| Age | Commit message (Collapse) | Author |
|---|
|
Fix wrong memory size calculation in clamshell mode
Signed-off-by: Tingting Meng <tingting.meng@altera.com>
Signed-off-by: Alif Zakuan Yuslaimi <alif.zakuan.yuslaimi@altera.com>
Reviewed-by: Tien Fong Chee <tien.fong.chee@altera.com>
|
|
Clean up bit-shift by zero bit
Signed-off-by: Tingting Meng <tingting.meng@altera.com>
Signed-off-by: Alif Zakuan Yuslaimi <alif.zakuan.yuslaimi@altera.com>
Reviewed-by: Tien Fong Chee <tien.fong.chee@altera.com>
|
|
This is for new platform enablement for Agilex7 M-series.
Add DDR driver for Agilex7 M-series. This driver is designed to support
DDR and HBM memory. The official HBM handoff is not ready yet, therefore
hardcoded handoff is used for HBM driver validation on mUDV board.
Signed-off-by: Tingting Meng <tingting.meng@altera.com>
Signed-off-by: Alif Zakuan Yuslaimi <alif.zakuan.yuslaimi@altera.com>
Reviewed-by: Tien Fong Chee <tien.fong.chee@altera.com>
|
|
Add uibssm mailbox driver for Agilex7 M-series. HPS will interact with UIB
and HBM subsystem through software defined mailbox interface.
HPS can retrieve HBM memory interface calibration status, UIB
configuration, memory interfae configuration, trigger calibration and etc
with the list of supported mailbox command type and opcode.
Signed-off-by: Tingting Meng <tingting.meng@altera.com>
Signed-off-by: Alif Zakuan Yuslaimi <alif.zakuan.yuslaimi@altera.com>
Reviewed-by: Tien Fong Chee <tien.fong.chee@altera.com>
|
|
The DDR data rate must be set correctly in the DDRIOCTRL
register according to the Actual Clock Frequency (ACF) value.
By enabling the reading of ACF value from bit 18 of the boot
scratch register during initialization, the DDR data rate is
able to be configured accurately.
Signed-off-by: Alif Zakuan Yuslaimi <alif.zakuan.yuslaimi@altera.com>
Reviewed-by: Tien Fong Chee <tien.fong.chee@altera.com>
|
|
Remove redundant code for MPFE CSR firewall disabled as this was
already set in DTreg dts.
Signed-off-by: Tien Fong Chee <tien.fong.chee@altera.com>
Signed-off-by: Alif Zakuan Yuslaimi <alif.zakuan.yuslaimi@altera.com>
Reviewed-by: Tien Fong Chee <tien.fong.chee@altera.com>
|
|
Setting up firewall regions based on SDRAM memory banks configuration
(up to CONFIG_NR_DRAM_BANKS banks) instead of using whole address space.
First 1 MiB (0 to 0xfffff) of SDRAM is configured as secure region,
other address spaces are non-secure regions. The ARM Trusted Firmware (ATF)
image is located in this first 1 MiB memory region. So, this can prevent
software executing at non-secure state EL0-EL2 and non-secure masters
access to secure region.
Add common function for firewall setup and reuse for all SoC64 devices.
Signed-off-by: Alif Zakuan Yuslaimi <alif.zakuan.yuslaimi@altera.com>
Reviewed-by: Tien Fong Chee <tien.fong.chee@altera.com>
|
|
The function socfpga_get_handoff_size returns an int so make the struct
fields used to accept the return value also an int so that testing for
less than 0 is then valid.
This issue was found by Smatch.
Signed-off-by: Andrew Goodbody <andrew.goodbody@linaro.org>
|
|
Use consistent lowercase hex prefix style in drivers/*
Does not change hex prefix case in allcaps uppercase style error messages
Signed-off-by: E Shattow <e@freeshell.de>
|
|
ECC debug information was enhanced to improve the readability of error
messages.
Signed-off-by: Tingting Meng <tingting.meng@altera.com>
|
|
In-line ECC support was added for LPDDR by reserving the last one-eighth
of the memory space for ECC data. Full memory initialization using the
BIST MEM INIT mailbox command, based on address and size, is required to
correctly generate ECC data and enable proper ECC logic verification.
