS out enable in the mt9v022 camera driver.Dmitry Lavnikevich
2013-11-07Fixed chip id register read for ethernet device in board specific codeAndrei Andreyanau
2013-11-07Fixed support for mt9v024 colour/monochrome camera sensor (uses mt9v022 kerne...Andrei Andreyanau
2013-11-07Added header file for mt9v024 camera that defines camera's features new file:...Andrei Andreyanau
2013-11-07Barebox environment size now 4MbGrigory Milev
2013-11-07Added identities for mt9v024 colour/monochrome camera sensorsAndrei Andreyanau
2013-11-07Added support MAX7301 (SPI to GPIO)Anatoly Palto
2013-11-07Fixed commentary for VM-009/VM-006 camerasAndrei Andreyanau
2013-11-07phyFLEX: Remove unused cameras linksYauhen Kharuzhy
generated by cgit v1.2.3 (git 2.0.4) at 2024-04-26 23:19:01 +0000