Signed-off-by: Tingting Meng <tingting.meng@altera.com>
|
|
Data structure, dramaddrw, is defined as u32. Compiler performs
32-bit arithmetic and logic operations on this data structure. Fix
is provided to avoid integer overflow while performing shifting
operations greater than 32-bit.
Signed-off-by: Naresh Kumar Ravulapalli <nareshkumar.ravulapalli@altera.com>
Reviewed-by: Tien Fong Chee <tien.fong.chee@altera.com>
|
|
It is confusing to have both "$(PHASE_)" and "$(XPL_)" be used in our
Makefiles as part of the macros to determine when to do something in our
Makefiles based on what phase of the build we are in. For consistency,
bring this down to a single macro and use "$(PHASE_)" only.
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Adding DDR driver support for Agilex5 series.
Signed-off-by: Tingting Meng <tingting.meng@altera.com>
|
|
These TUs currently rely on getting a declaration of schedule()
through some nested include. Include the proper header directly.
Signed-off-by: Rasmus Villemoes <ravi@prevas.dk>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
|
|
Use XPL_ as the symbol to indicate an SPL build. This means that SPL_ is
no-longer set.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Use the new symbol to refer to any 'SPL' build, including TPL and VPL
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Drop all duplicate newlines. No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
|
|
As part of bringing the master branch back in to next, we need to allow
for all of these changes to exist here.
Reported-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
When bringing in the series 'arm: dts: am62-beagleplay: Fix Beagleplay
Ethernet"' I failed to notice that b4 noticed it was based on next and
so took that as the base commit and merged that part of next to master.
This reverts commit c8ffd1356d42223cbb8c86280a083cc3c93e6426, reversing
changes made to 2ee6f3a5f7550de3599faef9704e166e5dcace35.
Reported-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Remove <common.h> from this driver directory and when needed
add missing include files directly.
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
In order to make it easier to move on to dropping common.h from code
directly, remove common.h inclusion from the rest of the header file
which had been including it.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
The fdt_addr_t and phys_addr_t size have been decoupled. A 32bit CPU
can expect 64-bit data from the device tree parser, so use
devfdt_get_addr_index_ptr instead of the devfdt_get_addr_index function
in the various files in the drivers directory that cast to a pointer.
As we are there also streamline the error response to -EINVAL on return.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Globally replace all occurances of WATCHDOG_RESET() with schedule(),
which handles the HW_WATCHDOG functionality and the cyclic
infrastructure.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Tom Rini <trini@konsulko.com> [am335x_evm, mx6cuboxi, rpi_3,dra7xx_evm, pine64_plus, am65x_evm, j721e_evm]
|
|
Convert the constant integer to 'phys_size_t' to avoid overflow
when calculating the SDRAM size.
Signed-off-by: Dinesh Maniyam <dinesh.maniyam@intel.com>
Reviewed-by: Tien Fong Chee <tien.fong.chee@intel.com>
|
|
Replace with phys_size_t for all memory size variables declaration
for the sake of scalability. phys_size_t is defined in
/arch/arm/include/asm/types.h.
Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
|
|
Bit[7-4] for both register seq2core and core2seq handshake in HPS are not
required for triggering DDR re-calibration or resetting EMIF. So, ignoring
these bits just for playing it safe.
Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
|
|
All the source code of sdram_n5x.c are from Intel, update the license to
use both GPL2.0 and BSD-3 Clause because this copy of code may used for
open source and internal project.
Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
|
|
|
|
Signed-off-by: Wolfgang Denk <wd@denx.de>
|
|
The KBUILD_BASENAME contains just the name of the compiled module,
in this case 'sequencer', rather than a full path to the compiled
file. Use it to prevent pulling the full path into the U-Boot binary,
which is useless and annoying.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Siew Chin Lim <elly.siew.chin.lim@intel.com>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Cc: Tien Fong Chee <tien.fong.chee@intel.com>
|
|
The DDR subsystem in Diamond Mesa is consisted of controller, PHY,
memory reset manager and memory clock manager.
Configuration settings of controller, PHY and memory reset manager
is come from DDR handoff data in bitstream, which contain the register
base addresses and user settings from tool.
Configuration settings of memory clock manager is come from the HPS
handoff data in bitstream, however the register base address is defined
in device tree.
The calibration is fully done in HPS, which requires IMEM and DMEM
binaries loading to PHY SRAM for running this calibration, both
IMEM and DMEM binaries are also part of bitstream, this bitstream
would be loaded to OCRAM by SDM, and configured by DDR driver.
Signed-off-by: Siew Chin Lim <elly.siew.chin.lim@intel.com>
Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
|
|
Minimum 1GB memory size is required in current memory test, so this patch
improves the memory test for processing memory size less than 1GB, and
the size in power of two.
Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
|
|
Create common macro TARGET_SOCFPGA_SOC64 for Stratix10 and Agilex.
Signed-off-by: Siew Chin Lim <elly.siew.chin.lim@intel.com>
|
|
The values of left_edge[0] and right_edge[0] are overwritten before they
are used. Remove the superfluous assignments.
Fixes: 285b3cb939a8 ("dm: ddr: socfpga: fix gen5 ddr driver to not use bss")
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Move this out of the common header and include it only where needed. In
a number of cases this requires adding "struct udevice;" to avoid adding
another large header or in other cases replacing / adding missing header
files that had been pulled in, very indirectly. Finally, we have a few
cases where we did not need to include <asm/global_data.h> at all, so
remove that include.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Most drivers use these access methods but a few do not. Update them.
In some cases the access is not permitted, so mark those with a FIXME tag
for the maintainer to check.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Pratyush Yadav <p.yadav@ti.com>
|
|
Try to maintain some consistency between these variables by using _plat as
a suffix for them.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
This name is far too long. Rename it to remove the 'data' bits. This makes
it consistent with the platdata->plat rename.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
We use 'priv' for private data but often use 'platdata' for platform data.
We can't really use 'pdata' since that is ambiguous (it could mean private
or platform data).
Rename some of the latter variables to end with 'plat' for consistency.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
This construct is quite long-winded. In earlier days it made some sense
since auto-allocation was a strange concept. But with driver model now
used pretty universally, we can shorten this to 'auto'. This reduces
verbosity and makes it easier to read.
Coincidentally it also ensures that every declaration is on one line,
thus making dtoc's job easier.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
The Linux coding style guide (Documentation/process/coding-style.rst)
clearly says:
It's a **mistake** to use typedef for structures and pointers.
Besides, using typedef for structures is annoying when you try to make
headers self-contained.
Let's say you have the following function declaration in a header:
void foo(bd_t *bd);
This is not self-contained since bd_t is not defined.
To tell the compiler what 'bd_t' is, you need to include <asm/u-boot.h>
#include <asm/u-boot.h>
void foo(bd_t *bd);
Then, the include direcective pulls in more bloat needlessly.
If you use 'struct bd_info' instead, it is enough to put a forward
declaration as follows:
struct bd_info;
void foo(struct bd_info *bd);
Right, typedef'ing bd_t is a mistake.
I used coccinelle to generate this commit.
The semantic patch that makes this change is as follows:
<smpl>
@@
typedef bd_t;
@@
-bd_t
+struct bd_info
</smpl>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
|
|
Move this uncommon header out of the common header.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Move this uncommon header out of the common header.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Move this header out of the common header.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Move this uncommon header out of the common header.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Move this header out of the common header. Network support is used in
quite a few places but it still does not warrant blanket inclusion.
Note that this net.h header itself has quite a lot in it. It could be
split into the driver-mode support, functions, structures, checksumming,
etc.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
sandbox conversion to SDL2
TPM TEE driver
Various minor sandbox video enhancements
New driver model core utility functions
|
|
At present dm/device.h includes the linux-compatible features. This
requires including linux/compat.h which in turn includes a lot of headers.
One of these is malloc.h which we thus end up including in every file in
U-Boot. Apart from the inefficiency of this, it is problematic for sandbox
which needs to use the system malloc() in some files.
Move the compatibility features into a separate header file.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Add DDR2 support to Gen5 DRAM driver. As the DDR2 macro names generated
by Quartus are named differently than the DDR3 ones, use anon unions to
store them in the same structures, without growing their size.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
|
